In this video I go over the symptoms associated with Transmission Control Module failing internally. Check Grounds First see here- • Ford Focus & Fiesta Mu... Check me out on Facebook- / 651813524932940
Пікірлер: 428
@DripofHunn10 жыл бұрын
Thank you for taking the time and posting these videos. Which I had known about your youtube channel before I bought my Focus.
@EagDesert7 жыл бұрын
What if you have a new TCM and new clutch pack in a 2013 and still have bad trans performance, loss of power, overheating trans, etc? What could be the problem?
@Rich93514 жыл бұрын
Do you have any how to videos on how to go change a TCM on a 2013 Ford Focus SE? Or do you know what to do after you swap out the TCM for a newer one? Is it the TCM Adaptive Relearn service? Thanks
@lacarlousjackson84 жыл бұрын
Thanks a lot I just brought me 2012 focus SE and got it service today and he told me about the TMC. Thank God it’s not over 1000.000 cause i Got nervous like hell. Thank you for the video man
@RKCorinth3 жыл бұрын
Old comment but curious as to if you still have the car or not and what problems you may have had with the car along the way
@lacarlousjackson83 жыл бұрын
@@RKCorinth I still have the same car. Had a recalled computer that deals with the transmission...still sitting in the yard need a good clean up. 😆
@GunnerGomez2 жыл бұрын
hi brian can i ask you a question about my clutch on my 2015 ford fiesta? its a long one!
@philh92389 жыл бұрын
just did one on a 2014 fiesta. had the control module performance code, and u0101 lost com with tcm. it caused a no start issue though. no shifting issue, when i turned the key on to read codes the trans clutches would be shuttering for a minute or so.
@johnnydeep10516 жыл бұрын
HI Brian Good Day, Can you help me with my 2011 ford fiesta 1.6L A/T. I encountered this while i'm driving going to work. When I tried to step on the accelerator the car is not responding, i thought i was in neutral.I tried to park it and it responded again. As I started the car, Check Engine Light appeared. I scan it using my OBD2 scanner and the error is P087A(Clutch position sensor B - circuit malfunction). I tried to reset the faults and everything, It was cleared and i test drive it. It run smoothly for about 30 minutes, then all of a sudden the transmission disengages again,while stepping on the gas nothing happened, i tried to slow down by stepping on the brakes and stopped completely and the transmission engages back again, i parked the car and do reverse and nothing happened. I tried to run the vehicle again so I can go back home and it runs smoothly with Drive position and then when i turned off engine and started it again,Check Engine Light appeared again and car was now in Limp Mode. I've noticed when the car's temperature is fresh off the start it runs smoothly,and then problems start to arise as the engine temperature started to build up. What can you advise me with this problem? I hope you can help me with this.More power on you and your page. Many thanks.
@williammasterson103010 жыл бұрын
I think I had the same issue tonight as I was about to drive home from dinner... I just hit 91k miles (I drive about 100 miles a day round trip to work). Since day one of having the car (March 2011), I've always had grinding issues with the trans shifting from 1st to 2nd, and then tonight I had all of the issues with the cluster 'going wacko', and unable to shift out of park, requiring full restart of the car (four times). VIN: 3FADP4EJ6BM122146 Should it still be able to be repaired 'under warranty'? and if so, what's the bulletin number so i can bring it up with the guys at my local shop?
@TheRock02328 жыл бұрын
I have had two go bad in my 2011 already. What is different from 2011 transmissions to newer ones that they will not interchange? Is it a physical difference or electronic control?Thanks, Rocky
@galacticwarrior6 жыл бұрын
I'm no longer covered under the bumper to bumper warranty, I should still be covered under the powertrain warranty right?
@isrraelantoniojarquingomez52967 жыл бұрын
hello friend i have a focus 2012 change tcm and double cluch but do not let me calibrate drum and cluch you know if the gears of the drump have be synchronized when installing tcm module
@damor79397 жыл бұрын
i have problem on fiesta 2014.. they automatic transmision always failure... need to help for consultation ?.. thanks gbu
@blutorlz37 жыл бұрын
How common is it to have the loss of acceleration issue without any DTCs? I have had to pull over to the side of the road twice now. My car has been at the dealer two times and they say they cannot replicate it and no codes. They seem unwilling to do anything now. When this happens, my caronly revs and the shift selector display acts strange. The blue indicator light will only show on park, reverse, neutral, and drive. The light will not show on the sport mode, when it normal does.
