How To Correctly Adjust A Motorized Bike Clutch

Рет қаралды 88,909

3 жыл бұрын

How to correctly set up, adjust, diagnose, repair, and maintain a clutch system on a 2 stroke motorized bike.
If you have a more advance clutch issue, just out this video: • Motorized Bike Clutch ...
How to split the case if you need to dig deeper into the clutch shaft or bearings: • How to take a bicycle ...
We upload motorized bike videos every week (sometimes more)!
FAQs:
Oil: 32:1, semi synthetic, random brands.
Gas: 87oct
Spark Plug: NGK B8HS (yd-100), NGK B6HS (pk80)
Parts: I buy mostly from Amazon.
Favorite Motor: Zeda (Firestorm) Triple 40
Favorite Carburetor: NT Speed
Favorite Bike For A Motor: I don't have one yet.

Пікірлер: 264

@king49334 3 жыл бұрын

i find that clutch shaft assembly wear out. the ball bearing inside it will wears out the shaft.

@LAHover 3 жыл бұрын

I have never had that issue, but it does make sense. Good call

@doccpu7 2 жыл бұрын

Doing a new install. no matter how you pull on the clutch lever even with a 2 foot bar it will not loosen the clutch. Can they freeze up? dhorner@usa.net

@Spacecruizer203 2 жыл бұрын

@@TA-xj5we my clutch is stck it wont disengage

@Spacecruizer203 2 жыл бұрын

@@TA-xj5we im gonna just get a yd100 an put this aside for a lil it got me over 3k miles for 100 bucks she did her job for now its a triple 40 pk80 thnx for your reply

@Spacecruizer203 2 жыл бұрын

@@TA-xj5we happy new year by the way

@user-kn8oe8zp3n 4 ай бұрын

This video is superb! I ended up throwing out an engine, due being unable to figure out why the clutch wasn't disengaging. If only I had watched this sooner... This is the ultimate guide to clutch problems, and prevention. Thanks so much!!

@markwatson1970 3 жыл бұрын

Just adjusted my clutch incorrectly. This clarified things. Great job.

@LAHover 3 жыл бұрын

Hey sorry I'm late, I just saw you video, Is it still slipping?

@markwatson1970 3 жыл бұрын

@@LAHover yes, slips. I’m sure I overtightened the flower nut just to get some grip. New erasers, and tightened the inside(shaft?) spring , 1’ plus by rolling the bike backwards. I scuffed up the clutch plate a bit to increase grip, I put in a slightly longer clutch push pin that touches the ball bearing to compensate for the flower tightening. I noticed a lot of play on the clutch large sprocket. Could this cause my slipping? I’m stumped. I can get the bike going but it takes a bit of low speed peddling.

@LAHover 3 жыл бұрын

@@markwatson1970 Side to side play in the large bevel gear is a sing that the tiny friction plate bearing may be failing / falling out, but as far as I know it wont cause slipping. Once you get the bike started does the clutch still slip much during acceleration?

@markwatson1970 3 жыл бұрын

@@LAHover it accelerates fine and behaves once I get her going. It’s the initial grip to turn over the engine that seems to be lacking.

@LAHover 3 жыл бұрын

@@markwatson1970 I'm starting to think your motor may have great compression. Try these pads instead www.amazon.com/dp/B095HLBWFN/ref=cm_sw_r_cp_apa_glt_fabc_PX8M165D4VKPG5QHRV5R I have seen people make their own by cutting car brake pads as well... I'll be trying it in a near future video as well.

@Mr._Darby 3 жыл бұрын

I can't believe that he let his coffee get cold.....lol

@christopherbozeman6333 2 жыл бұрын

I know right James, but much like me I get distracted by work or talking. If it was good coffee he wouldn't have let it get cold.

@jaxknet 2 жыл бұрын

Thank you for all of your content! I had never worked on any 2stroke anything, or owned a motorized bike. I slapped an engine kit onto a mountain bike that I've had for years, and it flies! It's thanks to you help and in depth explanations that I'm getting more comfortable with adjusting clutch, etc. Just had to say thanks again and keep up the wonderful content :)

@badbadbob1 3 жыл бұрын

Very well thought out, This video should help with identifying what was not only wrong with the clutch but even better stop issues by setting it up correctly. Thanks

@soggyridesmotorizedbicycle6258 Жыл бұрын

Thanks for being so thorough on the clutch assembly. It was always something that I shied away from. It was easier once I saw one taken completely apart. I appreciate your explanations too.

