In this video, i go through how to sleeve the servo bores. A worn out bore will cause false pressure control solenoid codes
Пікірлер: 78
@TheWoodStroker Жыл бұрын
Your voice reminds me of another great teacher: New Yankees Norm Abrams. Thx
@alanchan1772 Жыл бұрын
Thank you great video.servo bushing repair.👍
@codiesmith34302 жыл бұрын
I have a 2005 ford ranger 4.0 with 4wd and the 5r55 transmission. I have recently been throwing a p0733 for incorrect 3rd gear ratio. When taking off with more than half throttle the rpms will rev 3000 or higher and the light will be thrown.I have a scan tool available and all the gears are present except for 2nd and I have heard the truck has two different shift patterns based on throttle position which I am not sure of but have noticed it to shift smoothly and normally as long as the rpms are maintained below 2000-2100rpm. I dropped my pan and installed a new epc solenoid and filter while also inspecting the fluid for signs of damage which everything looked absolutely fine no shavings and clean fluid. The truck has 58,000 miles on it and I have noticed it to of been somewhat strange while shifting before the code was thrown for a few months prior to it appearing. If you get this thank you so much for your time and knowledge.
@GaryFerraro2 жыл бұрын
if you drive it normally what happens? does it flare on 2-3 shift?
@codiesmith34302 жыл бұрын
@@GaryFerraro I believe so. As I take off down the road from a stop it seems to not want to go into second gear as the rpms will climb up into the 3000+ range
@nosoyono10815 жыл бұрын
Thanks for the info
@user-hi2fu2wh8k2 жыл бұрын
Hello Gary Ferraro. I'm from Kazakhstan. We do not have a 5R55S ServoBore repair service. Please tell me where I can buy such a repair kit. If this is not possible, please tell me the dimensions of the trimmers. B.Thank you very much
@chronobot20014 жыл бұрын
I would have like to see how you cleaned the shavings out after drilling.
@GaryFerraro4 жыл бұрын
I have a big wash tank, i ran it through the washer again
@jrm1632 жыл бұрын
Hi Gary, how much is this service please? I have to get prepared. Thanks!
@420Brew6 ай бұрын
What size were them bore bits?
@GaryVonPein-zw4ty7 ай бұрын
Will a worn servo bore cause slow engagement of overdrive ( shifts into over drive when warm but not cold)? Otherwise my transmission shifts fantastic in every other gear
@GaryFerraro7 ай бұрын
How is the 1-2 shift, the front band is 2nd and 5th. Do you have a scan tool that shows live data
@GaryVonPein-zw4ty7 ай бұрын
@@GaryFerraro 1-2 is mint , all the gears change great no slip or anything, and overdrive still works, it just decided it only wants to go into overdrive when warm, I had a stall converter originally and it felt really loose for ages and it threw the TCC code, so I changed out to a standard converter, and it feels nice and tight , my mechanic checked solinoids , fluid was great ect, everything checked out good, so I’m abit puzzled
@NOEISY17 жыл бұрын
Hi, a Question please I have a 1999 ford explorer 4.0 5R55E with a code PO715 I was told they need to open the transmission to replace the speed sensor.Is this statement correct? asking for $600.00 if nothing else its broken .
@GaryFerraro7 жыл бұрын
Yes, it is mounted inside, bolted to the center support
@TheJeepxj172 жыл бұрын
Hi Gary. My 5r55e shifts fine thru all gears but I lost overdrive. Once overdrive is needed around 50 mph and the transmission goes into limp mode flashing light. I'm getting a TCC code a VSS code and Trans range code. What ya think. Second gear is fine
@GaryFerraro2 жыл бұрын
Does it seem like it’s falling out of 5th
@TheJeepxj172 жыл бұрын
@@GaryFerraro it never goes into fifth. It just holds fourth gear steady and will run 3,000 RPMs at highway speed. Up until that point every gear shifts very smoothly but once it goes in the limp mode the high pressure makes every shift harsh
@mastagee85748 жыл бұрын
What do you think about those new servo replacements with the modified pin and plastic sleeves?