@gmztecnologia7 жыл бұрын
I have a transmission in my shop that has the P2831 - P2832 - P287B trouble codes. I have tried to reprogram using Forscan and doesn't complete the learning procedure, is there a mechanical problem with the transmission? It's the first time i had one of these in my hands and i'm lost...
@techiapas47177 жыл бұрын
hi how yuo doing i have a question if a change a dsg module for ford focus 2012 for a new one do i have to have a motorcraft acount to dowload the soft and do adaptacion whith vcm2 ? if i buy used module for replacent do i have to do only adpatacion?
@MMDPERFORMANCE3 жыл бұрын
@Fordtechmakuloco is it possible for low voltage to the tcm to cause internal transmission damage? Dealer claims tcm is good, but low voltage caused damage and the transmission needs an "overhaul" for $4k+. After watching your videos I suspect the tcm is bad (or bad clutch stuff??). The trans makes lots of clicking sounds, says it's not in park when shifted. It doesn't engage reverse and wont shift to second (stuck in limp mode). Codes -2837 shift fork b position circuit range performance -287b shift fork cal not learned. -074a unable to engage 2nd gear The internals of the trans seem rather "simple" and I do not understand the claimed damage would happen. Thanks for any help, Mike
@mack1ford10 жыл бұрын
thats why i own old ford trucks less to go wrong. cars now a days is getting to complex and nothing is done by physical connection like a cable or rod.good video
@ktom45366 жыл бұрын
mack1ford unfortunately government like in uk pass laws so you get rid of old cars or tax them high do you are forced to buy new or newer thus keeping car companies in big business ....Too big to fail rather then focusing on being green same with everything these days even phones lol
@dustinkeim1795 жыл бұрын
2012 focus 120k driving down the highway and it kicks into neutral and wont go into gear until you coast to a stop shut the car down cycle the key start car again then take off and it will repeat in about 15 miles,?? any ideas
@deliawood1 Жыл бұрын
I’m in Australia and I purchased one in 2011. My granddaughter has had it for 3 years and the car just stopped in the middle lane of the freeway. There was no forward forward movement but it still works in reverse. Dealer states the module is faulty and cost of replacement is $A 1500.
@LevonPatemyan5 жыл бұрын
So when drive in highway like 50-70mph the REV is going up and I can't build up speed after pressing gas pedal couple of times it looks finding right gear then become normal
@LevonPatemyan5 жыл бұрын
Hi mate thanks for your video about ford powershift transmission i got problem with mine and spend lots of money to fix but nothing fixed i will try to make small video and upload to you see the problem i want to save my car life the ford wont help about the just told we can make service like oil and filter change but i already done and nothing help
@tenzATL8 жыл бұрын
FOCUS 2012, if you haven't experienced TCM issues symptoms doesn't mean you're in the clear. I found out the hard way, being stranded at an airport garage and waited 6 HRS for a tow. Make an appointment at your nearest dealer ASAP and fix it. Traction control lit up, radio shut off, car wont start, transmission indicator on dash gets wacky. Come to find out the dealership is backed up, TCM parts on back order and will take a minimum of a 2 week to get it replaced if i'm lucky coz they have a ton of other cars with the same issue. Drove a Toyota for 10 years till i wrecked it, figured i'd try a Ford, well guess its back to either a Toyota or Honda.
@brianw3903 Жыл бұрын
I have a 2012 ford focus se with a P0606 and P0884, I cannot shift past 2nd gear. I'm suspecting the PCM/ECM is defective. I also get an random hill assist that pops up. Any help would be tremendous help. Thank you in advance
@enriquemurillo67976 жыл бұрын
I have problems with the TCM Before and the ford dealer replaced the part and reprogram.. But now I have new problems , no reverse, 2 and 4 gears .. I find out is the clutch actuator B .. I want to replace it my self but I don't know if it needs to be reprogram .... 2014 focus ...by the way thanks for your teaching videos...
@thetruthonlydementia73797 жыл бұрын
2013 focus clutch actuator has failed twice for me (less than 40k) P0902. the subject of class action, Ford essentially has admitted the car blows chunks. Although I have a 7 year warrantly with a deductible, they fix for free for me anyway. I can no longer trust this car to drive anywhere
@zakbmh4322 жыл бұрын
Hey there, thank you for the video. What about a Focus mk3 transmission which engages only impair gears 1-3-5 but no 2-4-6-R, the diagnostic revealed there's a problem with the clutch actuator B (Low circuit...) I tried to invert the actuators but same problem, which means that the actuator B is not the issue origin. I also did some small vibrations on the clutch position sensor's connector, it resolved the problem the gears pass smoothly but few minutes driving in high traffic the issue comes again.. 😓😓 so what do you think about this issue? Thank you in advance Man.