@user-oj4os3rl9n 2 ай бұрын

I love this guy he is very specific and give me a lot of details

@warlock.420 Жыл бұрын

Your troubleshooting and repair videos are the sht! So happy you take the time to explain what to do and why. Your videos are gold my friend!

@elliottbamforth9477 2 жыл бұрын

Very informative video answered all my questions with all the issues that I'm having with my bike. All the issues that I was having with my clutch he answered them and they were very easy to understand. The most informative video I've seen yet

@gherosh 3 жыл бұрын

Very good video! It takes a while to figure out all this things, you never find them in user manual. Thanks for sharing!

@rcadventures4342 4 ай бұрын

The best clutch tutorial I’ve seen, thanks…

@grant_mayer Жыл бұрын

Great video!!! I’m new to motorized bikes and had to adjust my clutch, this video helped me so much!

@bryduhbikeguy 3 жыл бұрын

That's a Really great video.Thank you.I use a magnet to pull the Bucking Bar and Ball Bearing together.1st time I wanted to re-grease I figured that out quick.LoL.When I installed my 2nd motor I removed the assembly that holds the cable end over the clutch shaft and squeezed in about 2 tablespoons of Gear Oil for that area.

@skeeter06b 3 жыл бұрын

Nice video. Been having clutch problems and after watching your video I understand what I was doig wrong. Nice information Thank you.

@Everatti 3 жыл бұрын

I rebuilt the entire clutch assembly on my motorized bike about 2 weeks ago. Really wish I could have seen this first 😂

@Everatti 3 жыл бұрын

Also, can you cover the internal clutch shaft, spring, etc. I feel like it plays a big role in the clutch feeling and adjustment, but always gets overlooked. Sometimes, the issue is beyond the bucking bar, flower nut, cable tension, etc.

@jayclutch6533 Жыл бұрын

How long did it take you

@CuddlyJon 2 жыл бұрын

Thank you so much man. For a long time, it took me a while to start my bike up. I thought it was because the motor had to "warm up" or I wasn't giving enough choke or what not. Little did I know, my clutch had been slipping since the beginning. I needed to adjust my inner collar nut. Now, as soon as I let out the clutch, she springs up to life!

@LAHover 2 жыл бұрын

If you still have slipping issues check the video description, there is an advanced repair video link.

@donaldgtidwell2198 Жыл бұрын

Thank you for explaining things as you go, I'm new on these motorized bike, I bought one off a friend at work, he sold it cheap because he had it all apart in 2 boxes, I've never put anything like this together I almost told him I'd pay him more just to come get it, but I began to watch your video and a couple more others and in my amazement I put all together, so thanks again, if I had to take it somewhere to have it work on couldn't do it, your very understanding my friend.

@traehodges3796 7 ай бұрын

I used an Old drill bit as a bucking bar as I lost mine I just used the the same diameter drill bit as the bucking bar cut the drill bit off obviously and used the part that sets into the drill it seems to work fine and is holding up fine better then the stock one alot stronger material

@michelevitarelli Жыл бұрын

Thank you for taking time to make this informative video. Great job.

@adognamedbird 2 жыл бұрын

Perfect video man. Gonna have to share this in the FB groups!!🤙

@JohnWaldron-cm7ce 9 ай бұрын

Great video! I so agree about the clutch lever cam assembly being assembled too tightly. Mine has very little "wiggle room" and I don't have any puller to disassemble it. I ordered another one that's disassembled, so hopefully I can assemble it with more cam shaft/bucking bar play-John in Texas

@darkisato 2 жыл бұрын

thx for ur tips I just built my 1st motor bike and had a issue with the engine not engaging. after watching this I learned my clutch lever was not adjusted properly. once I redid the arm it turned over perfectly thx!

@MrJoeltrain Жыл бұрын

I have burned up about 10 bucking bars. I finally found that WHITE LITHIUM GREASE works very well. I want everyone to know this as I have been stranded due to a melted bucking bar on more than one occasion.

@richardsaddress580 Жыл бұрын

13:30 Good info on the "neutral position" of the bucking bar and where to grease. Thank you, sir.