@GaryFerraro8 жыл бұрын
Who makes those, i actually dont know about this
@mastagee85748 жыл бұрын
Check out AJ1E
@davidmartin22316 жыл бұрын
MASTAGEE I ordered mine
@GaryFerraro5 жыл бұрын
@R Diaz Yes, i have seen those but never used them, you had good luck with them?
@h.d.52883 жыл бұрын
@@GaryFerraro The sleeves are made out of brass? I seen some made out of steel, do you think those would be more durable?
@craphittingthefan94455 жыл бұрын
Do they not make something a little more easy, Im am sure Sonnax must make a o-ring pin by now instead of all that hard work.
@GaryFerraro5 жыл бұрын
Sonnax sells the sleeves as well
@xtremegearheads8 жыл бұрын
hi Gary. great video. have you ever had a delay engagement into D and a 2/3 shift flare ? 5r55s after overhaul with new servo bore update . we tested vehicle and put it on the bench 2 times . codes po733 and po745 . any thoughts ? very much appreciated. Happy holidays
@GaryFerraro8 жыл бұрын
+xtremegearheads Hello, was the solenoid pack changed, that can cause these issues. Happy Holidays
@xtremegearheads8 жыл бұрын
+Gary Ferraro we replaced it with a new one from trans star.
@GaryFerraro8 жыл бұрын
+Gary Ferraro What was the original problem?
@xtremegearheads8 жыл бұрын
+xtremegearheads originally we had a burnd od band and destroyed the drum. we replaced the forward planet ,drum sun gear .thanks for replying I've been stumped this is our 6th 5r55s and first issue after a build with servo bushings update oh we also replaced the servo pins too.thanks again for replying special on Xmas . I just want someone to lead me into the next direction .
@GaryFerraro8 жыл бұрын
You replaced the o/d section? There are 2 different sun gears 24t and 38t, yo put the correct sun gear, that will cause the 2-3 flare. By chance have you put a preesure gauge on pc A tap, What sleeves do you use Northland?
@adamsorell48512 жыл бұрын
Can you do this without gutting trans?
@GaryFerraro2 жыл бұрын
No. has to come apart, some companies sell the servo pistons with a bushing on them, think it some type of nylon material but i do not use that product. If you use those servo pistons, you can do this with out gutting the trans, i only use the bushings
@gisterkiller7 жыл бұрын
why dont they make the sleeves out of steel
@GaryFerraro7 жыл бұрын
GisterkillerTech Not really sure, but after installed works better than new. Thanks for watching. Gary
@iam83576 жыл бұрын
Because they cant profit of a sturdy component
@Pendawa_Diesel_Plus4 жыл бұрын
my 5r55w trans problem no 3 gear i must repair the servo bore?
@GaryFerraro4 жыл бұрын
band could be broken, if so, i would say yes to the bores
@Pendawa_Diesel_Plus4 жыл бұрын
@@GaryFerraro the problem is in drive no 3 gear the gear shift lose 3 gear, 1 2 to 4 and 5
@Pendawa_Diesel_Plus4 жыл бұрын
@@GaryFerraro i have replace solenoid pack with a new but no fix the problem
@Pendawa_Diesel_Plus4 жыл бұрын
@@GaryFerraro but no dtc if scan with scan tool no dtc
@GaryFerraro4 жыл бұрын
@@Pendawa_Diesel_Plus solenoids will not fix the problem, your band is probably broken, anything in the pan when you had the pan down
@mastagee85748 жыл бұрын
look up AJ1E
@reble_uwu34054 жыл бұрын
thats a corvette servo? can i insntall that on it
@Mr.Caring2 жыл бұрын
Say what🤔 We're made in HIS image. HE made us with the power of free choice A good prayer: I'm a sinner JESUS please forgive me for all my sins I know you shed your Blood for me on the cross at Calvary. Thank you JESUS for my salvation and for shedding they Blood for me. I love you JESUS. Romans 10:5/10 ct...❤️k JESUSisLord!Amen... Amen.. If you'd like to call someone who cares 83 For Truth. bc you don't know when you'll die? .y r u hesitant. .. .... .. . .