Maximum speed

I'm fust as f*ck boyss!!!!!!!@@techshiva7671

Maybe one day...

Did you ever do it? I'm planning to do it because mine has a dead battery and it's pretty scratched and stuff and I no longer enjoy it.

At the time of building I had nothing suitable to extended the handle bars. The scooter seems to ride ok with the stock handle bars 👍

Thanks. I simply connected the brake wire to the relevant connections on the motor controller's. I have now improved on the electric brake, video is here - kzfaq.info/get/bejne/mq6Ee72rl7KWiIU.html

Laptop cells are rated for 2C. Most common cells are around 2200mAh so they can handle around 4.4A max continuous. Hoverboard motor power ranges from 150 to 350W, what our guy has here looks like a 250W motor. So with a 36V battery that would mean around 7-8A max, which is less than the 8,8A that two parallel laptop cells can supply. I still wouldn't recommend using laptop cells because salvaged cells rarely have full capacity. Also the cells in the pack might no longer be balanced in terms of capacity. But the guy made a pretty cool thing and now has something to improve, which is good.

I'm pretty sure that the battery controllers job to worry about

Top speed is roughly 8 - 10mph 👍 The existing hover board battery provides enough amps, however range could definitely be improved.

Hoverboards underpowered as hell I had a Jetson rave with 400 watt dual motors only 12 mph scary ass hoverboard that I'd smoke with my 16 mph bird air 250 watt single back wheel drive motor having scooter I was just reading volts are what effect speed of course with whatever watts your motor can handle being your limit idk how amps effect it but I woulda make it have more range and speed if I made one

Charger plug connector is wired directly to battery BMS 👍

The charger should be matched to the batteries voltage. Also the battery should have a BMS installed.

Y connected from one battery to two controllers using 3 pairs xt60 very simple

you maybe can but to be safe just use 1 controller for 1motor

@@willememmens9106 No, u can not do that. Do some research on the theme, i can not really explain more than this next few things: They will work on void, when there is no torque. ( so it will not work once u put it in the ground ) When there is a disturbance in one of the two motors, the controller will stop due to errors. And this errors will cause the motors to stop after a few seconds due to the controller not receiving the same magnetic electric charge.

They were attached to the brake wires on the motor controller. I have since upgraded to a mechanical disc brake. Please see my other video.

Super, thanks

Thanks 👍 Green throttle wire is simply split in a 'Y' to each controller.

I have read in the comments in another Utube that two hub motors, while can be controlled by one throttle, will have energy loss due to magnetic feedback. I wonder if you see this happening and if so, it doesn't bother you? how far can it go with one charge?

Correct. I wired the charger port directly to the battery output 👍 the hoverboard battery contains a BMS and I use the correct charger also.

@@robmakes8824 thanks, it helped so much , and one more thing is, should i wire positive to positive and negative to negative or pozitive to negative - negative to pozitive to charge the battery?

@@muratconay7548 positive to positive and negative to negative 👍

The controllers were purchased on eBay, however the listing is now no longer available.

Probably 20 km/h

And how far do you think it will go? For example, the xiaomi scooter has only one engine and runs 30km, at a speed of 25km/h.

@@nuggetczsk This has less range and no power to go up a ramp. It's a diy scooter. Can't expect much from it. And it's also not worth the effort, money and time invested in it. If you are good with electronics, you can buy some iphones 6 with broken glass, replace the original screen with chinese screen, also, buy some broken hooverboards, fix them, sell them and make 300 euros to buy a proper scooter. Or get a summer job at mcdonalds, make money and buy one of those long range powerful motors scooter. ✌️🛴

Speed is roughly 8 - 10mph 👍 Range could be improved with a larger capacity battery. Scooter has no trouble going up a ramp 😉

Roughly 8 - 10mph 👍

Top speed is roughly 8 - 10mph. I do not yet know the mileage per charge.

Roughly 8 - 10mph 👍

The motor can act as an electronic break

I have now improved on the electric brake, video is here - kzfaq.info/get/bejne/mq6Ee72rl7KWiIU.html

Yah same the wiring to the controllers got me 🧐

Battery and wheels are simply wired as per the controllers wiring diagrams. Red, black and green throttle wires are attached to first controller, green throttle wire is simply split in a 'Y' to the second controller 👍

Basically any switch will work on that method cuz these controller most of them use low brake levels wish works in the 4v or 5v system when u hit the "swtich" the brake it goes down to 0v and the controller sends message to the motor to brake. To Clarify Think about it as 2 cables + and - when u hit the switch the cables connect 0v and scooters brake.

I have now improved on the electric brake, video is here - kzfaq.info/get/bejne/mq6Ee72rl7KWiIU.html

Car boot sale 😉

All tools most people will find in their garage or shed 👍 ...apart from a welder perhaps

@@robmakes8824 yeah true, I don’t have the welder lol

Roughly 8 - 10mph 👍

Look above ive answered that question. Happy summer.

I copy from samir hanko's answer ..ehehe : 1 month agoBasically any switch will work on that method cuz these controller most of them use low brake levels wish works in the 4v or 5v system when u hit the "swtich" the brake it goes down to 0v and the controller sends message to the motor to brake. To Clarify Think about it as 2 cables + and - when u hit the switch the cables connect 0v and scooters brake.

I have now improved on the electric brake, video is here - kzfaq.info/get/bejne/mq6Ee72rl7KWiIU.html

There Is a pair of wires on the controller

I have now improved on the electric brake, video is here - kzfaq.info/get/bejne/mq6Ee72rl7KWiIU.html

Roughly 8 - 10mph 👍

I have now attached a disk brake. Please see my other videos 👍

What does the delta connection do? Im building a similar one

@@jvinsnes watch this might help you kzfaq.info/get/bejne/fr9ngtCk28u1ZWQ.html

pls watch this diy electric scooter kzfaq.info/get/bejne/fr9ngtCk28u1ZWQ.html

Roughly 8 - 10mph 👍

Please see my other video on my channel where I add a disc brake 👍