Ford Focus TCM Repair DPS6 / Getrag 6DCT250 TCM repair ( Fiesta Focus etc)

Рет қаралды 24,488

Жыл бұрын

My attempt to fix the TCM for a ford DPS6 dry DCT transmission. The transmission was losing gears. Turned out the circuitry was water damaged.

Пікірлер: 30

@priyoidn2759 5 ай бұрын

Thank you Mr. Jugaar for your sharing

@kylemcpherson3986 Ай бұрын

Hi! It looks like youre from Aus. I watched your other video with the circuit board identification. Would you know what MOSFET would be responsible for the Input speed sensor 1 and input speed sensor 2? Both of mine are displaying faults on the Autel.

@TimelessMotors 28 күн бұрын

Did this work?

@gustatav Жыл бұрын

hi,..my dps6 is bunrnin the hall sensors, iss1, issb and oss. not at the same time...2 or 3 days between the failures. I check cables, conectors, after change 3 times the sensor, i change the tcm, resolve for 1 month, and the problen return, now the sensors buning with 1 ou 2 week diffrences time. Detail, the abs light is on, turned on when the problens start. the abs code is u3000:49. sometime the ligth turne off and at the same time the tcm ligh turns on. I didin´t find any wire in commun with abs and tcm, I thing just the can communication, but not directily. The wheels sppedy is ok and in the same values(check by scanner in the road)...any tip?

@RZJugaar Жыл бұрын

I can't find any find any connection between TCM and ABS . Agreed but U3000:49 points to power steering motor failure. No issues with your power steering? I would suggest start looking into potential wiring issues. maybe plug in an Oscilloscope and drive around. look for potential spikes in voltages.

@gustatav Жыл бұрын

@@RZJugaar no problen with power steering..just ABS

@omarlanderos3183 8 ай бұрын

The u codes Is for problems on tcm or pcm , its necesary replace the bad part to correct function

@marissaclarkson3128 Жыл бұрын

Would you repair any TCM for a specific price? How did u clean the inside?

@RZJugaar Жыл бұрын

Are you sure you have problem with TCM as there can be other problems too?? But regardless I won't do it as I can't guarantee a fix... Can be swing and a miss

@rodelcar.cambio Жыл бұрын

FRIEND, DO YOU CHANGE ANY COMPONENT ON THE BOARD OR JUST RESOLVE

@RZJugaar Жыл бұрын

It's mostly soldering issues but Wait for my new video where I'll discuss various board components and what type of errors they can cause.

@rodelcar.cambio Жыл бұрын

@@RZJugaar THERE'S A PREDICTION OF THIS VIDEO BECAUSE I'VE BEEN STUDYING FOR 2 MONTHS AND I HAVEN'T GOT ANYTHING YET

@rodelcar.cambio Жыл бұрын

@@RZJugaar CAN YOU GIVE ME YOUR CONTACT

@DesiAnanth Жыл бұрын

hi sir i got a code in my car tcm error. i just did the ground mod and grounding kit install due to bad factory grounding on this model and code is clear for now. But im still afraid that tcm may be getting spoiled soon i dont know. if i put a junkyard tcm does it need reprogramming? will the ford dealer do it?

@RZJugaar Жыл бұрын

What code are you getting? What year is your focus? If you are using junkyard TCM then you don't need special reprogramming. It is adaptation rather than programming. just put in and start using it. It'll adopt to your transmission soon enough. Dealerships wont put used parts in. Before going down that path, make sure that your TCM is the culprit.

@DesiAnanth Жыл бұрын

@@RZJugaar i dont want them to install the tcm in the vehicle. i can do that myself i only want them to do programming if necessary

@rodelcar.cambio Жыл бұрын

Tem o manual de reparo desse modulo

@RZJugaar Жыл бұрын

I haven't seen a repair manual for it but i did see a couple of line diagrams that identify the pinouts. If you know what problem you are after, those pinouts can help you.

@rodelcar.cambio Жыл бұрын

@@RZJugaar se vc tiver as pinagem para me conseguir agradeço

@rodelcar.cambio Жыл бұрын

@@RZJugaar tem algum numero que posso te chamar

@RZJugaar Жыл бұрын

@@rodelcar.cambio If you have access to Alldata software, you'll get it. If you don't have Alldata, try searching on the internet. I saw it on a few places. Unfortunately i cant paste any links here

@pedroveloso9707 Жыл бұрын

7.00: that is a cool solder joint, cant do that is incorrect, in there you need a 80W~100W solder iron fine tip, and to preheat the pcb board before start soldering. hot air station is advice.

@RZJugaar Жыл бұрын

working on my soldering skills

@pedroveloso9707 Жыл бұрын

that board are a pain in the a**... there allmost nothing to repair there, high complex robot, very expensive to buy new, and the worst, renault do not have in stock to sell. ( yes!!! its the same ).

@RZJugaar Жыл бұрын

I saw Dorman selling Fiesta and Focus TCMs with aftermarket internal solder joints, similar to what i'm doing here. If you can get it programmed for Renault, give it a try.

@marissaclarkson3128 Жыл бұрын

Where are you guys finding aftermarket ford focus TCM? I can only find ones from China but I’d rather stay local.

@RZJugaar Жыл бұрын

@@marissaclarkson3128 There are no aftermarket TCMs. Chinese ones are salvaged parts cleaned and painted. Dorman TCMs are salvaged, opened, cleaned and soldered and then resealed.

@omarlanderos3183 8 ай бұрын

In the Ford dealer Buy a tcm on $300 dollars with a core to change