@OhCanadathebest 2 жыл бұрын

Thanks man. U the only one who clearly teaches whats up cheers from Canada

@micahgoingback1771 Жыл бұрын

A needed video for everyone that has a motorized bike. Wish I saw this year's ago

@awesomenotadick 3 жыл бұрын

Nothing wrong with my clutch, I just like watching these videos.

@JewelsYulieDiaz-go1rz 11 ай бұрын

Great explained clutch video, excellent information,thank you

@ronreiff3991 6 ай бұрын

O.M.G! Thank you so much for knowing that ingageing the clutch is when you pull the lever in ! I've had so many arguments about this....

@Willy7212 2 жыл бұрын

Thank you for the information. Very well explained.

@robertoreyes3956 2 жыл бұрын

I never do comments this is my first one ever... but this deserves it .great video wish more people did them like this... again thank you for going over everything and specific reasons why

@curtisjohnson7023 2 жыл бұрын

This information is invaluable!! Thank You So Much!!

@kimdecastro9156 3 жыл бұрын

another good video excellent in to detail.

@robmorefield5950 2 жыл бұрын

Thank you so much for your detailed video 🙂

@keeganhache6667 2 жыл бұрын

On my clutch cam for a quick fix I sanded it flat so it would engage again works well

@wesmccallum5728 11 ай бұрын

That was a great tip bud.. the only thing I haven't figured yet on my kit bike..

@fredmitchel1236 Жыл бұрын

I see why a new engines is sold for $99... Amazing the big power from 60 cc is only like 4 HP tops... My old Suzuki 50 cc...vintage 1972....a 3 speed auto transmission and put out close to 3 hp....and lasted years....quiet smooth and fast 😮

@josefernandes9655 2 жыл бұрын

Very good video! I had a issue just in first time I ride the bike, and I after see you video, I think was because of the cluch point tha was wrong. Thanks

@kimdecastro9156 2 жыл бұрын

thank you for this video . and your other video. im a first time builder .they help me out a lot.

@LAHover 2 жыл бұрын

Glad I could help. And good luck Builder!

@user-oj4os3rl9n 2 ай бұрын

I actually fixed my bike within an hour after watching this video

@codelicious6590 3 жыл бұрын

A couple of the replacement bucking bars I've gotten on Amazon have been too short, leaving me wondering what the heck I had done wrong. I found one that actually gave a measurement and sure enough, when compared to the previous ones I had gotten, it was a few MM longer!

@heartisblind 2 жыл бұрын

Thanks a lot..You saved my clutch...

@richiewheeler1810 2 жыл бұрын

I appreciate your very detailed description of what each part is and how it works together with the whole system. This video has helped me greatly. Thank you

@szerediferiFrumuseni 2 жыл бұрын

🤩🤩🤩🤩Frumos si bine spus...merci domnule.. De la tine am învățat multe legat de 2 stroke..Pe primul motor lam distrus făra sa știu nimic ,și am distrus și roți pe spate din cauza tensionerului de lant...Al doilea motor merge perfect ,am facut așa cum ai spus tu domnule...Mulțumesc frumos...din Romania,Europe..

@motorizedbicyclerider5296 3 жыл бұрын

👏👏👏👏 well done on the video 🚲💨💨💨 and information on the clutch and the bucking bar I have had that problem before thanks 💨💨💨💨🤙👍💯

@motorizedbicyclerider5296 3 жыл бұрын

Welcome 🚲💨💨💨

@Spacecruizer203 2 жыл бұрын

my back wheel is stck moto rider the clutch wont make the small gear turn it wont disengage

@motorizedbicyclerider5296 2 жыл бұрын

@@Spacecruizer203 did you get it figured out

@Spacecruizer203 2 жыл бұрын

@@motorizedbicyclerider5296 not yet im thinking the piston might be stuck i went to the store shut the bike down came out and the clutch wont disengage its stuck

@motorizedbicyclerider5296 2 жыл бұрын

@@Spacecruizer203 it's kind of hard to say it could be any little problem you'll just have to take it apart

@sparkiegarage8083 3 жыл бұрын

I like that piston just chillin up there

@Ozzieseth 3 жыл бұрын

Also another reason your clutch might be slipping might be the small drive gear. How I fixed it was I got a bolt and put the head of the bolt against the bevel and drive gears to lock the motor up. Then I tightened up the bolt and that fixed my clutch issues

@LAHover 3 жыл бұрын

That gear should be keyed as well, but if the fix works for you that's great.

