This is absolutley one of the most informative and straight-forward videos that I have seen on youtube. Thank you for making and posting it. I strongly agree with the many other viewers encouraging/requesting that you please continue to make and post future videos. A hearty "Well Done" from across-the-pond.

I always enjoy watching a pro at work. Well done sir!

Excellent video David, thanks very much. Just followed it word for word and mod done!!

Great to see someone who actually knows what he's doing. Sub'd.

thanks David --did this mod to both my dan wessons and worked perfectly. Great mod. Subscribed for more tips from the Doctor.

This is a brilliant video,it's the best way by far to power up this gun,please make more videos!

Very creative way to power it up a little place and 2 screws madness thanks for an idea

Pretty informative and professional way better than just sticking cardboard in anyway

brilliant,keep up the good work.looking forward to seeing more videos.thank you.

Dr. Gunsmith how am I only finding you now? You are exactly what I'm going to need when shit hits the FAN!

Awesome vid mate, I've just bought the umarex legends s25 version of this revolver.... at some point in the future I might up the power so this vid is excellent

awesome job, incredibly simple now that we see it here, thankyou

Just one question, and firstly thank you for this video! Will this work in increasing output power for the .177 pellet version as well?

Many thanks for the video dood. Very informative, Is it the same setup in the ASG Dan Wesson 715 6" Revolver? I would like to be able to tweak the power down slightly without running low power shells as these reduce the fps too much. My only other option is to drill out the centres of the low power shells to find a happy medium between the low and standard power. Thoughts?

This modification is great, but if you take off the co2 valve and open it and make the washer inside much thinner you get alot more power.

Thank you Dr Gunsmith

thx man the best tutorial i've found so far PS: I think it's a M4 screw

Brilliant! Thank you so much. Subscribed.

How much more velocity can this modification be expected to yield? Thanks!

Its a m4 nut and screw..but!! It does nothing to my pellet version ive screwed the screw in as far as it goes in and over my chronograph theres is absolutely no power increase 👍

david, hello. enjoyed your tune up video re dan wesson. i have a ruger super hawk 6mm co2 [8"] can i use this mod on my ruger, how far can you tighten the screw, is it a case of trial and error? what about the best type of bb's best to use? any more videos on this tune up subject coming up? thanks

its the same here in canada, our guns have "low flow" valves and no power adjustment

Perfect vid, thank you so much can u do one for the newer Dan Wesson 715 pellet version please

Nicely done, mate! How hard is it to fit the rifled barrel and where can you get it from? I need it for an 8" though.. Cheers!

Thanks for help i’ve been having a reoccurring issue where the hammer will not strike the gun or the fake firing pin to go off

OK...I just received my 2.5in Dan Wesson Pellet gun. With the barrel pointed down, I noticed there is an air gap between the cartridge and the little black seal on the rear of the frame...about the width of a pocket knife blade. If I push the cylinder back towards the hammer, the gap goes away. Do I have a defective airgun?

Hi David thank you for interesting video regarding in increasing the power of a CO pistol . Could the same mod be done to a Webly MK 6 CO revolver

I subscribeed, u seems to be a great pro...

There no fps test before and after So how do you know it works

Hello there, I live in the US and was hoping you could share your insight on cartage modification as their is no speed limit where I am.

What is the screw and bolt mm he uses when he tunes the power up? Please answer asap.

Is there a way to powerup a crosman vigilante? And would you use this powered up pellet for self defence?

Did you Chrono the Dan Wesson? I suspect that even with this modification it would only put the gun at around 3ft lb - Im in Durham with a Chrono if you would be interested in adding numbers to this video. Regards

two questions, this can not cause long-term damage to the weapon? and lose more gas than normal? that is, a bottle lasts 60 shots for example, will this modification decrease that amount? a greeting.

Any suggestion for where I can get the hex nut that is used to tighten the co2?

Hey there Mr Robinson can you please help me. I'm trying to increase the FPS on my Dan Wesson 8 inch revolver BB and I can't modify it due to its really, really tight screw. The last two that the handle covers are the ones that I'm having trouble with, which is kind of strange due to its size; I can bench press nearly 300 pounds ( so you can understand my frustrations), can you please tell me how I can unscrew them without damaging the gun or the screw?

So, that is basically the hammer spring we are screwing tight with the help of new nut and bolt. Right??

I know this is old now but great tutorial, what size screw/bolt please?

How exacly this mod works? And have you messured difference befor and after mod?

Hey, will this work on the asg 715 Dan Wesson 2.5 inch?

Will this also work on a crosman snr357? They look extremely similar.

Excellent video, whens the next installment??.. May I please request your next video is also a revolver.... :P I am getting the 2.5mm next week... any further info on these guns is greatly appreciated

now i know what i gonna do :) thanks alot !

Class Bro...

Should be effective and it is definitely interesting. However there are some cons to this method since all tuning is actualy a compromise isn't it. increased trigger pull weight which also increases the rate of wear upon the trigger bearing surfaces and finally increased co2 release /less shots per bulb. Still I might give it a go.