@forrestbenson45177 жыл бұрын
Got a whole host of issues with my 2011 Fiesta. Slipping in 3&5, Rough shifts, missed gears, occasionally shuts out 1, 3 & 5. Comes out of lockup half the time when gas is released. No consistent DTC codes being thrown, but the Transmission Malfuntion "Service transmission now" comes on, only to go away once the car is shut off. Last time it threw a code was for friction surface issue. Have tried TCM flash at dealer, the ground wire TSB, had the seepage of fluid from bell housing, so flushed clutch plates and bell housing with acetone per another TSB (What a nightmare doing that in the driveway was). Have also used the clutch scrubbing technique with no success. Can't find a replacement clutch for less than $2,500 as it's Ford availability only. Any other ideas I should try?
@Buggen-Out-Yo3 жыл бұрын
I have a 2013 focus se 2.0l won’t start after i drive it. I checked battery was good, put new starter, new relays on starter and Ignition relay and new negative battery cable. I also used the other key. Also it seems when it warms up and gets driven it don’t start. But when it cools it seems to start again. I’m stumped! Any pointers?? Thanks in advance Great video!!!
@StormLaker3 жыл бұрын
Mine just failed out of the blue the other day. It's done the "shudder" since I bought it three years ago. Thankfully my car has under 100K miles, and is still covered under the extended warranty that Ford put out on these cars. Great little hatchback, I've gone on numerous trips of over 1000 miles round trip in it... The downside is that the part is on backorder, and I was told minimum of 15 days. Hoping the warranty provides for a rental car while this is getting resolved. I am going on a trip in a few weeks, and I need my car:-(
@RKCorinth3 жыл бұрын
Mine went out JUST under the warranty. They extended warranty from 100k to 150k if I remember correctly. They told me it was the tcm and that there would be no charge. Ended up being the TCM and the clutch. Cost me $1600. That lasted for probably 30k miles when the TCM went out again after my alternator went out and fried almost everything electronic in the car. I went to the local pick-a-part and pulled one out of another focus after Ford wanted $1200 for parts and labor for the TCM. I slapped it in the car in my garage, and it was great until it again went out. It was probably an original TCM that I pulled out though. Lasted another 10k miles until it went out again. I’ve gone around a few junkyards to look forward another TCM and have yet to find another one. It really is very simple of a job. Couple things to move out of the way, a few bolts to take out that hold the module in place, a wire harness to unplug from the module ,and it literally pulls right out, and the new one goes right in. The module needs to go through the “learning” process afterwards.
@Dorightby Жыл бұрын
How do you go about doing the learning process?
@votejustinout7221 Жыл бұрын
I have a 2013 Focus and it will shift into any gear but the car doesn't move in reverse. Drive is ok. Is it the TCM or is it the reverse actuator? Thank you for any advice you can offer.
@michaelhodge92899 жыл бұрын
Do a teardown video of the Ford dual clutch tcm
@oscarescareno5405 жыл бұрын
yes i would like to see that as well and the cost for parts are substantially lower than dealer costs
@nowzthetime2 жыл бұрын
What experience do you have with the shift control actuators
@brewcracker2 жыл бұрын
Hi, I have replaced my TCM for my Ford Focus 2013 1.6L and now it won't start. can you kindly help me on this. what do I need to do?
@giovannivasquez72235 жыл бұрын
I need help I have a 2014 focus titanium I had a check engine light code p0902 I already change the clutch actuators but now after driving it said warning transmission getting hot an the same code came back p0902 for clutch actuators do I need to change the tcm too
@jonidimeri15784 жыл бұрын
I have the same problem p0902 and p285e clutch fork shift. How you fix that and how much cost you. My focus 2014 have 95k miles.
@rogeliobartolome12324 жыл бұрын
Sir ihave a ford fiesta 2012 p07a7 code, already to replce surplus tcm the problem all gone tnx,,
@larsnesho253 жыл бұрын
How I know what number my TCM number if I want to replacement?
@alexnav80925 жыл бұрын
How can I program it
@fragonarag9 жыл бұрын
TCM was replaced on my 2014 focus at 1300 miles. Rough shifts and on a warm day in summer, car would not go into reverse. Seems to be fine now, just some clutch chatter on cold days.
