Here are some links to some of the parts I bought on Amazon. Unfortunately, the 85mm limiting straps are sold out. Hot Racing SPC3006 M3 Aluminum Standoff Spacer Set (4X)(2-4-6-8mm) www.amazon.com/dp/B00A1E5D3Y/ref=cm_sw_r_cp_api_i_Px7OEbP4KTQHC Hot Racing ERVT32C01 Aluminum Transmission Spur Gear Cover E-Revo 2 www.amazon.com/dp/B07LGH3RMM/ref=cm_sw_r_cp_api_i_gD7OEbWQNWFHP Hot Racing ERVT14X01 CNC 3D Aluminum Center Skid Plate. www.amazon.com/dp/B07MLY4WL3/ref=cm_sw_r_cp_api_i_-E7OEbV4BVN3X Hot Racing ERVT330R01 Aluminum Rear Bumper E-Revo 2.0 www.amazon.com/dp/B07K4R4W8T/ref=cm_sw_r_cp_api_i_aG7OEb9SDQPXJ Hot Racing ERVT330F01 Aluminum Front Bumper E-Revo 2.0 www.amazon.com/dp/B07K4PFPXS/ref=cm_sw_r_cp_api_i_UG7OEbAX5TWN8 Hot Racing ERVT331F01 Aluminum Front Skid Plate E-Revo 2.0 www.amazon.com/dp/B07HY7CQ8K/ref=cm_sw_r_cp_api_i_.H7OEbBB2046W Hot Racing ERVT331R01 Aluminum Rear Skid Plate E-Revo 2 www.amazon.com/dp/B07HY7X8VL/ref=cm_sw_r_cp_api_i_yI7OEb3HN4WFQ Traxxas 5632 Rear Chassis Brace (1/10 Summit, E-Revo) www.amazon.com/dp/B00N62UTAK/ref=cm_sw_r_cp_api_i_TJ7OEbZHX4QCR Traxxas 5446G Exo-Carbon Wing Revo www.amazon.com/dp/B000XQ5CJ0/ref=cm_sw_r_cp_api_i_GL7OEb05TA35G

Thank you Sir

Mike Gent No problem👍

Thanks😃. I recently installed Hot Racing shock springs front and rear and I think 🤔 I finally have this truck set up just the way I want it now.

Thanks🤗

They are suspension limiting straps. In stock form the E-Revo 2.0 will rip out shock rod ends when jumping it off large ramps. The tires are quite heavy in comparison to previous E-Revo’s and when the suspension drops down hard after exiting a ramp rod ends can work themselves out. You have to jump it quite high for this to happen though.

I pinned a comment that I replied to a while back above. All the upgrades and links to where I bought them are below his comment that I replied to. Hope this helps😁

I have a few RC screws kits from previous rigs I have had in the past, so I had longer screws on hand. I don’t remember the size, but they were definitely longer than the stock screws. Most hardware stores sell these types of screws though.

I used RC nitro fuel tubing for the rear bumper holes, since the rear LEDs were smaller than the front ones and wouldn’t stay in the holes.

Any hardware store should have longer screws. Here is a link to the Hot Racing spacer set I used. www.amazon.com/dp/B00A1E5D3Y/ref=cm_sw_r_cp_awdb_t1_ZU0IEb6T7FPRT

I've run it quite a bit. However, I have about 18 RCs between 1/24th to 1/7th scale and I don't run the same RC all the time. My E-Revo is my favorite rig, but I tend to take the Maxx out more, since it is easier to run due to it being smaller and only needing one battery. The ESC is still running fine. I run a fan on the motor as well as the stock ESC fan, which I am sure helps.

I found them on Amazon. The 85mm straps are out of stock, but they still have 90mm straps in stock. Here’s a link: Hot Racing SPC3006 M3 Aluminum... www.amazon.com/dp/B00A1E5D3Y?ref=ppx_pop_mob_ap_share Hot Racing SLS90T1111 Suspension Travel Limit Straps 90mm (Gunmetal)(2) www.amazon.com/dp/B0178GRMK4/ref=cm_sw_r_cp_api_i_r8XADb83S1BSY

I got them on Amazon. Unfortunately, Amazon is sold out of them.

