How to remove replace passenger right cv axle 2004-2009 nissan quest

Рет қаралды 44,580

4 жыл бұрын

passenger right cv axle:
amzn.to/3qdTbyA
I mispoke in the video . This is not a sealed transmission. Had my facts mixed up its the filter that is not serviceable but the fluid can be drained and refilled .

Пікірлер: 74

@ah7908 2 жыл бұрын

Thank you for showing where you place the jack and supports. First video I've seen that shows that.

@s33therfan 2 жыл бұрын

Thank you for the great feedback and thanks for watching.

@shemlanjan411 2 жыл бұрын

Great video. Thank you for showing everything step-by-step. Great job.

@s33therfan 2 жыл бұрын

Thank you for the excellent feedback, much appreciated.

@jamesbroomfield7799 6 ай бұрын

Very very great vid. Straight to point and detailed what to expect in real time.

@s33therfan 6 ай бұрын

Thank you very much.

@shootlightsout 4 жыл бұрын

thank you sir! you helped immensely with my stuck cv!. 14:34 to 17:00ish removing the bracket itself was key. then pb blaster and a mallet and stone chisel to separate the bracket and the old axle. not a fun job on a car in salty snowy east coast state.

@s33therfan 4 жыл бұрын

Thank you for the great feedback and thanks for watching

@rong609 11 ай бұрын

This is the best video of mechanic work and explanation

@s33therfan 11 ай бұрын

Thank you so very much.

@baxrok2. 4 жыл бұрын

NIcely done sir! I can't believe that you got it out by just banging on that flange. haha Nice break for you. Thanks!

@s33therfan 4 жыл бұрын

Yes , I was pretty proud of myself . Everything seemed to work out smoothly and I managed to keep from breaking anything ha . Thanks again

@peacelove8941 3 жыл бұрын

Honest n good teaching video. Thank u sir.

@s33therfan 3 жыл бұрын

Much appreciated . Thank you for watching.

@haroldeby2652 4 жыл бұрын

thanks dude for a very detailed message

@s33therfan 4 жыл бұрын

Thanks for watching

@kurtwall223 4 жыл бұрын

Nice work. Compared to many other gearhead videos yours is high quality. Camera work showing bolts was impressive. If you can, try editing software that will allow you to draw in arrows to "point" at what you are talking about. Very good job with your video Sir, thank you.

@s33therfan 4 жыл бұрын

Thank you for the great feedback and the helpful information I appreciate it. Thanks for watching

@kurtwall223 4 жыл бұрын

@@s33therfan No problem. I had do this repair and your video was a huge help on my '06. Been turning wrenches since '99. Havent paid a shop for a thing since then. Guys like us manning up, thats what it's all about.

@lou4774 2 жыл бұрын

Used your video to replace my gf's Quest passenger cv axle (torn boot). Great video and step by step instruction. Living in CA I was able to remove the CV axle without removing the bracket. Nevertheless, and great how to. 3 hr job for me as I move pretty slow and deliberate with new projects. Thanks!!!! Also had to use a piece of pipe with the breaker bar to break the axle nut loose. Correctly torqued it upon reassemble.

@s33therfan 2 жыл бұрын

Thank you for the feedback , much appreciated.

@SheyzFrancis 2 жыл бұрын

Where do you live in CA, I have same problem with my 2007 quest. Need to change the passenger side CV axle

@psykolyko 4 жыл бұрын

Excellent video Well detailed instructions Thanks friend 🙂👍🍻🍻🍻

@s33therfan 4 жыл бұрын

Thank you very much for the great feedback and thanks for watching

@felipemerlos2409 4 жыл бұрын

Thank you very much, the most helpful tip for me was how to know if the trans is a 4 or 5 speed, again thanks very good video.

@s33therfan 4 жыл бұрын

Thank you for the kind words and thanks for watching

@Rennyblood10 Жыл бұрын

Make more videos you are good at showing everything

@s33therfan Жыл бұрын

Thank you very much for the kind words and thanks for watching.

@cubancruz6303 4 жыл бұрын

Thank you, very helpful

@s33therfan 4 жыл бұрын

Thank you for the feedback and thanks for watching

@theodorecrick6974 3 жыл бұрын

Great video. I appreciate the detail and step by step instruction. Now how much would you charge to change mine? :)

@chellob11 3 жыл бұрын

Thanks for the tips .

@s33therfan 3 жыл бұрын

Thank you very much for watching.

@leorobinson5737 3 жыл бұрын

Great job, thanks.

@s33therfan 3 жыл бұрын

Thank you for the great feedback, it is much appreciated.

@dawadahbanyahawadah1495 3 жыл бұрын

Awesome thanks a lot bud.

@s33therfan 3 жыл бұрын

Thank you very much for the great feedback , it is much appreciated.

@ahmedsaidu-kamara6760 2 жыл бұрын

Great video. You showed great temperament in not get frustrated when it didn't come out. I'm having the same issue with my 2010 Nissan Maxima but I've only located 2 of the bracket bolts that's mounted to the engine. Plus it's very cold now so working outside is very hard. Where online can I find a 3 feet extension and your swivel head? By any chance, do you know how many bolts hold that cv axle bracket that's mounted on my 2010 Nissan Maxima? I think with patience I can find it. Watching your video has given me the confidence that I can complete my car project this week. Thank you.

