I also enjoy an occasional game of "Find where the hell they hid the oil filter.".
@mainengines4 жыл бұрын
Great Speed Handle work John! Used one myself, for 38 years!
@leeregan80174 жыл бұрын
A change to see a speed brace being used these days!! Good video again as usual John 👍👍👍👍👍
@garyoneill30522 жыл бұрын
Great advice and video mate thanks for taking the time to make and post it👍👍
@tigercat1966 Жыл бұрын
Thanks Just bought one today ..looking forward to changing oil on it glad you mention spanner size Marra
@fergiesunited4 жыл бұрын
Great video just done my van recently by following your steps Thanks
@toyotoe37325 ай бұрын
Before watching this video I used to press oil filter into cap first, and then nervous if spigot was seated in recess or crushed or snapped off. Thanks for sharing how to do it correctly.
@demondunk4 жыл бұрын
The joys of paper filters. Had a Skoda fabia in the workshop this week. Hadn't had an oil chance in a few years. The O ring had gone flat so the oil was leaking everywhere.
@wetnwild806 ай бұрын
Thanks, Good video. Was going to go to the garage and get interim service costing £145. See this and thought I'll have a go myself. Done it no problem with ramps. Thanks for saving me money👍
@stephenwagar26634 жыл бұрын
Nice To Get A Little Glance Of What You Do 40 Hours A Week ! Of Course I'm A Hard Core Subscriber And Will Watch Any Video You Make With Great Interest ! 47 Thumbs Up
@themustard2 жыл бұрын
Very clear video and commentary. Thank you so much for the info and explanations.
@Mypitbull822 жыл бұрын
Nice and straight to the point video cheers mate.
@kingofthecelts22473 жыл бұрын
John great video best by far . A great help . Thanks . Dublin Ireland ☘👍
@mgtfbluestreak39562 жыл бұрын
Fantastic..great information about snapping that lug off the filter...cheers
@bostedtap83994 жыл бұрын
Nice job well done. I did a double oil and filter change on my 1993 Diesel Mondeo, this was my first of many Diesel's, I could not believe that the oil still looked black as coal. I then changed to a semi-synthetic oil, and noticed better mpg, only 2 to 3 miles per gallon, but my annual mileage was circa 45k at that time. Mineral oils do not retain contaminants in suspension for prolonged periods, I found this out when I used to rent a council lock up car garage, and after an oil change, left the used oil in a newish tin, forgot about it, then many months later, was puzzled as to why it appeared new/clear?. Compare to fully synthetic, where as an experiment, I retained a small amount in a sealed jar, this was in 2004, and it's still as black as coal.🤔
@pauljackson65932 жыл бұрын
Just got my car back from service and had a leak on driveway.. think from oil filter stopped now so must have been residue . But as you say annoying. I like how you used a solvent to clean it . Great idea . Good video
@MrGammyballz2 жыл бұрын
Thank you for sharing sir, good tip with the filter too 👍🏻
@simoncrouch15413 жыл бұрын
good vid. sound and straight to the point. no phaffing about. I got the same motor in mine. tho went to check the oil and the whole dipstick tube came out.. anyone else had this happen.
@royevans45812 жыл бұрын
Thanks very much mate, will get that done today.
@noahmaher77063 жыл бұрын
Top job ! Very professionel thanks 👌💪
@markyoung134 жыл бұрын
I call these Pringle engines, once they've eaten one turbo they just can't stop...
@glenndevlin16353 жыл бұрын
Fantastic job there mate 👍 It's good to see you fit the filter to the housing first then you know the spigot is firmly in place. A lot of videos show them fitting the filter into the cover first which surely won't let the spiggot locate correctly. Glen.
@fernandostanic20353 жыл бұрын
I was thinking the same but after watichg this video i understand now how it works if you put filter first to the cap and them screw the carp with filter to the housing. Mahle panented this design for 1.6 hdi. m.kzfaq.info/get/bejne/j7l4nMlmq8rJZ3k.html
@ShowMoneyz3 жыл бұрын
Yeah, no mistake in both ways. Official service first put filter in cap and then screw. That pattern makes alone to put filter in right position and fit in little hole
@zephyrold24784 жыл бұрын
If you notize, the oil dripping of the dipstick is already black, that is because this engine´s drain plug is sitting about an inch higher than the bottom of the oil pan so you never get the last 1/2 liter of oil out of it, this and the banjo bolt with a mesh screen have costed so many turbo´s that aftermarked you can get a oil pan with the drain plug further down, as far as I know neither Citroen/Peugeot or Ford would recognise the problem so owners had to pay them self for turbo´s
@tonyoconnor67843 жыл бұрын
Lovely video a great help thank you 🍀👍
@richardfife8192 Жыл бұрын
Just think in a 100 years looking back at these videos.... Be like us looking back at steam powered cars.
@derekmorse81712 жыл бұрын
excellent video, thank you.
@konbloc2 жыл бұрын
thank you for the vid..helped a lot👍👍👍👍👍
@danc82784 жыл бұрын
The early 1.6HDi engines had faulty injector seals, it's one way that carbon ends up in the oil and knackers the turbos. There's a banjo bolt in the turbo oil supply with a mesh screen that gets clogged and starves the turbo of oil.
