Link to Enlight LED Fog Lights: www.enlightauto.com/collectio...
Пікірлер: 35
@wermart82898 ай бұрын
I want to thank you for this video as i’ve spent 30 min figuring out why my fogs is not working after replacing bulb and checking fuse box and wiring but this video reminded me to check polarity of the bulb, it works 😂
@lomitanielu89624 жыл бұрын
If you had to use to screws to keep the front "bumper" in place and dont want to remove them, then you can access the bulb from underneath. A few screws hold the plastic cover under the car. This worked for me. Great video btw
@bluyllow4 жыл бұрын
Super helpful. Ran into the same problem with the screw fastener, and voila, came out just the way yours did. Thanks for the detail and time spent 🤘🏼
@bxpressiv2 жыл бұрын
Thanks, your video helped me work out how to get at my front parking sensor so I could pop it back in. Saved me $$$ I would have to pay my dealer for something that took 60 seconds to fix.
@sreekumarUSA2 жыл бұрын
112921/0121h PST. Thank you Bro. Appreciate your endeavor to exhibit installation of LED emitter to Camry. You did a great Job holdong camera in one hand and spreading the heat sink mesh with the other. Also the installation of the LED emitter into the holder. Thanks you several times. Take care and be safe.
@adnansyed57365 жыл бұрын
Thanks you saved me $60 dollars today
@harjindermandla19704 жыл бұрын
well explained without delaying. Thx
@swavovskyukrataen84257 жыл бұрын
great instructional video! thank you!
@JK-wn1dm2 жыл бұрын
Thank you for this video. I'm about to install a new LED fog lamp housing
@gquant17 жыл бұрын
Nice fog lights!
@tokki50245 жыл бұрын
thanks for video, it was great helpful !!
@droneinyemen53326 жыл бұрын
Thank you 🙏 For the video
@nacosnacos6 жыл бұрын
If you really want to get technical, the process of heat transfer (cooling) with these bulbs is RADIATION (solids to fluids) not CONVECTION (fluids to fluids). The Aluminum ribbons act like a radiator; they've added multiple ribbons to increase the heat transfer area. For removing the fender liner fasteners, you may want to consider using a mini pry bar rather than screwdriver/pliers - just like you were pointing out, in cold weather chances are you may damage any plastic part by force-banding it (including the fasteners) as it becomes brittle. Otherwise, nice instructional video.
@adnansyed57365 жыл бұрын
Do you have a video on changing high beam light to led
@killsoundpro4 жыл бұрын
Спасибо за видео !!!
@zaidalshammari79597 жыл бұрын
Do you guys have the switchback LED for the turn signal amber/DRL white in the front bumper for 2017 Camry SE?
@aamirkhanbaba1947 Жыл бұрын
Thank you
@hondak20z15 жыл бұрын
Are both the headlight and fog light H11?
@1999Shortstuff4 жыл бұрын
Replacing the fog light or fog light assembly is much easier by simply dropping the plastic drip-pan under the car (just a few 10MM screws). Messing with wheel well is just creating a potential problem since those wheel wells and plastic screws and clips are garbage and will easily break.
@sreekumarUSA2 жыл бұрын
Will try this technique. Thank you.
@jhshmid58197 жыл бұрын
ممتاز 👍❤
@hendriyahya79957 жыл бұрын
what brand the foglamp housing is? Valeo?
@alphaomega83734 жыл бұрын
7:05 he made a flower :D
@missmeyon3 жыл бұрын
@9:07 What does the module do?
@eurothrasher2823 Жыл бұрын
If you cut the wheels all the way to one side, turn to right for left side and fully left for the right side it will afford you a bit more wiggle room to get in there….
@danotero3027 жыл бұрын
i would rather zip tie the passenger side. sticking it to the wiper fluid reservoir not such a good idea especially if you have to one day replace the tank, you might forget and rip the wiring etc:
@recarnes713 жыл бұрын
They look nice but a lot of work for just two bulbs
@skydoosher7 жыл бұрын
H11 size, correct?
@Enlightautomotive7 жыл бұрын
Yes, H11 Bulb type.
@kenmorgan3163 жыл бұрын
This is the reason I won't buy a new Camry, I do not want to modify my own vehicle just to have fog lights. My 2015 Toyota Tacoma has some factory, get enough for me.
@andreholmessr54644 жыл бұрын
Next time show how they look at night
@TNKHART2 жыл бұрын
Too bad the link doesn't work
@batliff6 жыл бұрын
imo LED lights are too bright for fog lights.
@forcedhaircut5 жыл бұрын
James Bradley But halogen fog lights are fine, since halogens are dimmer than LEDs
@retiredat443 жыл бұрын
it wants to redirect my browser.... I was very interested, do not do that,, whomever put that scrip[t in! so wrong to push that on people!