Pt.2 Honda TRX300 Final Drive Rebuild At D-Ray's Shop

Рет қаралды 106,551

8 жыл бұрын

Moving right along..... removing all the old bearings, and cleaning the cases. In the next video, we'll begin pressing in all the new bearings. Thanks for watchin'!
Stay tuned........
Here is the link to a video I made about my blast cabinet.
• Self Contained Blast C...
I created this video and I own all rights to all content in the video.
Music provided by : Kevin MacLeod incompetech.com/m/c/royalty-fr...
Name of tune "Cold Funk" Kevin MacLeod (incompetech.com) Licensed under Creative Commons "Attribution 3.0" creativecommons.org/licenses/b...
Music provided by : Jason Shaw://audionautix.com
Name of tune "Throwdown" Jason Shaw (audionautix.com) Licensed under Creative Commons "Attribution 3.0" creativecommons.org/licenses/b...

Пікірлер: 40

@mechanicmike2858 6 жыл бұрын

I know this video is a couple years old but I just want to say thank you I appreciate you taking the time and explaining these repairs in a simple manner thanks a lot

@RednecksGoneWild 8 жыл бұрын

Put a new water pump in my 93 Mariner 40 today , Just wanted to sat Thanks for the videos, Helped alot.THANKS

@theodoremcadow3070 3 жыл бұрын

Ive got a 85 big red 250es that has the exact same final drive, this video absolutely helped me get mine rebuilt.

@elvisream3322 6 жыл бұрын

My free honda trx 300 fw is in poor condition thank you for the videos saved me a lot of hit and miss thank again

@curtwynkoop6085 5 жыл бұрын

Awesome information and technique on this project ! It will help me on my atv.

@paulcarpenter7429 6 жыл бұрын

Great Video D-ray. Have done lots of 300 final drives. I found that if you work the spring clip around to an open end you can hook it and pull it right out. Then I use an inside bearing puller with slide hammer. Heat case a little with propane. Pinion bearing will come right out. On installing new pinion bear I never reinstall the spring wire. There is no need too as the inside nut will keep it all together. On a final note, I sometime use a speedy sleeve on the crown gear were the seals run because they are usually well grooved and over time will let water back in. Was a very poor design in my opinion from Honda. Keep up the good work.

@larrygreen2831 4 жыл бұрын

I just did both my Honda 420s. I was able to remove the pinion pilot bearing retainer as well through the hole. then use a expandible bearing slide hammer to remove the bearing. I opted not to reinstall the bearing without that bastard wire lock, its a tight fit anyway! Hope this helps!

@roberthowse6337 8 жыл бұрын

Great Job. I really like to see you do stuff like this, The Explanations are Exceptional.

@mc8305 2 жыл бұрын

Nice videos and I like the custom tool ya made that’s a good idea thanks for sharing

@dennisdyg2887 10 ай бұрын

Thanks, good, informative video

@dieselpoop 8 жыл бұрын

very cool d ray excellent job as always!!!

@SteveRobReviews 8 жыл бұрын

Now that was slick. 👍👍

@dangolden5696 7 жыл бұрын

Great video series thanks so much! really helped with my final drive rebuild. Turned out perfect. but did take some time. Thanks again!

@tomclark3592 4 жыл бұрын

Dam good teacher! Great quad side manner.

@jayschwartzenburg4708 7 жыл бұрын

Thanks great video helped so much!

@Joe-tz3un 3 жыл бұрын

Thanks for the information

@RonaldHambrick 8 жыл бұрын

Special tools? We don't need no special tools! We make 'em ourself!

@liddell157 8 жыл бұрын

I'm glad your back making videos

@charlesgrady7189 6 жыл бұрын

Hot wemon

@charlesgrady7189 6 жыл бұрын

liddell157 and

@charlesgrady7189 6 жыл бұрын

Milf

@charlesgrady7189 6 жыл бұрын

Milf

@ericneering6357 2 жыл бұрын

I’ve done it twice now without drilling a hole you need a really long and skinny skinny drift punch

@zozimodelacruz4062 4 жыл бұрын

MUY BUENO - DIDACTICO

@zx8401ztv 8 жыл бұрын

Hey your tool was a good idea, i suppose if it was a more regular job you could get a bigger diameter bolt and file the end to fit the ark of the bearing outer. Full contact between the end of the bolt and locking ring may make it a bit easyer :-)

@MrRbt61 6 жыл бұрын

work clip around -find end - hook up - pull with pliers

@JOCO1911 5 жыл бұрын

Would you happen to know if the rear axle bearings are the same size as the front?

@misticheeks9892 8 жыл бұрын

HI, It's me again. thanks for your video's. I am working on my '96 honda 300 as we speak and I have the 2 bearings & seals for the case, but UNFORTUNATELY it turns out its my pinion bearing. (my luck) Just wondering if u may know the # or the dimensions for the pinion bearing I need? I am learning alot from you & just wanna say Thank You So Much!

@gadsdenviper7149 6 жыл бұрын

I normally take a carbide bur and cut the race in 2 and the pieces fall out.

@nickchialOG 6 жыл бұрын

Gadsden Viper your suggestion was a life saver great tip!

@chrisshepherd4786 4 жыл бұрын

i have a 95 honda 300 it runs but cant get it to pull , ive put new clutches all new rear end parts pinion gear and u_joint but cant get the shaft insicde the motor block the one that turns the drive line to turn and i dont whats wrong wth it im not that of a mechanic ..asking for some pointers on mite wrong wth it ,,,,thx

@shelbygraham1795 2 жыл бұрын

I'm doin a rebuild on a 85 big red that little bearing on mine there is not hole it's got a circle but no hole where Iyou can see a circlip do I need to drill a hole down to a circlip or is there one on this year?

@shelbygraham1795 2 жыл бұрын

5 mins into this video it talks about it