@oscarescareno5405 жыл бұрын
i have the same problem with my 2012, but it wasn't identified until the extended warranty expired.
@adwokatdiabla77532 жыл бұрын
just wondering how can I tell/check what revision I have? or when I will try to purchase one online how can I tell what revision that TCM is?
@bryanb76395 жыл бұрын
Can these manual transmissions in the focus with autoshift be converted to a stick shift?
@joshuacollier58 жыл бұрын
Hey Fordtechmakuloco... your videos are awesome! I am thinking of buying a 2013 ford fusion 2.o l4 ecoboost 42k miles! I am scared of the transmition. Is this something to worry about on this car? Good buy or should I look for something else? Your opinion will be GREATLY appreciated . Thank you josh
@jenlovsey1298 Жыл бұрын
Do NOT buy! These cars are garbage!
@jorgemorado16302 жыл бұрын
Hi there, I got a P07A3 Code 2017 Ford Focus it does the loud clicking and what not when I try to turn it on I can only turn it on when the noises stop, is this related to the TCM?
@adwokatdiabla77532 жыл бұрын
and my 2nd question is if I will get a brand new TCM from EBAY does that TCM needs to be reprogrammed?
@davefrance37217 жыл бұрын
When Ford introduced the gearbox, they said it was maintenance free for 100,000 miles. NOW they say you have to change the transmission oil and filter every 30,000 miles, using specialist equipment at a cost of 150 UK pounds. clearly this gearbox was never tested in the real world, but on some bench somewhere. we have been lucky with our Gearbox so far, the only issue we had was a transmission failure on the dashboard one freezing cold morning. after switching off and back on again it was OK. a new battery fixed that problem in the end.
@johnwilson22507 жыл бұрын
They tested it in the real world... on OUR cars. Not sure who is worse, Ford manufacturing or the Ford dealers.
@49erscast Жыл бұрын
Hey bud..so I had to get a reman TCM for my 2017 Ford Focus from china..no way in getting one in the states right now. The dealership said I needed a new TCM so bought one that says it was already programmed 2.0L focus..I installed it today and it drives like the old TCM was in there..rough shifting…is it plug in play or anything else I need to do? From what was told to me from the dealership I just replace and drive and it will calibrate…the check engine light came on but not sure what the code is for now.
@molivera267 жыл бұрын
I have a question about this issue does the Ford Escape 2013 SE /1.6 4x4 ecoboost has the same problem?
@s996147 жыл бұрын
No. Completely different transmission.
@roninweiss88078 жыл бұрын
my replacement died within two weeks now on manual control
@chocolatemilk20763 жыл бұрын
I'm confused on the Auto Manual please explain how it is able to do so and can a car be converted is it the same transmission just different control computer
@korruptedkhaos81498 жыл бұрын
I have a 2012 focus and had the Trans control module replaced and now I get really loud grinding noise in second gear. it comes and goes and it's fine in third. what is wrong with it ? any ideas ?
@brendadouglas52695 жыл бұрын
It's a Ford
@roynamz9879 Жыл бұрын
Can you share what is the TCM part number for Ford Fiesta Auto 2012?
@moparmania867 жыл бұрын
My mom has a 2014 focus with around 30 thousand miles. She has only owned it for a few months. It has always had a shudder and slip in first gear. Trying to get going from a stop is a pain. If you go really slow and easy it will be OK most of the time, but if you try to drive normal, or have a lead foot its bad. I was looking to see if it had any codes with my snap on ethos. There were no codes? I then saw then was a relearn process for the clutch. I went through with the commands and then went for a drive. The issue became worse and now there was also a gear noise in 3rd. And the shifts happen quicker. I broke it back and did a relearn on the drums. This made some of the gear noise in 3rd go away but not all. It also has two codes present now. Which I neglected to remember. Though one was for something about too high of speed. The other was a U code. The engine light is not on. Any suggestions??
@tempro58952 жыл бұрын
I also have a 2014 focus, I'm going to have it taken to Ford in the next couple of days to fix a bunch of random idling problems and slipping going from first to second, and after I get this car fixed I'm going to immediately sell it. Shame shame shame on Ford for selling this piece of s***
@lindagall618 жыл бұрын
i had the same problem and they checked my car out and told me its not the tcm so today i was driving home and my park and drive light in the cluseter wqas flaishing fasat and at a stop light it would not move and i dont know what to do i alrady took it to the ford dealer and they coud not find the problem with it one week ago and they charged me a diagnositic fee of 149 now if i brirng it it agan they are going to charge that agaon its not far i dont know waht to do
@avurruva58367 жыл бұрын
My 2012 Ford Focus won't turn on ,out of nowhere turns on like nothing . What can it be?
