Dodge Stratus / Chrysler Sebring CV Axle Shaft Drive Shaft Removal and Replacement

Рет қаралды 132,048

Күн бұрын

Dodge Stratus / Chrysler Sebring CV Axle Shaft Drive Shaft Removal and Replacement!
► Our Website for Tools, Parts and more Videos: mechaniclifestyle.com
We took this video to show you how to remove and replace the CV axle / drive shaft on a Dodge Stratus Second Generation. It should be about the same procedure from 2001-2006 for the 2.4 and the 2.7 engine. It should also be about the same for the Chrysler Sebring from 2001-2006 since they are twin cars.
It is not very complicated procedure but you will need tools and some Penetrating Oil (Pb blaster) especially if you drive north. You suspension will have more rust so it is a good idea to soak them overnight. The easiest way to take the big nut that is in the middle of the hub is by using a Impact gun; however, if you do not have one you will need to have one person pushing the brake inside the vehicle and you will need a brake over bar and a big pipe for leverage.
It is about the same procedure for the passenger side as well.
It should work on:
2001 Dodge Stratus Left Right CV Axle 2.4 and 2.7 engine
2002 Dodge Stratus Left Right CV Axle 2.4 and 2.7 engine
2003 Dodge Stratus Left Right CV Axle 2.4 and 2.7 engine
2004 Dodge Stratus Left Right CV Axle 2.4 and 2.7 engine
2005 Dodge Stratus Left Right CV Axle 2.4 and 2.7 engine
2006 Dodge Stratus Left Right CV Axle 2.4 and 2.7 engine
2001 Chrysler Sebring Left Right CV Axle 2.4 and 2.7 engine
2002 Chrysler Sebring Left Right CV Axle 2.4 and 2.7 engine
2003 Chrysler Sebring Left Right CV Axle 2.4 and 2.7 engine
2004 Chrysler Sebring Left Right CV Axle 2.4 and 2.7 engine
2005 Chrysler Sebring Left Right CV Axle 2.4 and 2.7 engine
► 2ND Channel Subscribe: bit.ly/2a86p9Z
►►Honest Product Review Channel: bit.ly/2ygqUcy
► BMW E46 ZHP PROJECT bit.ly/2g8tOa9
► Ford Fiesta ST BUILD bit.ly/2a59UKp
► 2013 GT86 Project Playlist: bit.ly/2dz4xY1
Please LIKE & SUBSCRIBE for MORE DIY VIDEOS that Could SAVE YOU BIG $$$$$$$!!!
5 NEW VIDEOS EVERY WEEK!
Thank you!
*Disclaimer
We, World Mechanics, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not World Mechanics.

Пікірлер: 56

@WorldMechanics 5 жыл бұрын

⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzfaq.info/love/J9xpq0qUZevSEdBSFqO2ow ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys

@sovereignentity4924 3 жыл бұрын

Love his work and that accent too... 👌👍😄

@besnikvukaj3202 7 жыл бұрын

Great video, even better explanation. Straighforward and you made it very easy to follow the steps. I like how you didn't waste time. Thank you for your help guys. keep up the good work

@sovereignentity4924 3 жыл бұрын

Exactly the steps I needed to see to fix my 04/ Stratus... Thank you..! 🙏

@robertemmons2260 5 жыл бұрын

Thank you for your video demonstrating the procedures and tools. I knew most of the work necessary already, but the tool sizes and popping out the in board joint stub was a new one on me. Thank you!

@lmmooresc40 7 жыл бұрын

Thanks for sharing with us. Very helpful with my 04 stratus.

@AngelRodriguez-xj8vo 8 жыл бұрын

wow that was an excellent video. i am feeling relieved about doing the job. thanks.

@WorldMechanics 8 жыл бұрын

+Angel Rodriguez We are glad to hear that the video was helpful. Thank you for watching and if you ever have any question let us know

@DetroitSmash69 3 жыл бұрын

Wonderful video thank you brothers 💪🏼

@husseinalothman5564 Жыл бұрын

Thank you for this video clip. I am from Baghdad, and there are no backup tools here. I need a drive, I saw left and right

@Mehmet-uy8cr 8 жыл бұрын

nice. how come you dont have more viewers? you re doing an awesome job.

@carlosvega8932 7 жыл бұрын

ok after you had done all the work do you need to add more oil to the transmission

@terrycoe1602 5 жыл бұрын

how do you put the fluid back into the differential? Mine doesnt have a lug to check fluid level so i assume its through the transmission fill location, or is it somewhere else?

@vinniejohnson209 6 жыл бұрын

Hey ive got a question on my 2005 Dodge Durango I removing CV joint and the shaft stayed in the joint or axle so I had to remove it to be able to put it back in the differential without that shaft in there because the new differential already came with half shaft so once I took the CV shaft out that seal at the bottom the metal round piece that looks like a quarter I've been fed up the hammer in the champ out with us to divert now how do I get that back in there to help seal the grease in there or can I just go to parts store and replace just that small metal piece and does it supposed to stay put in that whole

@germangala6014 6 жыл бұрын

Do you have video how to remove the alternator of this car ?

