How would you modify this circuit to produce a faster rise in voltage, max(dV/dt), on the front side of the half wave?

Hello Ivo, I've been following your work for some time. I too have been researching the radiant energy effect, using standard axial coils of many designs. I've been at it since 2009.. I built a rather large, flat pancake coil using copper ribbon conductor in 2017. The copper dimensions are 6.35mm X 0.5mm thick. I used virgin teflon dimensioned at 12.7mm X 0.25mm thick as an insulator. It was wrapped as two, separate conductors, then terminated in the bifilar configuration. I did not build it as a Phi ratio coil, I didn't know about it at the time. The dimensions of the final coil are are 114mm I.D. X 265mm O.D. and weighs 2.16Kg. It's a whopper! I also put a 2.5 turn primary around the outside. The purpose of the construction was to investigate the original Tesla magnifying transformer configuration. I used spark and capacitive discharge excitation. This setup produced very high secondary voltages, even though secondary is only 84 turns total. But I changed course after experimenting with it for some months to exploring the mysteries of asymmetrical coils. I've been on that path for 4 years. I was fascinated at the incredibly high Q factors such configurations produced. But after a while, I found that the resonant 90 degree phase shift relationship that all those coils had accounted for virtually no useful power. They were all cosine coils and although fascinating, were not useful for power generation to any extent. I rediscovered your channel recently, and found the topic of stacked, pancake coils very interesting. Especially the use of speaker wire, which will produce electrostatic vectors in two directions. The standard radial field, 90 degrees to the magnetic field AND a field in phase with the magnetic vector. I built 3 smaller coils and used the Phi ration to set the ID and OD dimensions. All 3 are measuring the same to +/-0.3%. That is 115uH and 22nF as measured with my LCR meter at 100Khz. I am finding some of the same mysteries as you are posting. The dimensions of these coils are 57mm I.D. X 150mm O.D., wrapped with 16AWG speaker wire, which is very close to 1.5mm^ conductor. I would like to share pictures with you, but pictures cannot be posted here. If you are interested, an email I can be reached at is cpierce22@cox.net. Contact me and I'll send them your way. Thank you for re-igniting my passion about this investigation! I would also like to share what I am seeing about phase relationships and gain factors that are strangely high. You are free to post and share any info I share with you. I believe in the open source aspect of co-development.

Glad u take us through baby steps .

The best is yet to come. Happy New Year to all.

Incredibly, you are very persistent and inspiring! Good luck standing by your side!

Thank you for answering my last question to you. Wish you all good. 👍

I live the concepts you discuss! Keep up the great work!!

Best straightforward explanation I've ever heard. Thank you, Ivo, for your intense dedication to this research. You're the real deal. Thank you for your contribution.

Well done Ivo!! Thank you for your contribution. You offer an excellent foundation for us all which few are able to do...and that deserves some support. Keep up the good work. 🙏

Ivo your ability to explain clearly is OUTSTANDING! Bravo!

professionally done video, nice.

Congratulation! Very good! 👌 Come on guys, we have to support his work!!! 🤝

Great video Ivo! This is the most comprehensive video that I've seen you make so far. I like how you showed that you can redirect the back EMF Spike from the coil. I think that was the key to what Ed gray was doing with splitting the positive. It's the same thing I attempt to portray in my resonant charging video. The higher the frequency the more you're going to get coupling to the vacuum to produce the spikes. Nikola Tesla said that you need at least 10000 cycles per second to get the secondary parts of the energy out. You can see in my demonstrations that I use capacitor discharges along with the wireless energy discharge that's occurring at the same time. You can basically recharge your system while at the same time powering a load. By producing the wireless resonant field of energy which can be tapped into by multiple receivers not just one. Because it is a scalar energy field it can be into at multiple points without draining the input power. This part is free. Additionally you can use the pulses to power light bulbs and electric motors. This way you can put more energy into the system than what you are using. The higher the frequency, the more power you can get out of the circuits interaction with The Ether. Glad to see that you are growing and learning with your experiments. And glad to see that you are freely sharing this with us. I will do what I can to support you from here.

Good work! Thank you Ivo. Happy New Year!

Wonderful explanation, thank you for sharing

Thank you for this video.

Love you Ivo 😁🦊🤩 Keep It up!!! We support you my friend!!!

Excellent explanation.

Hi Ivo As usual, very fascinating work. PayPal on the way for Christmas coffee Happy holidays Can’t wait to see the next step. Thanks brother

The love that you live is always the love that you give

Good job Ivo

Very well done!

Wonderbar !

Now your talking, this is real experimenting with step by step advancements. Only 6 watts drain, I can see where this is going. Looking forward to your next video. Regards... DC

Very interesting video.. I've been using a similar method across the output of a few of my low input charging Oscillators & I've been able to hit COP 1.0 with 5 of them but they're not accessing the types of voltages your used to playing with.. I'm using a solid state relay with them. I'm using just two 3.7v Lithium Ion Batteries.. Very interesting video. I never thought of doing it like you explained... You explain it very well..