@roynamz9879 Жыл бұрын
What is the part number of the TCM for Ford Fiesta 2012?
@mpenduloncube7604 жыл бұрын
I'm struggling with my Ford Fiesta 2011 l reolaced the selector module and dry clutches still give me transimiton problm
@shifty27554 жыл бұрын
The wires break in the gearbox loom in the engine bay. TRY THERE FIRST
@mrhanson99224 жыл бұрын
I want to know how to fix it..mechanically it looks fine. Computer board S1JWA..fomoco? It was going to be trashed by our mechanic. I tore it down..and suspect as above.
@LuhNoSho Жыл бұрын
I have a big question if u can answer it’ll help I’m asking u cause your a ford repair dealer guy , I got P0700 and P07A2 I changed the clutch actuators and it doesn’t drive or move in drive it has reverse but it won’t go forward it’s like it’s in neutral and rolling backward in my driveway
@mimomimozzza95463 жыл бұрын
Hello is same gearbox car renault volvo and ford ?
@smtshrek367410 жыл бұрын
It's also an issue on the focus.id add to the concerns engine over rev and over rev dtc,and no crank no start after shut off because PCM is not seeing park/neutral input from Tcm.
@FordTechMakuloco10 жыл бұрын
Yep Focus too but more common on early Fiesta.
@geraldmartinez4398 жыл бұрын
I own Ford focus Diesel Matic 2009 with defective Automatic transmission, it just would not shift. My mechanic say he needs to replace torque converter. Where can I get a used Matic for diesel 2009?
@fiestameisterse58684 жыл бұрын
Sounds like it's not defective just your torque converter went bad just replace it lol
@nathanspooner4992 жыл бұрын
Ok just got a 2012 focus for my daughter. It has a slow 1st to 2nd shift then will throw code and reverse will go away. Did grounds test ran and shifted great for about an hour of in town driving then started doing the same thing.
@timidater48037 жыл бұрын
what about the 2015 focus?? My daughter just rented on and thought the trans was going out!!! Rental agency said oh thats normal!!! No its not, what the hell?????Cant believe its still going on!!!!
@mariajackson11059 жыл бұрын
excellent thanks for sharing
@Orngecayman8 жыл бұрын
I have a ford focus and it doesn't reverse at all bu will go forward, could this be the TCM?
@jeffersongo4496 жыл бұрын
Nikodim Gorbenko same here. Jist turn the car off and it will be good once turned on again
@anthonyverona67002 жыл бұрын
Hi sir my car is Ford Focus 2012 model what is the main problem my car the RPM is not proper work like my gear also same time is not working?
@TheMaddy2108 жыл бұрын
i have a 13 focus n im gettin tcm intermittent with a code p0883 and p0884. when i try and start, i get a clicking sound. It takes about 5 to times to start. Also my odometer reset. Any thoughts?
@Anarchaotically8 жыл бұрын
Your battery is bad, or your alternator.
@patrickneil6617 жыл бұрын
Have you heard of any instances of a faulty TCM causing the transmission to stay stuck in 1st gear? It's a 2012 focus if that makes a difference or even damaging anything internal to the transmission?
@MisaBarba2 жыл бұрын
Did you ever get an answer to this? This is exactly what's happening to mine.
@christopherjacob98522 жыл бұрын
Same for me as well on my fiesta
@wilson24554 жыл бұрын
I bought a 2012 Ford Focus (LW series) brand new. The transmission/TCM has been replaced twice (under warranty). The current transmission / TCM is only 4 years old. All seems fine (aside from the occasional 'shudder' when coming to a stop).
@larrythompson27994 жыл бұрын
It's on its way to failure
@xDJeydenxD8 жыл бұрын
So after the TCM problem, the Ford Focus transmission, engagement, gearing and the other issues mentioned on the recall should be gone? Or is this a persistent issue that happens from time to time or milleage related issues?
@MikeCampSucksFatDick8 жыл бұрын
+Alan Suazo persistent, it does not fix
@blasmirdiaz58247 жыл бұрын
Ford focus 2012 reempalce the tcm is now presenting problem at the time of powering I must wait around 30 seconds to start the vehicle is tcm problem again or should perform some calibration
@autodiagnosticogonzalez61925 жыл бұрын
I have the same problem, how to resolve you?