@derickcaperton2814 8 жыл бұрын

Thanks! Makes it easy

@WorldMechanics 8 жыл бұрын

+Derick Caperton Glad that it was helpful! Thank you for watching us! We hope that you find other videos on our channel helpful as well!

@kamalabbady6778 8 жыл бұрын

thankyou brother for this helpfull video keep up

@WorldMechanics 8 жыл бұрын

+kamal abbady We are glad that the video was helpful. If you ever need help with your vehicle let us know you can also find us on Our Official Facebook Page here: facebook.com/worldmechanicsofficialpage/?fref=ts

@vernonsvendsen1300 5 жыл бұрын

Thankyou, if someone can't follow this video they shouldn't be working on a car.

@jondickson75 3 жыл бұрын

Thank you

@Balling_Out Жыл бұрын

Hey so I’m about to do this maintenance on my car and what do I do about the fluid leaking after I remove the cv joint. And do I have to replace it?

@chrisarroyo1975 7 жыл бұрын

I need help removing the CV axle on 2002 Chrysler Sebring coupe

@michaeledwards2919 Жыл бұрын

🎄🎄 Thank you so much for all your help I put a new driver's side axle on my 2004 Dodge intrepid, and those cluncks, and banging noises from underneath are gone. The rest of the front suspension is good. And I had the same problem, you pin-pointed exactly and correctly where the banging noises were coming from, the cv joints were broken, bearings gone, houses just dancing and clunking around in the old one. Thank you fine sir for you help🎄🎄☃️

@TURBOSHANE101 5 жыл бұрын

Should really use a torque wrench if you want that bearing to last.

@guesswhomartin9249 4 жыл бұрын

While looking at your video. All is great. However I've noticed, the upper ball joint is cracked, needs to be replaced as well. Although, I'm aware this video was on replacing the CV Axle Drive Shaft. great. Keep up the good work.

@jarrodmcmillian1747 7 жыл бұрын

same procedure for a rt coupe?

@richardmann5674 8 жыл бұрын

good video

@WorldMechanics 8 жыл бұрын

Great! Thank you! If you have any questions let us know.

@jakegroll7317 5 жыл бұрын

lol the wobble on those ball joints are gnarly..

@Ton908 6 жыл бұрын

The guy have three arms thats awesome

@ericalandipachecochan6478 7 жыл бұрын

porq mi estratus cuando paso un tope alto se holpea la parte de abajo seq las suspenciones estan vencidas

@jaycorrigal1207 5 жыл бұрын

hi just wondering does the transmission need to be in neutral before pulling out the axle?

@zachvoght894 4 жыл бұрын

Did anyone answer this

@cassielocke2519 2 жыл бұрын

Hey guys am changing the cv axle on my chrysler sebring 2005 2.4 convertable coupe and im having trouble finding the right axles to match the car all the ones I buy new seem no not be a perfect match. Unless the axles seem to be a new after market version that are adaptable to my car but even then it seems to be a bit longer by at most 3 inches

@donaldrollins3124 6 жыл бұрын

what if you follow your instructions and procedures and the cv joint breaks in half , and leaves the the inner cup still in the trans how to get it out what tool or ???????? Help!!!!!!!!!

@yatox8 8 жыл бұрын

So pro, don't even need to remove gold jewelry.

@knighttime19 7 жыл бұрын

Was piece of cake

@tanyaking8575 6 жыл бұрын

Nathan Scott y shit he getting the job done

@jeddavis6397 6 жыл бұрын

So kindly of you to recognize. Pros don't worry about that shit because there's pros. This is basic automechanics, not wood shop ya noob.

@guidosarducci3106 5 жыл бұрын

I also love the way that he uses the impact on the axle nut. 550ftlbs of torque is so much better than the 80ftlbs it SHOULD be torqued to. I love it when someone trashes wheel bearings cause they are ignorant.

@ameehasa5504 8 жыл бұрын

Just not clear how to use screw driver I hope describe it to me thank u

@lordvanhelz 7 жыл бұрын

what's up guys, great video!!! for the right side is the same procedure, or i need to do something else?

@GreyMK7Jet 7 жыл бұрын

i was in the process of doing this exact job for my sisters 05 Stratus hers is a 4 door and the autopart store provided us with an axle that has ABS any reason on why this happened? if all info was correct and knowing this car has no ABS?

@danrodrigues3531 7 ай бұрын

Apparently, you're not concerned about spilling transmission oil all over the ground.

@bradpitin1145 4 жыл бұрын

👍

@markmarcie2 8 жыл бұрын

Wow. Why are you removing the entire brake/hub arm assembly? It's almost like trying to get at the axle starting by going into the trunk and working through the dash.

@markmarcie2 8 жыл бұрын

+markmarcie2 What I am trying to say is your taking a lot of time to make the slide out/in convenient. You can do it without taking all that time.

@ramellbrown7265 7 жыл бұрын

markmarcie2