Traxxas makes it as an optional accessory. A few scrapes on the rear of the wing from wheelies has revealed it is plastic underneath the carbon fiber though. It is a bit stronger than stock, but not much. It just looks cool😎.

🤔 Not really carbon fiber just painted like that. Had to drill my holes out a little and it was chipping. Nice looking though.

I bought it on amainhobbies.com. Here is some info on it: The Traxxas Revo wing is the latest addition to the performance accessory line-up for the six-time National Champion Revo 3.3. The combination of the adjustable deflection angle, wing height, and the unique wing design allow tuning options for any track condition and driving style. The wing is available separately in white, black or the new Exo-Carbon finish. (Exo-Carbon finish, includes decal sheet) NOTE: The Exo-Carbon finish wing is not made from Carbon Fiber material; it is a plastic wing with a carbon finish. This product is expected to become available for purchase on Thursday, July 1, 2021 Compatibility Traxxas E-Revo VXL 2.0 Traxxas Revo

No issues with the front yet😁

I like them a lot actually. The extra torque is really nice and it doesn’t hurt that they just look cool😁

Unfortunately, I don’t remember. I got lucky with some leftover RCscrew kits I had from other trucks. You can get these type of screws from most hardware stores though😁.

Yeah, I know. I was going to install them that way, but I have wires for my light kit running through there and Velcro is there for my Dynamite GPS speed meter. Where I have it does work and my shocks work just fine and there isn’t any binding. Plus, I did try to run it through the rear chassis brace, but the 98mm straps aren’t long enough. Thanks for the info though. I do appreciate you looking out😁👍🤗

Mark Santa Maria had the your way and they didn’t work, I have them threw the chassis brace and have cart wheeler bad and they work!

It has been. I’m just OCD about cleaning it after every run🤪.

Ah, you said it...85mm

It is the optional Traxxas wheelie bar with upgraded blue anodized aluminum wheelie bar wheels.

No I didn’t use the original screws. I have 3 different RC Screws stainless steel screw sets that I have acquired over the years, which definitely helped. If I didn’t have long enough screws hard ware stores work well too.

The part # is : Hot Racing SLS85T1801 Suspension Travel Limit Straps 85mm (2)

I used 85mm straps in the front and rear😁

@@beyondthebluerc1 i have the summit and the 85mm didn’t seem long enough i wonder is its a suspension difference with the two

@@chippytits3803 I am running the aluminum rear chassis brace, which may make a difference in how the straps fit on my rig.

@@beyondthebluerc1 yes me too same brace

@@chippytits3803 Hmmmm🤔 that’s strange. Not sure why it’s not working for you. Maybe you can run them through the center of the brace. I would run mine through there, but that is where I mount my GPS speed meter and I have wires routing through there for my light kit.

Amainhobbies 😁

@@beyondthebluerc1 thanks

No problem😁. I can’t remember exactly what size I used, but here is a link to where I found the spacers on Amazon. The kit includes 4 of each size 2, 4, 6 and 8mm. I just experimented with the different sizes until I got the fit I most preferred. Good luck and have fun with that E-Revo. It is one good looking rig and is a blast to drive. That suspension just soaks up rough terrain no matter how fast you are driving. Hot Racing SPC3006 M3 Aluminum... www.amazon.com/dp/B00A1E5D3Y?ref=ppx_pop_mob_ap_share

@@beyondthebluerc1 much appreciated my guy 🤙🏽

@@beyondthebluerc1 also I know you mentioned in your replies that you had longer screws from other rc's, do you know the correct name so I can search for them?

Shinobi_Absolute Oh yeah, those were old RC Screws stainless steel screw kits for an EMaxx and T-Maxx I had many years ago. Hardware stores sell these screws too. I have gone that route in the past, but got lucky and had just enough long screws in one of those kits to get the job done.