@dealerauctionnightmare46894 ай бұрын
I have codes p087a, p087b, p090a & p06b in a 2018 Focue with 99k, wonder if it would be covered under warranty?
@K_3D_Official_12 жыл бұрын
Will the car die sometimes when you turn it clicks all crazy
@jacobkline5628 Жыл бұрын
i have the same thing with my 2014 fiesta, i’m not good with cars but i’m learning a little more but haven’t seen this video all the way, i hope it works
@jacobkline5628 Жыл бұрын
forgot to mention, when i come to a stop or even driving it loses power where im trying to engage but im just revving the engine instead
@ElLucho19702 жыл бұрын
My warranty expired 2 months ago and it just started acting up! And they are months behind on back orders
@kthospol10 жыл бұрын
We've also found this issue a lot in Thailand.Unluckily for me and many people found this after out of warranted(3 yrs).the cost for replacement is about 730 USD and "we need to pay ourselves" No responsible from FORD.We think that It's too fast for us. compare to other brand.
@AlyZ7177 жыл бұрын
What does it take for Ford to fix them? Do I have to wait until my car is dead? Taking to Ford but concern is if it doesn't throw codes again (local mechanic ran diagnostic and said was clearly TCM), they'll refuse to replace, even though they know these are an issue. It's like Russian Roulette with this stuff and I don't want to be stuck in the middle of nowhere!
@misssaydee14962 жыл бұрын
This is where I am right now:(
@TRY81GETYOU6 жыл бұрын
Plz someone can talk me what those code are P0707 - P2802-P286F help plz for 2012 Ford Focus se
@rickkb2lgm7 жыл бұрын
how long would it take the dealership to change the TCM
@majikninja52743 жыл бұрын
I've been waiting over a month on mine
@ggo3793 жыл бұрын
Hello. I bought a new TCM module and I want to program and adapt it. But I can't find the firmware. Where can I find the firmware for my car? Ford Fiesta ses 2012 1.6L
@choyrl3 жыл бұрын
Hi GGO. I have a 2012 Focus and my transmission failed last week with me not able to start my car from Park or from Neutral. It flashed a message "Parking Aid Failure" which is caused by a bad TCM. There is an extended warranty on Focus and Fiesta for 10 years or up to 150000 miles on the TCM under the Ford Customer Satisfaction Program 14M02. You can find that online or go to Ford owner website (under Recall) to see if that service program is available on your Fiesta. My Focus was fixed today with new TCM and recoding for the adaptive drive, all free of charge covered by 14M02. So you may want to inquire from your local dealer about 14M02 and if your Fiesta is covered. As stated earlier, you can also double check on the ford owner website with your VIN.
@ivanjimenez27254 ай бұрын
i have a question about the tcm on my focus. i have 2012 focus se with TCM problems. right now i just pick up a oem TCM from ford and my question is, can the new TCM could be program even when the old one wont work and it wont communicate with scan tool? i know your video is 9years old but this is a problem across focus and fiestas.
@AnonYmous-wu1fh2 жыл бұрын
Do I need to do anything else when replacing the TCM apart from the learning process again?
@FordTechMakuloco2 жыл бұрын
Programming too
@BobbyCulpepper.srv3fender9 жыл бұрын
Got one in today! wont start, died while driving, wont shit out of park, no communication with tcm. Gonna replace the module friday and reprogram it. Anything i need to know about doing the relearn?
@FordTechMakuloco9 жыл бұрын
srv3fender You must do the 3 relearns in the ids software after reflashing the tcm to the vehicle. TR, shift drum and clutch learn.
@bigcaptainschannel9 жыл бұрын
I sent you a message on your Facebook like page. Please read. Regarding 2011 Ford Fiesta not starting. I would like to hear from you. Thank you.
@antoniourbano61035 жыл бұрын
Bigcaptain's Chess what was the fix?
@alanhutchinson90277 жыл бұрын
I have got the shuddering problem with our 2014 Ford Focus, but after experiencing the B.S from the Ford dealership in Victoria B.C "we will never be going back to them, they suck.
@graemesydney386 жыл бұрын
You'll find it is the corporate mindset as much as the local dealer.