@zephyrold24784 жыл бұрын
I second that.
@simoncrouch15413 жыл бұрын
@@zephyrold2478 so clean mesh or remove it. have heard of this with other motors.
@TheDajoca3 жыл бұрын
Also, IIRC, the oil pickup pipe and filter were smaller on the earlier versions, so took less to block and shred the turbo.
@rmc52782 жыл бұрын
hi how early ?
@ElninhoKoji3 ай бұрын
Thanks, I've changed the oil on my car 😊
@jusb10664 жыл бұрын
Video of John at his day job 👍
@emporerzurg21254 жыл бұрын
would like to see more the car maintenance and repair how to's on your channel
@ericmcrae77584 жыл бұрын
Hi John The battery terminals looked like a clean would help.
@MartsGarage Жыл бұрын
Hello John! Very good guidance video. I'm looking to do exactly this job on my C3 Picasso. Tell me, have you ever heard of a speedbrace referred to as a "tear-arse"? I don't know if the term is universal or just a Longbridge thing. Anyway, good to see the mechanic mechanicing and not just pissing about. All the best, Mart in Solihull.
@tomcardale55964 жыл бұрын
I always used to try and keep my Defender up to the fuller end of the dipstick, but it uses large quantities of oil if I do. It uses oil until it gets to bang in the middle of the dipstick then the level doesn't move until the next service. So I now fill it up to half way and leave it.
@Uktaxation Жыл бұрын
Made it easy, thanks
@brightspark4817 Жыл бұрын
good video well explained i have a 0.19 pug but it takes 0 .30 oil not 5 .30
@britishreaction544 жыл бұрын
Nice video.
@jix1774 жыл бұрын
Good video.
@randomdude17864 жыл бұрын
Most people probly would say "yaaaa" some line tech work. I did that for a while load test the battery, check coolent ph/ freeze point, Inspect for brake pad wear, visual for leak's, smoked rotors(sticking pistons/ floating hardware) fill out the check list so it could be put in the data base for the repeat customers you could tell pretty much what you would see befor opening the hood coolent ph and battery state of health deterioration generaly fallows a predictable curve of decline sure wish it paid more thogh
@SeanBZA4 жыл бұрын
Reminds me, I should change my oil, it has done nearly 1 year, almost 10000km. Due before the end of the month, the little display has been telling me that for the last week.
@HeavensEye666 Жыл бұрын
Thank you 👍
@aubreybest33372 жыл бұрын
Very helpful
@kalwinqhack57962 жыл бұрын
Thx mate
@MaturePatriot4 жыл бұрын
That filter placement was definitely designed by an engineer, not a mechanic! A quart of oil is now over $6 US, here in the States. I loved how you cleaned off the excess oil with solvent, a touch of professionalism. You are a man of many talents.
@flybobbie14493 жыл бұрын
Good quality Mobil 1 5litre (4.5 quart) oil here UK £40 ($45).
@arshadmahmood1845 Жыл бұрын
Nice video
@stevecox25304 жыл бұрын
Thanks John, will that service reset work the same on my 54 reg 307? The dash display looks very similar, so I assume this was the same era.
@tomroskell4034 жыл бұрын
What was wrong with spin on filters eh ? When I serviced my last transit I was shocked with the plastic filter housing
@damianbanaszak5467 Жыл бұрын
Hi John. Great video. I have done the same at my Peugeot partner van but after job a have done the low pressure oil light turned on, when I rev a bit up is going off but then come back again. Don’t know what’s wrong with it?
@joecolanjr.81494 жыл бұрын
👍👍
@schwellenzaehler45874 жыл бұрын
Hello John, that was my day job more than 30 years ago, ....but i worked on Trucks and Transporters. When i see your vid, it came all back like it was yesterday. Have you not a rollable wasteoil pott? Its your back, that kills everybodys health, when you must work nearly 50 years in this job. Hope you can retire soon, how many years you have left? Best Johann/ in english ...John😉
@g.s.yeppoon7237 Жыл бұрын
Thanks. Why does the air intake hose go to a dead end at the oil filter? Doesn't make sense to me
@michaellinahan77404 жыл бұрын
as an expat now in Aus the sparsity of diesel cars over here always amazed but with no MOT (outside NSW) there are not the tight controls over emissions and hence servicing so those diesels that are around tend to be dirty, mobile smoke machines but I understand that they are soon to be banned up there is that correct?
@waynesanderson34457 ай бұрын
Wonder if you could get something to suck the rest of the oil out from the sump plug
@oooyugi Жыл бұрын
Cheers
@t0adgr0w3 жыл бұрын
I Just changed my oil filter and I swear there was no old o ring! I just put my new one on but not sure if I put the o ring in the right place as it was fairly tight to do up. How wrong can I have gotten it? Lol
@sweenep864 жыл бұрын
Look very similar to the MK4 mondeo filter, but that needs a cranked filter tool to remove.
@terranceprice70062 жыл бұрын
I dont need one on my Mk4 2.0L diesel, long extension and ratchet used them for years.