@alexj.alexander2036 2 жыл бұрын

Hey man I appreciate your videos. Very helpful, because you are in fact very knowledgeable about these motors, and other components regarding these makes. I would like to go into business with someone like you!

@LAHover 2 жыл бұрын

Thanks builder!

@halethewhale 2 жыл бұрын

I use heat shrinks as a cap on clutch cable it's handy, you can still get cable out without removing anything

@hcgrain7231 3 жыл бұрын

Great video

@bernieolivera5632 7 ай бұрын

Your video is very good. My question is. The inner bearings on each side went bad. When I remove the clutch assembly some of the ball bearings fell out. The bearing races are pressed in. My question is simply how do you take these races out so I can put new ones in. Tried heating the bearings with a propane torch. Then I tried knocking them out with a hammer and chisel. Didn't work. Any ideas?

@rockytransaman8288 Жыл бұрын

I did like the video as it is very informative. Not sure if I'd fallow you on fastening the gas tank to the top frame bar technique. I guess that the little bolts were broken or stripped. If so, I'd have replaced the tank.

@Nvent1 2 жыл бұрын

Thank you so much, I think I found my problem because of your video. What kind of Grease do you recommend?

@noorhantoosh_5928 2 жыл бұрын

Hey man, I recently got a motorised bike that’s brand new and I tightened the wire for the clutch arm good and the clutch arm didn’t move. But when I pulled in the clutch the clutch arm got loose. Is there any easy fix to this?

@siklistademakina 3 жыл бұрын

nice! this is good info, need to adjust my clutches too.

@chavvis447 2 жыл бұрын

Hello, how about if my chain broke and I replaced the chain and took off the lid of the clutch and now I have to adjust the arm of the cable clutch, how can I know when it's properly engaged, so I can started?

@FromSaultoPaul 2 жыл бұрын

New at this as I want to build a 4 stroke. Do I need a Jackshaft with a clutch assembly if on comes with the motor? Some motors come with a clutch assembly from Bikeberry for $299.

@ChuckHaney 3 жыл бұрын

Your videos have fallen off of my KZfaq radar for some reason. I'll have to go back and watch the three I've missed.

@ChuckHaney 2 жыл бұрын

My clutch arm has to be turned in WAY past neutral before it gets close to touching the bucking bar. Do any of these engines use two bucking bars? One smaller than the other? It may be a false memory but I thought when I first got this (PK 80) that there was a big bucking bar, a bearing and a smaller bucking bar but if it did, I lost the smaller one. My bike has less than 10 miles on it and the bucking bar is already very rounded over.

@1071obr 2 жыл бұрын

I have a 125cc toatoa go kart that grinds in reverse but works well in the forward gears. Would replacing the clutch likely repair this issue? I haven't been able to find anyone who wants to repair so I will probably have to do it.

@randomprecisionmotors3130 3 жыл бұрын

Question: why does my clutch 'grab-slip-grab' to the point where the engine won't start because I can't get a full revolution of the crank to fire it off? I'm thinking the Clutch plate is either warped, or it's possible I could have over-greased the Bevel Gear, and some grease may have contaminated a few Clutch Pads? The Engine is a MaxInd YD100 with zero hours...

@lemonaid665 Жыл бұрын

My clutch is extremely stiff and hard to pull. I’ve changed the cable routing and removed the return spring but it’s still the same. Anything I can do? Maybe the clutch spring?

@Mrbotlegmechani 3 ай бұрын

Ayy hover what material is the black clutch pads made of am quite paranoid that they may be made of asbestos so everytime i touch or get near em i use a mask and glove if you may pls tell me just for clarity of mind 😅

@MikeFATBOYZMichaelidis 3 ай бұрын

where does the bearing go? i thought my bar and clutch were shot... there seems to be a lot of metal shavings inside. Recommendation on what grease to use

@cachaitos 2 жыл бұрын

Thanks for the great video! What kind of grease do you recommend for this purpose?

@LAHover 2 жыл бұрын

I like Lucas Red N Tacky.

@patsmotorizedbicycles6943 Жыл бұрын

What kind of setup do you have for your bicycle engine exhaust clutch and electrical

@KevinTodd 3 жыл бұрын

Great video I'm in the process of building my new engine and all bearings clutch included and I have never changed bearings in the clutch I didn't know you used that tool to do that thanks.