@EddieLeal4 жыл бұрын
@@MrBigsteve518 lol
@jr68357 жыл бұрын
I have a Ford Fiesta for 2015 and it has a bad transmission message but the speeds works
@keno775 жыл бұрын
I was a long time looking for a ford focus 2013-14 because I think the car looks great,but after getting to know all the trouble they have with the automatic transmission I think I have to drop this car for something else, I wonder if it is even worth to consider as an option, what do you all think, I'm afraid I'm going to regret buying a focus.
@clark2hl4 жыл бұрын
סבתא רבא don’t do it muy 2014 after 65000 star the problems
@maxthreshold3 жыл бұрын
I have already removed the painted area for better ground connection after watching your previous video, but the TCM still died on me (no start condition, stuck in park etc). I was wondering, could jump starting the battery potentially damage the TCM? I have read from different forums that their TCM died after a jump start. I remember doing the same before the TCM died.
@smithguy91092 жыл бұрын
After seeing your comment it’s got me scratching my head lol. I cleaned my grounds because I kept getting hill start assist unavailable, then transmission hot wait 5 mins, then traction control randomly turned off by itself, oh and also would have to turn the key a lot of times before it would start. While cleaning my grounds it sparked a whole lot while reconnecting. Now it shifts terrible and says clutch A is stuck. I wonder if all that sparking fried or shorted out my tcm. These focuses are a headache. Had mine since new and now have 167,000 on it. Trans repaired twice already can’t get a break with these cars.
@maxthreshold2 жыл бұрын
@@smithguy9109 have you already replaced your tcm?
@narinpong21152 жыл бұрын
No
@maxthreshold Жыл бұрын
@maksim bond yes, at first I was able to start the car from the fuse box. In the end, it turns out it was a faulty TCM which prevented the car from starting.
@maxthreshold Жыл бұрын
@maksim bond yes, after TCM replaced, car started again.
@garrettm79938 жыл бұрын
My 2015 Ford Focus has had issues since the first day I bought it. Everything from violent lurching, going into neutral sometimes while accelerating, and yesterday when my car was going into second gear it violently grind and jerked into the gear and a transmission fault service immediately popped up. I called Ford roadside assistance and it would've taken two hours so I limped it to the dealer. When the dealer turned it on, the light went off and drove normal. I've had this car for 5k miles now and I bought it brand new. It's been at the dealer every month since I've owned it in September 2015. It's stayed overnight once already and it's at the dealer again and I won't know what's wrong with it until two days from now. I love the car, I hate, HATE the transmission. I will try to convince the dealer to give me a manual Focus and they take this clunker back that I paid almost 30k for.
@MikeCampSucksFatDick8 жыл бұрын
+Garrett McKie I have the same feelings, love the car but wish I got the manual transmission. I would just get a lemon law lawyer if they say no, you will win with lemon law and get all your monies back.
@38911bytefree7 жыл бұрын
I have seen other vid where the erros clear magically. My bet is this was done on purpose in the transmision software to fool the owner when they try to complain in the dealership. "No errors, nothing to fix. Thanks you!!!!".
@ESPECTRO446 жыл бұрын
Garrett McKie Code P07A3??
@syedtauseefabbas4336 жыл бұрын
Thanks a lot for the information you provide us. It is really a great job to share special knowledge. Your experience and knowledge are very special that we cannot find anywhere else. Is there any chance to guide me what to do with Ford Galaxy 6dct450 if I cannot delete fault code P0949? It will be a great help. Thanks.
@javid66802 жыл бұрын
Sometimes I start the car everything works great,then when I turn off and on again ,reverse is not working and shifting is so bad and engine light comes on. When I disconnect battery for long time it works but will happen again
@maheshnaik19305 жыл бұрын
My ford focus TCM broke down. There is no availability in show room (Saudi) and show room service personnel informed that this part is not available and it will take one month to import from US. Also informed that I have to drive slowly in the city. Is that recommended to drive ? Please anybody let me know
@Lestergreen774 жыл бұрын
Mahesh Naik u gotta drive very slow
@thestackzco.91908 жыл бұрын
Brian, Thank you for all of the videos, they are helping me out! Question though, I have heard you talk about symptoms so If I could I would like to ask you a question. My 2012 For Focus has been to the dealer twice. The first time I was in for the trans service and I was told that my shutter issue it was the TCM and that is was warranted for up to 150K, mine has 120K but that I needed to make an appointment for a later date. I made the appointment and that day I was told that I needed a trans rebuild which would cost me $3K. The morning on the way to the dealer the car shifted great but one time before the appointment and now twice after the appointment I have had to rescue my daughter from being stranded on the side of the road or parking lots. The car, while driving or at a stop will randomly rev to 5 and 6 thousand RPM, up and down like it has a mind of its own. I go to pick up the car and I am able to get it home so sometime the issue goes away after the car is turned off and back on after a while. Is this a TCM issue? Please help. lol
@thestackzco.91908 жыл бұрын
+The Stackz Co. No check engine lights by the way.