@andywilliams11604 жыл бұрын
Good video John, I do hate to see all the plastic on modern engines but it's standard now.
@mickyharkin65572 жыл бұрын
thanks
@leedale40084 жыл бұрын
Clean tidy job John,crap French car though but I suppose they do keep my business going.
@TheDajoca3 жыл бұрын
Berlingo / Partners are brilliant cars and appear to be more reliable than many other "premium" brands.
@priteshchampaneri51013 жыл бұрын
You can't get all the oil out of that sump. There's 500ml left inside because of the design. Therfore using a extraction machine is better on this engine
@JorgenRomeMojo2 жыл бұрын
I took mine off and cleaned it, the oil left in the pan was like sand paper because of all the metal particles that normaly drains with the oil over time...
@Mr11ESSE111 Жыл бұрын
Is oil filter without that notch on the filter good too for replace!?
@blakkelure2 жыл бұрын
Its a shame I dont understand a word he is saying but nice video!
@tomlee79664 жыл бұрын
is this your shop John?
@MyTubeSVp4 жыл бұрын
Renault too !
@FrontSideBus4 жыл бұрын
Twastard automotive lol.. Love it. I wouldn't mind seeing more car vids tbh.
@shoots20014 жыл бұрын
If you scroll back to his really early vids there are some more car ones.
@FrontSideBus4 жыл бұрын
@@shoots2001 Cheers bet yeah I know ;)
@barrypage72204 жыл бұрын
Always Always replace the sump plug washer, its just not worth skimping pennies when servicing your own car
@unforseenlaboratories80172 жыл бұрын
Why?
@Emilio574 жыл бұрын
Nice instructional video, I've just bought a 2009 1.6 75ps and am giving it a once over in the engine bay and I have found the engine top cover is covered with a black residue around the base of the injectors and the cover, that seems to be baked hard and is like a bit of coal. I am chipping it out carefully with a screw driver and blowing it out with an air blow gun, any tips on what has caused this, I'm guessing an oil leak that's pooling on top of the cover then getting baked hard, or leaking injector seals. any advice greatly appreciated
@beany19874 жыл бұрын
You have a injector leaking by the sounds of it also very common on these dv6 engines if you don't look after them.
@markowen71644 жыл бұрын
Do you check the oil when the engine is cold? Or should you run it for a while first? M
@TheDajoca3 жыл бұрын
Warm or cold. Leave for 10 mins after running, for the oil level to settle.
@amead774 жыл бұрын
jeebus f'ing christ, i spent ages looking for the oil filter on mine, expecting it to be an actual metal cased coke can sized filter. I felt like such an idiot when I gave up
@brikfiend3 жыл бұрын
Thanks M8 ,Did you used to demolish Chimney Stacks ;)
@doubleboost3 жыл бұрын
I Knew a bloke that did
@Emilio574 жыл бұрын
Me again, a bit of searching tinternet tells me the black carbon deposit is from leaking injector seals and will eventually kill the turbo if not fixed. Now to check the terms of the 3 months warranty!
@doubleboost4 жыл бұрын
Yes it is called the "black death" the carbon blocks the oil strainer , There is a filter in the turbo oil feed pipe that blocks up
@markhodson19454 жыл бұрын
What solvent do you use for washing the oil off?
@jusb10664 жыл бұрын
Looking like white spirit to me, he ran out of brake cleaner ? 😆
@doubleboost4 жыл бұрын
Brake cleaner
@Kielermatrosen Жыл бұрын
Und der blau Donau wird grau!
@flybobbie14493 жыл бұрын
Oil change 10k, i usually change 5k petrol or diesel. My old Peugeot 106 xnd i did 3k miles.
@TheDajoca3 жыл бұрын
3000 miles?
@flybobbie14493 жыл бұрын
@@TheDajoca Yes, cheap oil, car was on 156k miles when sold it, ran like sewing machine.
@ryanmg924 жыл бұрын
Careful on the new version of this engine, they changed the oil filter seal from square cut to round o ring, seen a few where garages haven't realised the motorfactor have sent the old style
@chilman64614 жыл бұрын
Thanks for that my one 09 square one
@TheMilford99 Жыл бұрын
Took my almost new, Peugeot Partner to " Carrera WORX " in Brentford, West London, they cracked the housing of oil filter, drove to Norfolk next day then discovered the leak, when i spoke to them they tried to blame me. I`m sure none of them are time served mechanics. Never again will i go to a greasebodgers garage.
@deanbeacom7563 жыл бұрын
Could you imagine this guy at your nice clean new car it would come back ready for the crusher never seen such a clatty mechanic
@bestpeter783 жыл бұрын
Oil is black and dirty just few minutes after put new one so...
@bestpeter783 жыл бұрын
Little hul... 😁😂
@Scotkruz Жыл бұрын
You left about 250ml in the sump...poor engine sump design
@jimsvideos72014 жыл бұрын
I've seen worse filter installations, but not many.
@mikeysgarage36974 жыл бұрын
Can't stand that style of oil filter myself, every one I've ever touched has been seized solid, as if they've been done up with an impact gun.