Great Video! Can you comment on how the Edwin Gray motor utilized DC Impulses to recharge the source battery? It seems like impulse technology is the basis of most OU inventions.

That is very good video. I have to questions. 1. Hiw we van regulate the frequency of those impulses in order to match the resonant frequency of the source we want to kick start. 2. Can we use just a signal generator PWM to create those Unipolar impulses instead of this circuit?

Amazing work, and so clearly explained!! Now ... where to from here?

Nice video and nice work Ivo. Thank you as always for sharing your insights and passion. Do you have a gut feeling as to how close you may be to being able to get work out of this such we see more measurable output work than in? Right now I have this sense that you are very close, but there is something just not quite clicking, so to speak...

Very, very good!!

Thanks! How is a coil generating a stronger or equal pulse than a Capacitor if the magnetic field is slower than the dielectric field?

Sweet!!!

Hello sir. I just wanted to thank you for poeting these videos. I did have one question: im a novice when it comes to electricity so much of this new new to me. Even the basics. But im trying to pick it all up quickly like my life depended on it. Do you have any suggestions that may help my endeavors? I madevall the coils barring perhaps some errors but i have an understanding of the functionality and concepts. I actually really enjoy learning this. One of my problems is i got to a point where my fear is preventing me from taking further steps to achieve what i think are mt target goals for my project. As much as i like this i dont want to be a statistic of an electrical mishap but i dont like harboring the fear. Despite current events i keep procrastinating myself into some idealistic rendition of the future. Im almost on the verge of a neevous break down lol. Thank you again for your posts. I will do my best to donate to you soon as i feel your research is godsent and i appreciate it.

As per your diagram at 7:03, you are wrong. At the end of the coil, where the MOSFET(high side switch) is connected, the coil discharge pulse will be Negative, the opposite of what charged it. So, the body diode and the MOSFET will bock it actually. To effectively extract this inductive spike, you need to have permanently connected reverse biased, high speed diodes at both ends of the coil, connected to the capacitor, which is also connected to the diodes in the proper polarity, which can be further switched out for the required purpose.

Thanks

Thanks for this valuable contribution to further Tesla's work on Radiant Energy Technology. You are a Master Teacher, Ivo. 70,000 impulses per second is too high for my application. I want to use your circuit to generate Impulses for a Motor. Is there a way to control the frequency and duration of the Impulses as needed?

I think it won't charge the cap until you let the coil ring. The BEMF is always opposite to the supplied voltage therefore every single inductive spike produced will not goes to the cap but to the load if there is any...that is due to the reverse bias of the diode(body diode). And if you let it ring the load and the cap will share the power produced half in each cycle of the wave till it completely dampend. Since you intensionally removed the ringing effect all power(from inductive spike) will goes to your pickup coil/extra coil. Keep it up bro and thanks for sharing such a nice topic.

Hey Master! Thanks for your kind effort. I think the diod directions seems need to be reversed in some of the schematics by the way may be Im wrong. all in all Very nice explained👌👌

Nice work! I am experimenting with Kenneth Shoulder’s exotic vacuum objects which are produced with 2 kV impulses to a cathode. I need to limit the impulses down to a fraction of a nanosecond. Any ideas on how to accomplish this? Thanks for your generous contribution to the field.

Thank you for your insights. Only problem I have is that you compared input WATTAGE(VxI) to just your output pulsed voltage when you tried to prove efficiency

Great Job Ivo! Now you can generate unipolar HV impulses at will. I'm wandering is it possible to obtain any peculiar electrical effects when reaching 1us impulse duration as described in the book mentioned in your previous videos. BR

Hello master Ivo. I'm an electronics newbie and your explanation is great. You cleared many misconceptions in my head, and your work encouraged me to work on Tesla negative impulse as well but, since I'm a newbie, I prefer working on low voltage first so.. working with 2n2222 transistor, but I'm not sure how to position the diode since, like you explained, it doesn't have internal body diode. Thank you in advance ❤️ Oh another question, from Don Smith work, he said lowering the frequency of a coil could be established by adding a resistor, in other area of his speech, by adding a capacitor, just like you did in other videos. I wanna know when to use either ones? I have lot of questions actually but that's for now. Thank you again and keep the great work!

Hey again Ivo, wondering do you have a build list of all parts and tools used? Getting into this stuff, I'm not always sure if there are specific reasons for some of the other things you use. You explain the circuit really well, but are there other things to look into, like brand specific mosfets or bad power supplies to stay away from? I don't want to waste money on things I might not need or things I need that I skip out on due to finances. Thanks!

Awesome IVo. Thank you. Question: Can we use both high and low-side impulse circuits on the same battery to use both positive and negative impulses to power something else? 2nd: Could we save more battery energy with higher kilocycles or lower kilocycles?

I think I get it. You are going for the one wire system? Square wave @ 1-2 million per minute is where the magic starts, as I read it in tesla’s prose. Is it possible to get this kind of frequency with what circuitry available out there now? If not, I guess I am sticking with doing a wheel added to the center shaft of a Tesla turbine, with 100 or so tungsten pins, quenched gap. It won’t have all the fancy circuitry, but with a turbine @ 50-80k RPM it is possible to get to those frequencies.

