I had my 3.5L oil change and they stripped the motor oil screw. Car leaked oil and I thought my engine was done. Car started to have really loud knocking sound. I did an oil change myself and then the Boise was 95% gone. But my 3.5 started to misfire really bad with vibrations. I replaced spark plugs, coils packs, egr valve, cam sensor, crank sensor, Map sensor, air temperature sensor, throttle body, injectors, coil packs signal cables and the car still having a very rough idle and at some point will stall. I also clean the upper intake manifold. No check engine light no code. I now believe that my rocket arms or lifters are gone. Thank you for the video.

Where did you get your information. The plastic (orange) ring simply holds the pivot in place for assembly/disassembly. Once installed the foot/pivot which sits on the valve is held against the lifter by pressure so the missing plastic doesnt do anything at that point and WILL NOT effect performance. If the plastic falls off and eventually ends up in the oil pan it highly unlikely that it will get into the engine as the oil pump pickup has a screen. I have 2- 3.5 cars and a 4 cyl that uses essentially the same style lifter. Also the lifters are available for a pretty inexpensive price. You can knock the old ones out with a small punch, just be aware there is a small plate shaped disk above the lifter that has to be oriented properly when installing new lifter.

My o4 Pacifica will rattle before it start it will turn over for a long time it seem it has to build pressure for valve to open but oil pressure is high and good is the tappit suppose to hold their position or will they contract when motor turns off

Chrysler hasnt made a decent valvetrain since the begining of time ....

Yo tengo el problema con un 300chraisler 2006 el problema son los bozos no puedo cambiarlos

I have my 3.5 lower intake off and noticed that I have blown gaskets . I don't have any compression in passager side cylinders 0 compression in a cylinder 50psi in another 70 in another all on passager side of the motor the drivers side is 170 150 125

can the intake also have a blocked egr port on these? I have the broken lash adjuster noise and rough idle, but also a p0401. egr and tube are new and clean. I seen that other vehicles can be clogged in intake ports.

Is this a difficult repair? I'm a preacher and I don't have a ton of money. Any instructional stuff out there? I have a tick from the rocker arms.

Let me ask a question. Heads were worked on due to timing belt bearing tensioner broke. Now when putting heads back. Passenger side is already set and torqued. Driver side head when placing rockers for some reason cam shaft locks while trying to adjust them. Any help I would appreciate it. Thanks

Have a friend with this issue. How long is the job from start to finish doing both sides. 2001 Chrysler LHS? Thank you

hey good day I watched your video on 2006 Chrysler 300 3.5 it was so useful to me I have the same Chrysler in my house but I need your help my question is I took the valve rocker arms shifter lifter out so when I got the new one i try to put it back in I think the camshaft shifted because I pushed the car back in my compound to have a space before the new parts came through yesterday to fit in what I need to do if you don't mind thank you

What causes the oil to burn on them ??? Also why so much play on some rockers is it wearing the shaft down making rocker or shaft go bad??

Hi do you know where the vvt solenoid (oil control valve) is on the 3.5 engine chrysler or charger

I was just wondering what is the torque spec

this due to bad oil recirculation?

Will bad rocker arms cause a P300 random cylinder misfire code and P0016 on the 3.5? My timing belt jumped the gear when the tensioner pulley came apart. I set the timing belt correctly but I have this issue now.

hey there, isn't it much cheaper to replace just the Hydraulic Lifters rather than buying new rocker arms..I recently had the same issue with my 07 chrysler 300c 3.5L it had ticking/tapping noise and I'm still yet to decide whether to replace the arms or just the lifters which appears to be way cheaper ..

Awesome video!. Does this engine have 2 rocker arms??

Hey i have a 2010 charger with the 3.5 i keep getting a 306 code misfire on cylinder 6 ive tryed everything to fix i read some were this could be the rocker arm ive done change plugs ,coils, injectors,cam sensor ,crankshaft sensor, please help if you can a.s.a.p thanks

I have a 2006 dodge charger and its knocking pretty loud! I don't beat my cars normally but I raced a kid one day and now its knocking. Any chance that this (rocker arm) is my problem? Or do you think its a rod? Also if I drive it then shut the car off and try to restart it, its really hard to start or the battery is dead but its starts up great the first time. maybe a timing issue due to the bad rocker???

when installing the rocker arms do I need to find top dead center

Is this a common problem with the 3.7 jeeps as well?

Good morning,need some help please

Thank you my friend for the advice, so here is my question, i took over payments on a 2010 Chrysler 300 for a female friend of mine and that being said when I got the car I checked the fluids and the oil and the oil was BONE dry, I added oil rite away and I asked her how long she had ran the car with no oil, well still after a month of having the car she has not gave me a straight answer, So after about 2 days of having the car and noise appears and it really isnt a knock par say as much as it is a loud tick, I know that the fuel injections have a small tick but this is loud but it is not " Knocking" that being said after watching this video I am thinking that it is the rocker valve at the upper part of the motor, it is coming from rite under the fuel injection and from the top of the motor, I did try some lucas cause my friend recommended it but it is not help the noise, what would you think it is?? I could post a video if you need me to

Would this make my 3.5 have no compression in 1 cyc

Question can the same thing happened on the exhaust side or could it also affect the compression in the cylinders I have the passenger side has excellent compression on each cylinder then I go to the driver side and the compression is terrible on each cylinder I was just wondering before I pull the head

I have a 2009 Dodge Charger I was moving it (street sweepers) and right when I started loud knock noises appears than go away I let it warmed up and slowly knock noises coming back I put it in drive I heard no knocking noise I’m too scared to drive it just to see if it’s knocking louder smh is this the issues I have ? Please help

Would this show low compression with this issues ?

So can the plastic beadlock and swivel be replaced? Do I have to buy all new rockers to replace the orange plastic retainers?

do I have to pull the head just cause I hear a a tapping noise

Hi quick question I bought some rocker arm assembly when I received it the yellow thing like the orange thing on your video on the lifter is broken but I glued it would it still work ?

What's the. The tourque soec. For the rocker arm bolts

So these engines have no lifters ?

Are those little silver tips within the orange ring supposed to swivel?? Please let me know asap

do you know if the 1996 3.5 in the Intrepid uses the same type cam and rocker assembly?

Hey guys I have a Chrysler town and country 2015 and I have the same problem and I bring the car to the dealership to get it fixed and after a month I go back to the dealership to see if they fix it yet and they give me the surprise they have to keep my car for 3 more months because the roller rocker and the lifters they are out of stock I called already at Chrysler customer service and they don’t give me a answer. Can you please guys let me know what can I do please

On the tapit lash how much play is there supposed to be

Are u here?

😢

1999/2010

Good video, thanks. Here's an '04 Pacifica 3.5 that I have. forgive the camera work but I'm trying to identify this - kzfaq.info/get/bejne/gtR4odCQy6nNh6s.html Thanks.