Thank you for actually teaching me something! I have a low idle on my f150. I've checked vacuum hoses, replace idle control valve and pcv valve. Cleaned the throttle body and still have problem. Cleaning the MAF sensor is my next move and I'm very happy to learn what to use and what NOT to use while cleaning the MAF! Thanks much!!❤❤
@jewelm39605 ай бұрын
Thank you! MUCH better than trying to find all that in a manual! 🙂 Well done!
@jwbranham20098 ай бұрын
Nice Video with just the right amount of explanation! Thanks for putting this together.
@grampadad Жыл бұрын
IT WORKED!! THANKS TONS!! But don't expect results until you drive it after cleaning....let it soak in with fresh gas (I used Seafoam and van started running rough after I used up half tank of the gas, and then I drove out the rest of the SF in the tank, refilled with new gas, and still rough acceleration until I drove it for a few min. then let it set overnight soaking....next day NO ISSUES!! SMOOTHE!! I read somewhere it takes a little while to let the fresh gas to wash off seafoam residue.
@randyoehlert95714 жыл бұрын
You should blow out the throttle body with compressed air after cleaning and use a lint free towel to clean it with the cleaner.
@victorcercone1909 Жыл бұрын
Ty it worked great
@hillarylies10973 жыл бұрын
Great video and very helpful. Keep it up man.
@seanjoyner66653 жыл бұрын
Thanks you
@gusacosta46552 ай бұрын
I felt like I was in your shoes doing this. I love the fact that you didn’t rush the video. I’ve learned more listening to you, than any other video dealing with the MAF sensor and you spoke in laymen terms. Thank you and enjoy the moment. 🙏
@montanawhite56996 жыл бұрын
Nice video, idk about that screwdriver tho.
@OzarksCreekandTimber6 жыл бұрын
Montana White gotta show old stubby some love every now and again. He spends a lot of time at the bottom of the toolbox lol
@pacny7 ай бұрын
99-04 5.4l 2 valve engine
@guywebster80182 жыл бұрын
Quick question on the other side of what you took off where yhe actual filter goes theres a hole on the side. Maybe two but it makes a wierd humming sound. Couldnt figure out where it was coming from. Are those holes supposed to be there? Im a rookie car fixer
@yosumamelendez12173 жыл бұрын
I'm sub just cuz you have a f250
@wendellharper19353 жыл бұрын
You should be able to clean that toothbrush with the throttle body cleaner and re use it to brush your teeth. Lol
@Jack-yw7bq Жыл бұрын
Does ur truck have a drive by wire or drive by cable?
@braxtonbragg11463 жыл бұрын
Why did it not start for a little bit? Mine does the same sometimes
@jamesfeeney28125 жыл бұрын
Thanks man. I love my v10 and this video was exactly what i needed to do. Got one on plug service??
@OzarksCreekandTimber5 жыл бұрын
Sorry man, I do not.
@jodieezell68212 жыл бұрын
If I pour it all in the intake and my motor won’t start what do I do
@bbjazzmanjazzman7721 Жыл бұрын
Check for smell of gas, if you keep trying to crank it, you should be smelling gasoline, if you don't then check fuel level, inline fuel filter and,or pump modulator..
@kletrain70794 жыл бұрын
Definitely have that shaky, hesitant, not wanting to go when putting the hammer down.