Great idea. I suggest to polish te "front surface" of the screw an apply some grease on it, so the aluminium "cup" wount wear too fast. By the way.. I just bought one and thinking of regrease it from factory greases. There is a problem because i dont know which oils/greases put on different surfaces. If You have some free time, please make the video about it. It will be sweet;-)

Cual eran las potencias antes y después de esta modificación ?

Great video thanks.

Hi Dave are you from the northeast GREAT VIDEO

I know this is an old post but I've found this very useful. I use mostly 6mm airsoft replicas and I'll try using this method to actually lower the fps in my Co2 revolvers. Do you know if other wingun revolvers have similar internals?

is there anything else we can do as ive done that mod with not a lot of improvement just uses gas a lot quicker

How can I get a hold of you for a few questions... I have the pellet and bb version.. cheers

More power thru the cap? Interesting 😊

I'm looking to get the newer Dan wesson, 715 - 4" barrel. Does anyone know of any good power mods for it?? Many thanks

thx, very good tutorial ;]

Is it the same modification for Umarex Legends S25 177 air revolver thst's the one I have?.

does this work on Ruger superhawk 8 co2 also ? :)

What type or screw and washer was used, size?

Great work.. Please make more videos. Also, How to power up schofield co2 revolver??

Use the shortest bolt you can or the head of the bolt will stop the grip fitting properly making it loose and rocky.

can you tell me how the rifle barrel worked out thanks

hi, I have a Dan Wesson CO2 6 inch 6mm BB pellets. you can upgrade it? if you like and where I can buy any spare parts? Thanks for all

hi thanks for this info . i have done the small nut on my dan wesson works great . is there anything i should do to the shells . thanks i know im 7 years late lol

Does anybody know where to get parts for these things at all. Mine dumps the co2 out nearly instantly. I cant find a replacement valve, or gasket kit anywhere. Theres no numbers stamped on the valve, no nothing. Any help would be appreciated.

9/32” (screw)bolt and nut fit perfectly in mine

By increasing the spring force, the trigger button also needs more force, and it will break before time!

Will you make video showing what you mean about the true 177 lead and the metal ones,you should make more vids your very good

Haven't done any modifications yet mine shoots 315 meters per second with a .40 gram airsoft bb totaling to 20 joules of power

Sorry iv not been on for a while as been ill for a while,but will be putting my custom Daystate Midas when I'm finished it that is.

Just got the Dan Wesson 715, is this mod the same with mine??

thanks bud, you sounds geordie? im from consett, and i see you have lots of extra cartridges, where would you advise me getting them? havnt actually bought the gun yet but ill need some extra cartridges.

Can you explain how to do the orther mods I.e Hammer sping and shells please

i live in the u.s.a. any chance i can get all the mods?

How can I get in touch with David Robinson - Gunsmith?

Do you do after dinner speaking?

is it possible to do a co2 leak fix videos for the dance weston

Does this work on dan wesson 715 4 inch

Great video and explanations! is there a possibility to put a gas canister that will be filled with air to turn it in to a pcp air gun? i'm thinking to replace the co2 cartridge and give it some more power. i have the ruger superhawk airsoft and i have replaced the inner barrel with a 60cm one(not for airsoft animore as it has too much speed) i use it for backyard target shooting

Hi great video , can you advise how to power up a sig p226 pellet blow back close sub 6 lbs uk

my powermod for ~40joules .177 is one drillbit and custom made round out of .22 lr shell.

It only makes it more consistent with the power

i hope you make some video of revolver shell modification to have higher fps

Can you do the same thing with the legends S25

I just did this mod. it was the easiest mod I've done yet. I added blue loktite to the exposed screws.

how can i get one of those preassure pins? i just fkd up one of mine :'c

It would be best , to.use a crono , to keep a eye on how much power the adjustment is improving too. Nice video

Can you make all of them more powerful

can we get this gun without a ukara ?

I whant do this to mine Ruger of Umarex its also a WG but its a 8 shooter instead of 6 and easy to load to, But i whant less power how i can do that the best weaker spring , its 360 Max in my country fore side-arms

Sorry about the Video cutting short as I was not finished but for some reason all of it did not load up,lol

thank you sir..

Hi mate if i travelled could you help me with. My Air Arms Prosport?

The nut and bolt are not going to give you more power to the air valve only to the trigger spring. By changing the rubber bb insert to the bottom of the cartridge you will have more power.

looking at the insides of this pistol we could all see the gas valve (it had a red strip across it), and it's the lowest power valve as only the low power valve has the red stripe, if you change this valve for the 8-inch barreled pistol valve, that has no red strip across it, that would bump up the power far more than pushing the hammer spring to its limit and in doing so you make the trigger pull much harder, however changing the gas valve come's at a price, but it's money well spent

This is the only Co2 I know of that you can do this with thanks for asking,and sorry for not getting back to you all,but I'm so busy at the moment and with my five kids I just don't get much time on here,thanks.

Looking towards owning one for defense without having to be scrutinized on the news :). Would leave a good dent before the box match :)

THX Man !!!

Would you sell a max power up modded one?

where you buy these guns

Thank you. I refer to your video