Ac isn't required to get longitudinal impulses? Just quick switches to interupt the formation of the magnet field i.e longitudinal waves i.e dielectric fields or tesla radiant energy?

When a current flows through a coil a magnetic field is produced. If two windings are wound together and a current flows through each but with one in the opposite direction there will be no magnetic field. The impulse is used to cancel the magnetic field and even drive it into the opposite polarity if one circuit has greater ampere turns than the other. Only wire resistance is seen and large currents flow. As the magnetic field intensity between the two windings increases the currents stop with high voltage. A secondary that is tuned to atmospheric electricity will exhibit a tendency to resonate and a small current will flow to earth. The low intensity magnetic field will change ever so slightly and will have polarity changes. If the primary is intermittently pulsed with a large current of exact timing the magnetic field will change polarity and produce a huge instantaneous current to flow in each half wave. A test can be done on a transformer that shows the link between two windings an input and output is DC equivalent to only 1/2500th of the load. The DC current in the 1350 turns of the 230volt input winding that produces the magnetic field of an 80 watt transformer is 0.9volt X 0.035 amp = 0.032 watt. The ampere turns are about 47.25, 1350t X 0.035 amp. When the opposite ampere turns of the primary exceed the ampere turns of the secondary the result is a reversal of the magnetic field polarity.

could you use this method from mains power as supply how would that circuitry be implemented like instead of a battery or power supply straight 120ac from a outlet and do you have videos of basic electrical theory for us total beginners

Could it be that positive impulses interact with the positron and negative impulses with the electron? Weber talked about a positron based nuclear model...

Hello, I wonder when you use the energy of the capacitor that stores negative energy of high voltage, which is in parallel to the battery, when it re-osilates in the next cycle the coil does not extract energy from the capacitor but from the battery, due to the lower impedances of the battery, the capacitor was charged with little joules, and it is not enough to feed the coil, it is only a configuration problem, ok thanks

1.Will this circuit keep producing the impulse without losses? If yes, will the impulse production maintain itself while steady power is being drawn from it if the coil in this circuit could be made resonant with a conventional transformer?

in the demonstration is that set up high side switching or low side switching?

Are bifiller coils ever very useful as capacitors in DC systems?

Hello, good time. Got, returns to traditional circuits, right ?? Please send a circuit plan.? Thank you.

Is the output frequency limited by the mosfets speed or the phenomena itself?

hello, awesome video! where can I get those circuits shown at 1:50?

It seem's to have a lot in common with Bedini circuit or jewel thief circuit . You Have achieve more than tesla. Only if you understand the basic can you truly find all the hidden energies the universe has to offer. Look into reversing coil's and caduceus coil even more remarkable result. Happy New year I new you would get in. much small design and higher efficiency . Peace and best wishes to all.

This is amazing, very clearly explained for anyone to understand. Commercial equipment that produces high voltage pulses is too expensive for a hobbyist. I am looking for an amplifier that can produce high voltage pulses up to 1000V at frequencies ranging continuously from 0 - 4MHz. This is to power a Rife plasma bulb for healing. I thought of getting a retro AM tube amplifier made for this purpose similar to what R.Rife had used originally. But this method seems to be far easier if it can produce a range of frequencies and also put out about 500 W.

Ivo, is there any possibility that you can sell me one of your finished Impulse plates and you could send it to Chile? I would love to be able to test this circuit in some of my experiments. thanks in advance J. Lezana

Sorry 4 the silly question, what about using a spark gap as switch? Great video and researches though!

What will happen if you put the coils in to liquid nitrogen to make it a super conductor? Maybe the dielectric resonance will go on for longer or continue since there is less heat & resistance in the system.

hi brother i have some questions on my mind, is there many different energy style i mean radiant energy organe energy scalar energy cosmic energy and so on, do u guys thinking its all the same energy or different? and i know the scalar energy is giving us healing force, many secrets behind of them i am searching many years thats enegy and secrets behind them.so guys any idea about thats?

Hi Master Ivo. I need an advice on a Lakhovsky MWO. I have made some versions and I am interested in couple things. 1. How can I measure all the frequencies coming out of the antennas? 2. I have added a 13th outer antenna with 18.1mm diametar hopkng to produce lower frequencies (like on a bass guitar). Btw, I am not an engineer. Many thanks. And if the comment is not suitable for the chat thread, please remove it. I could not find other way of contact. Many thanks in advance. My name is Robert Netkovski

What happens if instead of opening the circuit, you switch the resulted pulse to another coil?

Isn't the principle here same as that used in lighting up a fluorescent tube?

Can we purchase from you a circus like this in the video but instead of 70Khz to be able to move between 3Mhz and 12MHz fir example, because in this bandwidth are the resonant frequencies of our resonator.

Does Mosfet cycle at 70kcycles ?

Breakzeitgeist channel for HPR

Is it possible for 1-2 million frequency?

Can you tell us if there really is free energy that comes from the environment?

At 7:50 the text is upside dow

Y la antigravedad.