How to Change a Hydro Drive and Blade Belt on a Wright 36i Stander

Рет қаралды 8,813

Күн бұрын

In this video, I will show you How to Change a Hydro Drive and Blade Belt on a Wright 36i Stander.
Gwinnett Lawns performs these services and others such as lawn care, crepe myrtle pruning, light landscaping, spring and fall cleanups, leaf
removal in Lawrenceville, Dacula, Grayson and surrounding areas. Take a look at my webpage gwinnettlawns.com/. Check out my new
Instagram page @gwinnettlawns
#wright36i
#changeabladebelt
#gwinnettlawnslawncare
Here are the items I used in this video.
Proslide XT▶ amzn.to/2LUEzCC
Equipment I am currently using:
-------------------------------------------------------------
Hour Meter▶ amzn.to/31k2RuG
Echo PAS 2620 ▶ amzn.to/2WCS4qS
Articulating Hedge Trimmer ▶ amzn.to/2TBd8fq
Echo SRM 225 String Trimmer▶ amzn.to/2MRmLV6
Honda HRX 217 Mower▶ amzn.to/2D4t3Mj
Echo PB 8010T Blower▶ amzn.to/2D32bfO
Edger Blades▶ amzn.to/2WaIX0f
Jungle Jims Mower Lift▶ amzn.to/2WjoZR0
DynaplugTire Plug Kit▶ amzn.to/31FDql2
Powertye Ratchet Tie Downs▶ amzn.to/2MpNcSL
Etrack section▶ amzn.to/2s6LhLH
Etrack mount plate▶ amzn.to/35RYjLC
Longacre Oil Filter Cutter▶ amzn.to/2R6Jct4
BigBoyJapaneese Saw▶ amzn.to/2Jzh9Sa
gwinnettlawns.com/

Пікірлер: 19

@officeanderson2661 3 ай бұрын

Thanks for the video!

@r.corcoran109 Жыл бұрын

Hey Russell it's Rick Virginia beach virginia. Great job there showing everybody how to change those belts because they are a bear. but a little secret on the lower pump Belt tensioner you could take the Mounting bolt where the tension bolts, loosen it and that gives you more room to slide that belt underneath just thought I'd share that with you, but other than that great job man.

@GwinnettLawns Жыл бұрын

Thats a good tip.

@jbird5211 Жыл бұрын

Man I searched high and low for a video on how to change the hydro belt on my Scag V-Ride 36". Although this is a different model. It is pretty much the same technique. Only difference is the Scag has a guard to hold the cluth in place which must be removed before slipping on and off the belt. Thank you man!

@rellmonger7935 3 жыл бұрын

Yeap I changed my Bobcat 36" WB 2020 left me stranded. Luckily the driveway was slanted down hill. I had about a 70ft push from the backyard to my van. Then that 560lbs WB I had push up the ramps. Awwww man the home owner helped for about 2ft. Then I grunted and got it up there. It was a lil stick caught up there. That was my 1st time bought a new belt since it's 2010 model & old in years but less then 170 hrs on it

@JustinJoyinglife 3 жыл бұрын

Is there a bolt head under the tensioner pulley you could use to crank it back for easier belt install? Just curious. Not bashing. I enjoy videos like these so thank you for the time with labor and content creating and sharing with us.

@GwinnettLawns 3 жыл бұрын

You could loosen the pulley a little but it would take more time than just doing it the way I do. You have to be careful NOT to loosen it too much or the spring will come off, then you are going to have a terrible day getting it back on.

@JustinJoyinglife 3 жыл бұрын

@@GwinnettLawns I wasn't meaning loosening the pulley, I meant using the bolt head as a pry point with a wrench from the bottom instead of using the edge of a socket and ratchet and then finagling the belt around it. That's how most automobile tensioners I've came across are set up and a few of the riding mowers.

@GwinnettLawns 3 жыл бұрын

@@JustinJoyinglife oh I see. No I don’t think it would be enough leverage. The bolt head is very shallow. A really long beaker bar with a 1” extension is best. My extension was 2” and a little too long for a perfect angle.

@Pure_KodiakWILD_Power 3 жыл бұрын

Been awhile, brother. Was it you I recently saw on a 5 year old truck repair video on some sort of diesel channel??

@Pure_KodiakWILD_Power 3 жыл бұрын

Might have been a rear diff video; I think that's what I was most recently looking up....

@GwinnettLawns 3 жыл бұрын

@@Pure_KodiakWILD_Power Probably I have a channel that is my main one called dieselworld

@Pure_KodiakWILD_Power 3 жыл бұрын

@@GwinnettLawns yeah, that's it 😂 I _thought_ that was you.

@keithwallace-bi6xr Жыл бұрын

What is the part number for the hydro drive belt?

@GwinnettLawns Жыл бұрын

I dont have the mower anymore so you will have to Google it.

@victorrippe5845 3 жыл бұрын

Thanks for sharing my dealer charged me $45 to change both belts im using Stens blade belt cause the oem only lasted me 300 hours also and im on1105 hours the Stens belt has 805 hours already and its in perfect condition and i get them in Amazon for $29 let me know if you want the part number for the Stens belt.

@chewarmstrong 3 жыл бұрын

Yes what’s the part number? Thanks!

@chuyroman2046 3 жыл бұрын

Maaann looks like a pain in the ass! There is absolutely no room down there. I just got a new stander x 52 and a simple oil change is so difficult bc of the lack of space.

@GwinnettLawns 3 жыл бұрын

Yea I agree.