FX Masterclass : Regulator Maintenance & Rebuild

Рет қаралды 82,713

5 жыл бұрын

FX Masterclass - World-renowned airgun smith, Ernest Rowe, shares a lifetime of airgun knowledge. covering everything from basic airgun maintenance to comprehensive step by step repair tutorials.
In this Episode, Ernest demonstrates how to clean, maintain and rebuild a standard FX regulator. These are the regulators found in the Wildcat, Royale 400&500, Boss, Verminator and Gladiator MkII.
To order parts or speak with a certified FX Technician call or email:
service@fxairguns.com
(866) 639-0772
If you have a specific tutorial you want Ernest to do, please leave them in the comment section below.

Пікірлер: 63

@kennethpettersson7807 5 жыл бұрын

Your FX Masterclass raises the value of FX ownership. Thank Ernest Rowe for informative videos.

@jercool 4 ай бұрын

Thank you it was worth a lot👍🏻👍🏻👍🏻

@customcutter100 2 жыл бұрын

I just bought a used FX Wildcat Mk I. I wouldn't have considered buying it without finding your video's. Thanks for sharing your knowledge. Subbed.

@ken244 3 жыл бұрын

Thanks for all you do Ernest

@cyocaller 5 жыл бұрын

I am glad FX is finally putting out repair video on there guns . It would be nice to have a breakdown on parts for each gun like the FX Bobcat mk2 , hard to find !

@Zeus-qo7zf 5 жыл бұрын

Good Ernest, thanks from Spain

@daveh9907 5 жыл бұрын

Thanks Ernest, Now I can picture when turning the regulator adjustment CCW I'm tightening the Nut!

@tomatepintor6203 2 жыл бұрын

NO pare de hacer videos, todo es genial, nos ayude mucho a los que tenemos la suerte de tener un Impact.

@dustyboyer5623 3 жыл бұрын

MR. ROWE i have the wildcat m3 & mavrick sniper both .25 cal You have perfectly covered all my ?s and then some. Thankyou thankyou.

@nisouck6514 4 жыл бұрын

Nice explainations; thanks a lot!

@abuagil1496 2 жыл бұрын

Great video, very informative.....GOOD LUCK...FROM INDONESIA

@edosancl 5 жыл бұрын

Finally! come on! more more! Thanks! Request: Mods for shooting slugs!

@gorankovacevicvazdusnepusk3447 5 жыл бұрын

Nice video.Great. I hope that Fx is going to make video of complete x barrel dissasembly soon.

@mytube3687 4 жыл бұрын

Thank you , by following the video I manage to repair a leak on my air tube and get 880pfs velocity with my fx wild cat 0.22 and 18.13 gr. Bro’s, you have leak it’s better replace all seals on regulator and others as well it will not cost you high for seals and it solve you almost all leaks.

@russelllong1543 4 жыл бұрын

Great video, very informative, any idea how you could release pressure from a locked up regulator installed in the tube.

@farooqjamatee 4 жыл бұрын

Great sir

@kenlumhemang7654 5 жыл бұрын

Good, keep it up

@ramvan2284 2 жыл бұрын

Thanx Earnest

@arvilmatlock7921 5 жыл бұрын

Happy holidays mr.rowe.just wondering if you could let us know where we can buy tee handle Allen's and Allen bits for cordless drill with links to purchase them as too the aerosal for checking for air leaks,and what you do for cleaning all the parts?

@N71403 Жыл бұрын

Hey Ermest great work as always! I just got a Bobcat to add to my inventory, barely used. I assume this video also covers the Bobcat? I cannot find much teardown info Please advise if you can your videos, including, I’m told, Royale as it is supposed to have the same action. Greatly appreciated!

@AffordableAirguns 5 жыл бұрын

Hello Ernest, my question is, what is the measurement between the lock nut and the aluminum body?

@user-hr8eb9rx6n Жыл бұрын

It is a pleasure to watch these videos with such valuable technical information. Thanks to this video I am about to fix my Ben Taylor and Son regulator installed in my FX Cyclone (it is bigger than the one shown in your video, which by the way I have it in my FX royale 400). But this mission is not possible without knowing the measurements of the internal O-rings of this regulator (I do know the measurements of the external ones). Without this information, it would be necessary to acquire a new complete tank without drilling, and add a regulator from another brand. Could you tell me your measurements? I would be very grateful. Kind regards.

@skeptic4reason 3 жыл бұрын

Is there a video like this for the regulator in the FX Streamline?

@moonc4lf 5 жыл бұрын

Yesterday i pushed 1000th pellet thru my Streamline..i hope i won't be needing this repair soon lol

@UTB365 5 жыл бұрын

Nice video. Ernest, Thank you for the clear explanation. My .22 wildcat has some issues. the velocity varies from 840 to 1230fps. It reaches max velocity from 4th shot onwards. Does it means that the regulator failed? Is it required rebuild from factory setting. Thanks in advance.

@ernestrowe927 5 жыл бұрын

Yes need to reseal the reg, most likely it’s the HP oring on the pistons, while you have the reg apart replace all oring -- even though the my look new.

@stedyone1090 5 жыл бұрын

Doesn't FX have a service branch in North or South Carolina? They owe me an updated larger regulator on my Impact

@brandonmatz9832 2 жыл бұрын

I set my regulator pressure @ 120 that's why my gun very seldom leaks if it does I just replace or readjust it maybe even drop it I used to run it at 140-150psi and it didn't like it was shooting erratic.

