EP#15 Honda ATV Rear Differential rebuild.

No video

EP#15 Honda ATV Rear Differential rebuild.

Рет қаралды 95,904

PowerModz

Күн бұрын

Installed this rebuild kit available at www.powermodz.com
Easy install!

Пікірлер: 49

@tryingfirebird6119 9 ай бұрын

Been wanting to check my backlash, this is the closest video I can get to get an understanding of what to look for, service manual is coming in clutch right now

@rhess107 3 жыл бұрын

I keep a toaster oven in my shop. Bake cases at 350 for 15 mins and bearings usually drop in. Heat bearing and the slide on, like the pinion gear. Always keep some tools nearby to "drive it home" of necessary. Also, a bit of water based wire lubricant on the outer rim of the seals helps them to slide in and it evaporates. Great tip on the box tubing tool!!

@PowerModzOfficial 3 жыл бұрын

Great tip!

@joseph.g8792 4 жыл бұрын

Currently doing my 2001 foreman 450 rear end thanks for the vid👍👍 very helpful Doing the piston rings and head too 😂

@jackarseneault956 5 жыл бұрын

Thanks for the info and your time.

@HardAiims 5 жыл бұрын

Get that indy lite going! And we wanna see the XLT

@craigr6763 5 жыл бұрын

I think you need a work bench my friend!

@mikeraftis6332 Жыл бұрын

Red lock tight instead of staking bearing nut. Use Threebond instead of silicone.

@juansantana4533 2 жыл бұрын

Buen video señor thanks

@stacyreid5077 5 жыл бұрын

Where you heated the rear end case I was taught to put the bearings in the cooler or refrigerator for a while to shrink it where as you heated the rear to expand it

@PowerModzOfficial 5 жыл бұрын

yes we did that - youll see in other vids

@masondick4851 5 жыл бұрын

He did both.

@stacyreid5077 5 жыл бұрын

I must've missed those somehow. Thank y'all both for heads upping me

@gdwmnlvr850 5 ай бұрын

Hope none just watch this and start. I've seen others about the needle bearing removal on a Foreman 😂

@robsoncarvalho13 2 ай бұрын

Bom dia amigo Qual ferramenta para trocar o rolamento do pinhão parece uma porca estrela. Sabe dizer o nome dessa ferramenta por gentileza

@rickeyroberts9812 Жыл бұрын

How did u get original pinion needle bering out

@kartboarder22g17 5 жыл бұрын

No differential in quads, didn't know that.

@peter12266 4 жыл бұрын

Whats the trick to getting that internal C clip in on the needle bearing for the pinion

@jodyprice420 3 жыл бұрын

I no right i broke 2 wich my housings is not in best shape. Last one i did some of the clip broke out and sone stayed in. We going to try it. In process now putting back together

@juanandresruizlondono4012 Жыл бұрын

Hola cómo estás necesito una de esas

@stevenlonien7857 4 жыл бұрын

Whoops should. Only use brass hammers , colledge. Classes 101

@mustangman4186 3 жыл бұрын

How has the rear differential been for you with the grease in it?

@BigDaddyPain 4 жыл бұрын

what was the sizes of the ring gear spacers?

@brienwright 5 жыл бұрын

You need a work bench!

@TheOldBailey4135 3 жыл бұрын

Why not start from the beginning?

@hsvkidusa 5 жыл бұрын

Question about the zerk fitting. Are you going to absolutely FILL it with grease after you put the gear oil in? Like a bushing? you mentioned that you were going to fill the case with grease, but you also mentioned about making a slurry.

@PowerModzOfficial 5 жыл бұрын

I put some gear Lube in and then topped it with grease - I wanted to make sure the gear lube hit all the bearings.

@hsvkidusa 5 жыл бұрын

@@PowerModzOfficial interesting. Obviously speed is not an issue, but getting up 10, 12, 15mph.. how much resistance will that be? as things warm up and expand, as it goes up to the vent tube, will it introduce air and froth?

@PowerModzOfficial 5 жыл бұрын

@@hsvkidusa no issues

@xtidnab 5 жыл бұрын

lets work on sleds, season fast approaching, maybe leak down tests

@Calebmcguckin 5 жыл бұрын

If you ever need to replace the swing arm bearings on your TRX 300 make a video on that.

@zacharyknepp4094 3 жыл бұрын

Where can I get a ring and pinion for a 85 fourtrax 250?

@juanandresruizlondono4012 Жыл бұрын

Hola buenas tardes. Nececito una de esas

@jessicablack8476 3 жыл бұрын

Do you have a video of you taking out the pinion needle bearing?

@PowerModzOfficial 3 жыл бұрын

I dont think so sorry

@remypaquin7224 2 жыл бұрын

Been contemplating this fix for a while because I seem to have develop a leak at my rear output shaft (hopefully from the diff side) and may want to rebuild diff while at it. In any case to remove that bearing a old millwright trick you can use is small scrap of linen covered in thick grease. Put those scrap in the bearing ID hole and use a press with a blank peice of round stock as close to the id hole size as possible. The grease will work itself under the bearing slowly push it out. Keep adding linen with grease until its out. If you want to go full redneck bread can also work. ( great trick for getting beer cases from friends with bearing issues) Now for driving it home I would avoid differential heating and would go the oven route if possible. There also pdf version of a Honda repair manual floating online for these bike in that you can get the size of the bearing pushing pressing tools you need. Then if you have access to lathe or machinist friend you can make you own. These are better and safer. I made my pushed with a small pilot hole so that they can all be used with an extension that i made ( can also be used with a hammer if in an emergency) If they are machined properly they should pilot onto the bearing and only push on the outer race of the bearing( never press the inner race of a bearing unless you want to pre fuck it and replace it often).. Apologies for long winded awnser

@imurk9034 4 жыл бұрын

Question. I just inherited a 95 300 and its front wheel drive lol. I'm wanting to fix the rear end but I dont hear any grinding or clunking of gears. What would you do?

@ildxnnyli5541 4 жыл бұрын

Do you still have this issue? I'm guessing not

@imurk9034 4 жыл бұрын

@@ildxnnyli5541 yes. I havent fixed it or driven it since.

@ildxnnyli5541 4 жыл бұрын

@@imurk9034 want me to help you?