@lachlanbruce5566 3 жыл бұрын

Cut grooves into the pressure plate really helps getting the clutch to grip

@LAHover 3 жыл бұрын

I'll have to try that, I have an old set of pads, I'll see if it brings them back to life.

@jaredbourgeois4722 Жыл бұрын

I've learned that if I take my new upgraded clutch pads and pass the outer edges on a grinder just to smooth the edges out they move towards the inner clutch disc better and bite on both sides better.

@LAHover Жыл бұрын

Interesting, thanks for the suggestion.

@DaleBladez 3 ай бұрын

2:07 I run a spring over the cable between the clutch lever and the cable tube. The excess cable I then tuck into the spring so it doesn’t stick out and poke me or fray.

@devincanales3406 Жыл бұрын

Well when your riding how do you know when your clutch shaft has been shot completely? When I ride mine it just started where I hear a heart dropping grinding when I pull in the clutch and it didn't wanna go over 12mph I even had to help it go up hills

@LAHover Жыл бұрын

Good news, easy fix. Bad news, it sounds like your clutch basket bearing failed/migrated. I can't say for sure tho.

@rileyplamondon8095 2 жыл бұрын

Ok, I went through 3 camshafts that had completely worn out. I welded one back and that always stayed in one piece, but now I have a new issue. First of all I have no tension in my clutch lever, the bike doesn’t fire until low speeds. When it does for it slips on the plate because the ram stays the same until it heats up and than it grabs but have only ran it twice like that. Now I have figure out what’s wrong but not how to fix it, the pin that the flower nut attaches to is not moving in and out with the pull of the lever. Any idea what’s wrong?

@LAHover 2 жыл бұрын

Check out the video linked in the description. It covers more advance issues. Good chance yours is in it. Good luck!

@Michael-le4dc 3 жыл бұрын

Do you know some good stores I could find the better clutch pads to replace my eraser pads? I am frequently hearing my clutch make a squeaking noise and when I take the cover off I can see the clutch slip.

@bryduhbikeguy 3 жыл бұрын

I bought a clutch disk With the pads like his already installed for $12 ish off Amazon in the 'Motorized bike parts etc.' section so I have 1 when needed.

@Michael-le4dc 3 жыл бұрын

@@bryduhbikeguy ill look into that thanks

@TheAverageMiz Жыл бұрын

I've seen souder on the end of the clutch cable works good

@kjohns1413 3 жыл бұрын

For some reason I always thought the clay red ones were the best ones. I hate the chirp they make though. I'll try the re-used rubber tire ones again.

@oimpastato 3 жыл бұрын

Well done! Thank you. Have you ever find the need to adjust the inner spring on the clutch shaft? I know you can remove the cable holder, and place a sizable punch and move the rear wheel forward / backwards to help adjust. Figured I'd like to hear your opinion on that, and Thanks again for the channel & your wisdom. :-)

@LAHover 3 жыл бұрын

I never have. I did have it in the original upload but I had to cut it out because I mistakenly said "move the wheel forwards" lol opps

@seanrallis6714 2 жыл бұрын

I have a new build, and it keeps destroying bucking bar bearings. I grease the ball bearing every time, but within 5 miles, the ball bearing becomes a half-sphere. This has been driving me insane for a week, since I got the bike. I have gone through 4 bearings already, and I grease the hell out of them every time. Any idea what can cause this?

@edj9202 2 жыл бұрын

How do you get the clutch arm on the the clutch shaft the grooves it's like the hole is too small

@devancook132 2 жыл бұрын

How do you set up the clutch play in set screw on a new build

@gordiepeck4364 2 жыл бұрын

I need to adjust my clutch after every ride, do you know why this might be?

@jimlee1770 Жыл бұрын

What type of noise can clutch assembly make and how do you correct them ?

@MrJonathandcrow 3 жыл бұрын

Thanks LA

@rahimwillson6566 2 жыл бұрын

When I pull in my clutch the whole bevel gear and shaft moves in the case?

@daleyoung87 2 жыл бұрын

Instead of having a flat-sharp area on the clutch arm, they should have shaped it like a cam lobe.

@edkiggans1626 Жыл бұрын

I just bought the 100cc 2 stroke motor. The clutch will not engage. The crank won't turn. It's not locked up.i need help with it.