@s33therfan 2 жыл бұрын

It looks like there are atleast 5 bolts going through yours and possibly an altetnator or pwr steering pump sitting on it. Here is a link below so you can get a better image of the bracket , and a link for the extenison. Thank you for the feedback. www.ebay.com/itm/OEM-2007-2014-Nissan-Altima-Maxima-Front-Drive-Shaft-Bracket-NEW-39780-JA100-/203260121466?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=711-127632-2357-0 amzn.to/3JDgUPa

@ahmedsaidu-kamara6760 2 жыл бұрын

@@s33therfan Thanks but there's no way I'm going to take that bracket out when you said another part sits on it. I might have to heat up the bracket to separate the cv axle from it or take it to a repair shop. If you have any suggestions to separate without removing please let me know, thanks.

@s33therfan 2 жыл бұрын

I would recommend one of these tools , but other than spray lubricant and trying to hammer it out , I can't think of another method. This slide tool gives a lot of force with the hammer action. amzn.to/3JAjQfw

@differentvibes8200 4 жыл бұрын

This was very helpful, thank you so much, just need the name of the sensor you broke as I broke it as well 🥶

@carlosa.zuniga6987 2 жыл бұрын

Hello, I also broken it, do you not de name of the sensor ?

@bones6244 2 жыл бұрын

It looks like the knock sensor

@bones6244 2 жыл бұрын

Google it for our specific vehicle and it should look very similar imma say it is the knock sensor because of the 1 prong plug

@Go-T.7824 Жыл бұрын

Do you have a video on doing the driver side of a Nissan quest

@vk17171 3 жыл бұрын

Thanks for the Video. I will be doing this project soon on my 2008 Nissan Quest same passenger side. I see that you did not remove the tie rod end and underarm control ball from steering knuckle. I see some of the videos removing them, I am not worried about underarm but wondering on tie rod as the steering knuckle with bearing hug may put some weight on & may cause any damage to it. Appreciate it!

@s33therfan 3 жыл бұрын

This is how I always remove mine . Thanks for watching.

@vk17171 3 жыл бұрын

s33therfan Ok. How is it holding up far? Any issues with the broken sensor? Thanks again for the video. It helps a lot for DIY starters like me.

@s33therfan 3 жыл бұрын

The sensor was actually fine , it only bent the plugs over slightly and they straightened back out no problem. Thanks again.

@leorobinson5737 Жыл бұрын

Nice video, thanks for sharing. Would 04 Quest driver's side similar and do I need to remove the ball joint?

@s33therfan Жыл бұрын

Yes , it will be the same procedure except you will have to pop the cv out with a crow bar/pry bar , because it is held by a clip . Thanks for the question.

@leorobinson5737 Жыл бұрын

@@s33therfan much appreciated, thanks a million.

@12MRJERSEY 4 жыл бұрын

Impossible for 7th gen Maxima. I have a 14' Maxima. I've lossen all the bolts (4 total) holding the housing and it can not be remove because of the tight spacing. The only thing left to try is a slide hammer.

@frankamaton8016 4 жыл бұрын

Would this cause the van to not drive forward or reverse when put in gear if the part is broken?

@s33therfan 4 жыл бұрын

If its separated or severed it could. You could observe this by looking safely on either the passenger or drivers to see if its spinning freely . This applys all the output to the broken axle . It could also be an issue with the transmission as well . If the axles are fine I would start by checking the level of trans fluid . Hope this helps out and thank you for watching.

@george11694 Жыл бұрын

Did you lose transmission fluid ??

@TolaTrucking 3 жыл бұрын

I don't think that missing bolt backed off...probably being harder to get to last teck that worked on it just left it out. Great job on the video.

@s33therfan 3 жыл бұрын

Sounds about right , Thank you for the great feedback and thanks for watching.

@Barryd57 4 жыл бұрын

Can u just replace the boot w/o replacing the entire axle?

@s33therfan 4 жыл бұрын

You can just replace the boots. When I have priced the boots they usually were not a lot cheaper than the entire cv axle , that is one of the draw backs. The other in this case was the cv axle itself was in bad condition . Bad to the point of causing vibrations. So in summary if its just cracked and the cv axle is fine then replacing the boot may be a good option. Usually they come with new axle grease etc. Great question and thank you for watching

@kwangyi2134 4 жыл бұрын

I must not be reading the manual correctly. 2006 Service Manual - FAX (front axle) have 125 ft-lb of torque on 32mm Axle nut.

@vk17171 3 жыл бұрын

Its Newton-meter. N-m(kg-m, ft-lb) = 125(13,, 92). 92 ft-lb is correct.

@tnoutdoordudes 2 жыл бұрын

Did you have to get the front end aligned afterwards

@s33therfan 2 жыл бұрын

I did not. Having an alignment is always best after working on or replacing front end parts. There was no uneven tire wear or issues in my case .

@carlosa.zuniga6987 2 жыл бұрын

I need help what’s the name of the sensor? I also I broken it I need to replace

@bones6244 2 жыл бұрын

I think that is the knock sensor

@victorramirez1920 3 жыл бұрын

how to know if it is a 4 or 5 speed

@s33therfan 3 жыл бұрын

I know I had the same question and I believe I found the number stamped on the transmission . There may be an easier way and someone else can chime in . Thanks for watching.