@ralstonraz 5 жыл бұрын

Nice video Ernest. A quick question. How do I get the regulator pressure to be higher. Let's say 145 bar. I see that I have tightened down the nut very hard already. Will turning the brass nut counter clockwise a bit for more piston travel help increase the regulator pressure too?

@ernestrowe927 5 жыл бұрын

You need to tighten CW the nut to increase reg pressure, while you have an Allen wrench on the piston to prevent piston from rotating. Attach a gauge on the action to confirm output of reg

@ralstonraz 5 жыл бұрын

@@ernestrowe927 sure. Will. Do. Will moving (screwing in and out) the brass knurled part which allows piston to move up and down help change the regulator pressure too? I am unsure about that.

@ramvan2284 5 жыл бұрын

Ernest, I have an fx Royal 400 (.22) and want to know if there is a regulator installed already. Is there a way to tell without taking the gun apart? I do see that there is a hole in the breech block just under the guns pressure gauge and the gun has the carbon fiber bottle... Does this mean the gun is regulated (because of the hole behind the regulator )? Thank you sir..

@jgrimsta 4 жыл бұрын

If you have a hole right behind the pressure gauge, you have a regulator. If you had a hole there, but no regulator, all the air would just leak out because that hole is right between the two o-rings on the regulator body.

@bodge6886 4 жыл бұрын

Are the measurements not different for variable foot pound setting.

@obiwankenobi3571 3 жыл бұрын

Do these increase ft/lbs power at the muzzle?.... I want to modify my sub 12ft/lb gun to achieve more I have an fac but don't want to spend the money on another gun

@mikemayne9370 5 жыл бұрын

Where to get cool black and silver vertical pull on cocking lever

@jeanfrancoespina9930 3 жыл бұрын

Whats the quickest and simplest way to increase power in my wildcat mkll señor? Gracias/ salamat

@weirhauch1002 5 жыл бұрын

Finally , I managed to see your face.

@Jeeper1378 5 ай бұрын

Maybe someone can help me here. The regulator on my Avenge x will only adjust down to 1900-2000 psi. Is there any way to modify to get it lower ?

@iloveairgun7908 5 жыл бұрын

Do you make video fx royale 400?

@kenlumhemang7654 3 жыл бұрын

Which rifle regulator is it ? Or all regulator are same in all air rifle ? Kindly be specific

@v.laldanmawiamawitea6419 5 ай бұрын

Each and every refill from scuba to my wildcat mk1 tank, it need to adjust again from scope. What the reasons plz

@FXAirguns 5 ай бұрын

What do you mean exactly, change the regulator setting ?

@v.laldanmawiamawitea6419 5 ай бұрын

@@FXAirguns Huma Regulator (in stead od Original) setting at 110 Bar for FX Wildcat mk1 and the speed is 850 fps (approx). Whenever adjusting from My Scope at target shooting, it always change the consistency after refilling from scuba. So, what can be the reasons?

@carsmax 3 жыл бұрын

Hi Ernest. I bought a reg from HUMA for my Bobcat MK II .22 cal but I don´t remember wich way to put in the new reg after several month of buzzy working. Pressure numbers on the reg facing the trigger side? Or facing air tube ? Can you help me out ????

@Erasmuspipebagger1 3 жыл бұрын

Numbers on tape are high pressure side, so that side to cylinder / high pressure air. The adjuster is inside the high-pressure which means obviously to adjust a huma regulator you have to take out of the cylinder.

@carsmax 3 жыл бұрын

@@Erasmuspipebagger1 Thank you so much !!!!!!

@shashisegar8140 3 жыл бұрын

If it is regulator issue tell me how to service it should I remove the regulator discs and cleans..please advice

@FXAirguns 3 жыл бұрын

If you would like help from a technician with FX USA, please feel free to e-mail us or call in, and we will have someone reach out to help guide you through any difficulties you are experiencing. Phone: +1 866 639 0772, Email: Serviceusa@fxairguns.com

@hmongwild 2 жыл бұрын

I have a leak issue. Replaced the two big and small orings on the regulator. But didn’t open up the one you showed here. Still have a leak seaping threw the little port between the barrel and the holding tank. Would doing what you showed on this video solve my leak issue

@zackoberle3731 4 ай бұрын

Same issue on mine. What did you figure out?

@hmongwild 4 ай бұрын

Changed out all the rings even the very small ones inside. Lube up the seals double checked everything carefully and it still has that slow leak. I just left it like that. Im out of ideas.

@shashisegar8140 3 жыл бұрын

Hi ernest.my kalibregun cricket. 25 has some issues in fps fluctuation from 850 to 1000 nd first shot will be 550 fps after second shot it jumps to 850 and keep on raising to 940 960 like that..please tell me what would be the problem

@FXAirguns 3 жыл бұрын

@gulfair-cavalry-tango1011 Жыл бұрын

FX should sell new replacement regulators already adjusted and set for plug in and play.

@TeireiPhaiKhawlum 5 жыл бұрын

Is it legal to carry these airguns on aeroplane? Do you have distributors in India? How can we buy FX air rifles in India?

@ahpv1010 5 жыл бұрын

Are you really interested to buy one?

@mikemayne9370 5 жыл бұрын

When can we get extra add on plenum for impact

@FXAirguns 5 жыл бұрын

Mike Mayne It’s still being perfected with other parts that need to be upgraded. Probably March

@FXAirguns 5 жыл бұрын

After IWA in March

@paulward3120 5 жыл бұрын

Where has all your Old vids gone !? I've lost them from my store of liked & watch later✋ has KZfaq been at it again? They also deleted my Sub to ur channel😱🙇 The main reference one was the gladiator MK 1 action split & Power control O rings!