@dominozonda2 жыл бұрын
Did you manage to solve this problem? And what was the cause?
@alteregos89493 жыл бұрын
In the 2012 they extended the warranty on the TCM to 10/150 as I am having it replaced this week and it’s covered thankfully.
@FordTechMakuloco3 жыл бұрын
Wow they actually had parts for the repair?
@alteregos89493 жыл бұрын
@@FordTechMakuloco here in Florida yes. Last week another dealer I originally spoke to gave me bad info saying the warranty was out. Luckily I called the dealer where I had the last recall work completed pleasantly surprised me with news that the warranty is 10/150k and the TCM is covered still and that they had the part. That was a major factor for me as to if I planned on keeping the car or trading or sell it. It’s a clean car and it was maintained very well. Runs like a champ minus the transmission issue and the failed recall repair on the passenger door. Nothing like the passenger door flying open on a right hand turn when driving lemme tell ya 🤣
@christianc13132 жыл бұрын
Just got mine back. Wont do the warranty repair until I replace the clutch at my cost of $1800
@alteregos89492 жыл бұрын
@@christianc1313 both cutches actually. There are 2 which makes it that much more annoying and expensive. Very smart to wait seeing they will have to break the trans down completely anyway. It’s not a tough repair and the tools along with the computer/software to synchronize it and align the actuators is the stick point where you need a shop to complete the work.
@dkironworks40372 жыл бұрын
I have a 2016 focus, battery died, after getting jumped and a new battery the car will not shift or go into reverse, parking brake works, will go into drive. No problems before the battery issue.
@charliechoi42137 жыл бұрын
hello Brian I have 2012 ford Fiasta clutch issue code.P07A3 replace new clutch but same probem same code show P07A3 Please answer
@mtsanchez2719 күн бұрын
What was the problem?
@kelnran10 жыл бұрын
I had my TCM replaced on my 2012 Focus about 2 weeks ago (around $1200). Is the NEW one an upgraded model or the same as the original pos? Also, it was on backorder for 3 weeks, assuming they are replacing quite a bit of these things. Any chance of recall? Thanks, good video.
@FordTechMakuloco10 жыл бұрын
Yours was out of warranty? These are covered by emissions warranty which is very long. Yes they have changed part numbers about 7 times now and the latest one you got should be ok now.
@wilson24554 жыл бұрын
if they made you pay, that's disgusting conduct as it's clearly a warranty issue, I bought a 2012 Ford Focus (LW series) brand new. The transmission/TCM has been replaced twice (under warranty). The current transmission / TCM is only 4 years old. All seems fine (aside from the occasional 'shudder' when coming to a stop).
@johnnydeep10515 жыл бұрын
@FordTechMakuloco can i know how many bolts that TCM have? Many thanks,
@mpenduloncube7604 жыл бұрын
How many bolts
@Uns463 жыл бұрын
4
@JL-cu8hd5 жыл бұрын
Thanks for the video. I have a 2014 focus that after 45 minutes or so of running and idiling throws a p287a and then loses reverse and 2nd 4th and 6th gears. If you shut it off and restart it's fine for a while till it's good and hot then you have to wait 20 minutes for it to cool down for it to work properly. Dealer said it's a clutch I have already swaped a and b shift motors and get the same result. I think the TCM has failed. What are my odds of warranty with only this code and symptoms. Thanks again.
@chippedspline4 жыл бұрын
Check on Ford website under Recalls type in your vin# it will tell you what Recalls are available
@wtewyweyewywey1579 жыл бұрын
There are a lot of Ford fiesta in Thailand got the same problem. Ford extended warranty for TCM to 5 year. But the problem still won't solve. So pity Ford customer
@sandracrawn6236 ай бұрын
Will the module keep the car from cranking?
@e43005 жыл бұрын
Just had my 2014 Focus TCM replace under warranty. Shifts pretty decent now but the Overdrive won't disengage when I push the button on the shifter but the Hillstart does work. So in other words when I engaged the Hillstart/Overdrive button the Hillstart will work but the Overdrive won't. Any Ideas?