As always great videos. I look forward to your posts, they're extremely informative and very well made, thank you so much.
@philipharrydeighton273210 жыл бұрын
Thanks for the video, you have shown me it is really very simple to change pressure if you are careful. This is similar to my engineering work. Thanks for taking the time to show us
@ziadaa10 жыл бұрын
Good job!
@krysks0410 жыл бұрын
Your videos are cool and I see you know a lot about airguns,regulators etc.. thumb up
@mughram10 жыл бұрын
thank you for share :) keep it up please
@jercool5 ай бұрын
Thank you 👍🏻👍🏻👍🏻👍🏻
@royale50039 жыл бұрын
Great informative video, do you have any other suggestions on improving FX royale models?
@CHOPERUS235 жыл бұрын
It seems the same kind of design as Theoben use. Remove regulator, install a fast flow valve and increase hammer spring tension! Find the sweet spot and you'll have a good 20 full power shots before the power starts to curve along with a massive increase in power.
@robertasliorancas74749 жыл бұрын
So what is regulator pressure setting for .25 cal Royale?
@garlorco8 жыл бұрын
Thanks for the video Ernest. Do you know of resources such as this for working on FX guns? I have both a Indy and Verminator Extreme and would like to do my own work when the warranty runs out.
@nikanim10 жыл бұрын
I own FX Gladiator MKII,6.35, 600mm barrel, regulated. I think the factory output pressure is set to 130-135 bars, not 160 as you've said. FX Boss is set to 160bar.
@lilvfr400boy7 жыл бұрын
hi there will the bobcat tube fit into the royal block adapter? my bobcats brass fill tube has failed at the welds which is common so id like to put the royal tube adapter on instead but remove the foster nipple in place of a microbore air hose to the rear filler and guage
@bigblue7588 жыл бұрын
Is it possible a review for the regulator and other parts on the fx wildcat 22 high power? Thanks a lot.
@NANDOTCBASS9 жыл бұрын
Is there a regulator for the royale 400 with the power adjustment or is the same for both models? Also where can i find one of those that eliminates most of the bell curve?? Thank you very much
@kaseyjohns51694 жыл бұрын
So if I turn hammer spring clock wise my fps will go up? I have the fx bobcat mk2 in 30 I would like it to shoot between 850 and 900. How many full turns should I turn it?
@MrTuskan9 жыл бұрын
Hello. how to unscrew the bronse regulating part? i need to take the whole regulator apart for replacing the o-rings inside - it leaking air throught the ventilation hole
@carsmax6 жыл бұрын
Hi. can I shoot my Bobcat mkII below the reg pressure? 145 bar. Or will it damage the system ?! Thanks!
@elekn7118 жыл бұрын
is this the same princaple on a fx varminator
@simonwilkes60544 жыл бұрын
All vidio footage on adding/ removing power from regulators on Fx Impact. Seem to already have a blank removed fron the screw. Mine has one and I am unsure if I am allowed to remove it to add preasure. Currently reading 25 on reg pressure. Any Ideas? Please
@antj2119 жыл бұрын
is there a way to take off the stock ldc?
@mnahi20098 жыл бұрын
help me please i have FX royale 500 6.35 its too slow and week even on the maximum power power adjuster is not a solution
@dannywarren52046 ай бұрын
Any chancenof doing a video like this for the boss owners... we have been left out when it comes to these types of videos... I'd like to know exactly what I'm doing to adjust and repair my regulator.. and gun
@maarodigro2266 Жыл бұрын
I have FX bobcat MK2 in.25 cal, can i remove sylender with out degas the airgun
@harryedwards93916 жыл бұрын
Hello friend How do you take the stock off of the my 2 Bobcat please ?
@antoniodicappo4037 жыл бұрын
Hi, can you tell me the exact dimensions of the FX Boss block? Length, height and width please. Thanks so much
@kaseyjohns51694 жыл бұрын
On my bobcat I thought my regular was in the tube? I want to turn it up some.
@hmelkan9 жыл бұрын
does this regulator work for FX Gladiator? thanks
@hsnmzpak67308 жыл бұрын
please show us how to adjust the fx regulator. I need to adjust my wildcat regulator
@mortus637 жыл бұрын
Hi nice video my fx royale 400 air loss from the little hole next to the manometer i ask arizona airguns and is said need to replace the dowty seal but i dont where is locate that part can u explaint please or some body thanks
@luftgewhrschutz70997 жыл бұрын
Hello, my Royale 400 only about 850 w/ 16 gr. pellets. disappointed. What you say to do is loosen the loctite & turn the screw clk wise to increase the fps , is this correct. thanks.
@cypriantem697 жыл бұрын
Yes, this will change the power of your gun, but do not expect extreme changes in fps rates. Perhaps you can increase the speed up to 20-30 fps, which I did, however, if you need more speed you need more air pressure for more speed and the hammer spring of FX is not strong enough to push the valve harder.
@62526506 жыл бұрын
This is only for fine tuning the velocity. If you want to increase the speed for 100m/sec or more ,you have to unscrew the locknut that holds the cup-washers tight, on the back of the regulator. Then fine tune with the hammerspring.
@fc11337 жыл бұрын
What a pain in the ass to do this. I guess things have changed a little bit since 2013... On the Impact you can do this without taking the gun apart. Right? Too bad I cannot do this "on the fly" with my 2016 Bobcak Mk2... Anyhow, thanks for posting.
@Cazanneke8 жыл бұрын
Does anyone knows the size of the o-rings??
@ghiapower39088 жыл бұрын
11,6x2,4mm
@tornhill7 жыл бұрын
Hi. Just got a FX Royale 500 and looking for instructions how to mount the high power kit I got. Anyone know a good tutorial?
@armaslover7 жыл бұрын
tornhill have you already installed it? i have a kit intstalled on my rifle as well. i bought my royale in Sweeden so it was 10j. Now is full power. if you need help i can help you
@armaslover7 жыл бұрын
If you need help let me know, i'm sure i can help you. I've installed it myself on my Royale 400
@tornhill7 жыл бұрын
Jag har inte installerat det ännu. Tänkte göra det under helgen. Alla tips är välkomna då jag inte hittat någon instruktion.
@armaslover7 жыл бұрын
lol i did not understood anything. i'm not Swedish. I just bought the rifle there but i can help you anyways
@armaslover7 жыл бұрын
done!
@N71403 Жыл бұрын
Useless. How do I adjust the regulator on my Bobcat. You only showed how to remove it. I need to bring it back to 130 bar as it is 120.