@martianmanhunter7925 2 жыл бұрын

My bucking bar sticks far too out and the ball is stuck inside where the bar goes any help please.

@benjimandover8072 2 жыл бұрын

I gotta 80cc anbul kit... I got it to start once...every time after the clutch just slipped...I adjusted the flower nut and the spring under the clutch cable routing point and it still slips...my pressure plate looks like the engagement is lop sided...Its the pads are all black from the slipping...can you help me

@LAHover 2 жыл бұрын

1: Make sure the set screw that keeps the flower nut from spinning is not to long (pushing on the basket). 2: Make sure the woodruff key is not missing or striped where the shaft meets the basket. 3: You may have a more advanced issue, this video may help. Good luck kzfaq.info/get/bejne/pp9ihdR_zd7Zg3k.html

@user-vb2im9ik7h 8 ай бұрын

Where do I buy the clutch for my 29 gx7 Genesis and the big gear too

@Johnjohn-eo6mb 4 ай бұрын

What happened if I don't use Round Column Bolt for the small bevel gear you think my clutch start slipping

@elliotdownie7431 Ай бұрын

Does anyone know if it is possible to fit the drive sprocket onto the clutch so that I could run a chain to my bicycles original gear setup? That way I won't need to use a jackshaft thanks

@merakki 3 жыл бұрын

I got a new bike with motor and it Jerks repeatedly when I slow down kinda hard to explain in text format.Not sure if its cause of new motor but I'm thinking its something to do with clutch.If you see this any idea what I'm talking about?

@LAHover 3 жыл бұрын

You may be reaching stall speed. Once you drop below about 8-10mph the motor will chug. It also plays hell on the chain, pulley, and sprocket. If you want to ride slow you will need a bigger rear sprocket.

@rauljrcelis5618 2 жыл бұрын

How can I take barren out of the clutch.. if it's pushed in n not coming out

@edkiggans1626 Жыл бұрын

I just got 100cc engine running. May I have have the part numbers for the clutch components! Thank you.

@edkiggans1626 Жыл бұрын

This video was very very helpful. 👍👍👍👍👍👍👍

@jarencreations7003 2 жыл бұрын

I really need help I bought a motorized bike kit put everything on and got it working and I tried starting it and the clutch just slips so I did lots of adjusting with the flower nut so that I can idle still with the lever all the way in and the clutch wouldn’t grip even with the clutch tight. I have new pads to put on it even tho I only have about 5 hours on the bike.What should I do?

@LAHover 2 жыл бұрын

In the description of this video is a link to my more advance video that might have the same issue as your build. good luck I hope it helps.

@jarencreations7003 2 жыл бұрын

@@LAHover okay thank you I will go check it out

@joneserupinsmoke9161 2 жыл бұрын

Hey does anyone know why ny engine putters when I 1st start it.i cut muffler ran straight pipe and cut the side of air case off .I tried to mess with carb but the only way it stops is if the idle is high .I dnt like to hear it like that but if thats what needs to be so be it

@MrBri_Guy 10 ай бұрын

What does it mean when I pull in the clutch and I feel resistance in gliding? Can that mean my pads are bad? Also I hear squeaking. Help!

@donaldgtidwell2198 Жыл бұрын

Thanks!

@alexaseltine1052 2 жыл бұрын

How do you fix a stiff clutch sprocket for the motor chain

@Motorizedmonster413 2 жыл бұрын

Can a poor adjustment or slipping clutch cause a really loud screeching noise? As soon as I let go of clutch it makes a nails on chalkboard shreeching noise. Brand new 66/80 bbr engine..

@LAHover 2 жыл бұрын

I have one motor that does the same. Screeches when engaging the clutch but stops once fully engaged. I think it's just the pads... Should not hurt anything, but a new set of black pads should fix it.

@Motorizedmonster413 2 жыл бұрын

I should replace the pads even tho it's brand new? And is that definitely the problem I'm having,?, Maybe some grease on the gears would help? And when I get to 10-15 mph it doesn't do it when I let go of throttle it starts to kind of stall out or kind putter . I do have oil coming out of top cylinder and exhaust and would this have anything to do why my throttle is low/bogging. Sorry for all question this is my first build

@LAHover 2 жыл бұрын

@@Motorizedmonster413 well see I can't hear your motor, and I don't have much to go on so I can't say.