Hey Bill -- you're at a decade and still helping people. This was the most accurate, realistic, and helpful belt replacement vids I've seen. Thank you!

9 years later and your video is still helping people, thanks a ton 👍

Dear Bill, We have this exact dryer. Your videos were invaluable for repairing it. The roller bearings were gone. We decided to replace the belt as long as we had the machine apart. I was dreading reattaching the belt but after watching your video and following your instructions it was super easy. Thank you! Your videos save us a lot of money by repairing it ourselves.

Thank you!!! I was trying to put it on the black wheels and my dad gave up saying he was gonna buy a new dryer until I watched this video! So now my dryer is fixed! I fixed it 🤣🤣🤣🤣 so thank you

Thank you very much! I could not for the life of me figure out how to properly connect the dryer belt to the motor shaft/pulley and idler pulley until watching your explanation. Using the left hand to raise the pulley and the right hand to pull the belt UNDER the pulley wheel and then connect to the motor shaft/pulley was the key. I watched several other videos, read numerous explanations, and looked at many illustrations but not a single except yours actually explained how to do it.

40 minutes I've been trying to figure out the belt configuration. Thank you!

Thank you. You seriously have no idea how much you have helped with your straight forward direction and good visual on all the parts. Thank you so much

You saved the day showing the schematic of the Belt. I had everything else right but couldn’t get the configuration right. Thank you!

Bro you saved my life and taught me something new ,much aloha from hawaii ,I feel very accomplished !! Thanks man really !

Thank you, Bill! I was struggling with how to get that belt back around the tension thing once the drum was in place. I didn't swear once because your video was so easy to understand. Great video!

I was combing the Internet trying to figure out how to route my new drum belt and it became laughable how every article or video omitted this crucial detail. Thank you Bill, you are the bomb, Sir!

Mr. Newberry I just want to say thank you very much. This was my first belt change and with this video I was able to repair my dryer and save my self alot of money.

HUGE appreciation-watched this 10+ times & finally got it. its alittle stiff spinning but i esriously cant remember if it was always like that. my very old de410 had a small but effective backdoor & i used duct tape to hold the right side down over the drum-removed after attached to the thing with the spring & motor round thing. You made a nearly middle-aged woman very happy (and filthy dirty)-THANKS!!!!!

BOOM...to the point and an excellent aid...I watched your disassembly also...great and simple. I just needed to clean out the lint build up inside. Thanks for not taking 45 minutes, explaining the concept of dryers, why people use them, how many models are available...etc., etc!! Great Job!!!

I never touched an appliance to repair and out of all the videos, this one was the most detailed and thorough which helped me to replace the idler roller and put a new belt on the drum. Now I have to find a video to help me put the front back together. Thank you Bill! Carol

I have Been working on my dryer for 1 week all these other videos confused me yours was so clear and helped me 100% thanks so much

Excellent! I figured, how hard could it be? Thank God I found these 2 videos. So easy to follow. Belt changed! Thanks so much

You are a God. I last night worked 4 hours last night replacing drum wheels. (Long story) Left belt and deum for the next day. Watched this and 7 minutes later belt and serum back on. Thank you.

Thank you Bill...Excellent instructions .!14 Years..and still helping!

Thank you for such an easy to follow instructional video from a single mom trying to do it all herself!!

I never thought in a million years that I would be replacing a dryer belt, but with your excellent video my husband and I were able to replace it ourselves. Thanks for your clear instructions.

Great instructions! Watched your other video on taking it apart, then this one. Replaced the belt and we are back to drying clothes. Thank you for sharing your knowledge.

This is an excellent video. The demonstration of the pulley tensioning and how to slip it around when you have to do it blind is really key. I'm impressed!

Thank, Bill! I replaced the belt and the idler pulley, today. Couldn't have done it without you!

Just replaced the idler pulley on my Maytag dryer and didn't take proper note of how to put the belt back on. This video helped immensely in getting everything put back together. Thanks for taking the time to make this.

Great video for anyone that has a clue about moving parts. My fiancee and I thank you for putting together a super helpful look at our dryer!

Thank you for your patience and detail in the breakdown. I was just able to repair my belt according to your instructions. Struggled with the front door a little bit, but that was my fault. Thanks again. Keep up the good work

Thank you SOOOO MUCH SIR! I have a Maytag Bravos and I couldn’t find anyone who wasn’t using an access panel…which I don’t have. I can’t thank you enough and it was so easy!

Thanks for posting this video I replaced something 15 years ago and a drum roller today, I don't think I would have gotten the belt back on without your help! I think the dryer was in the house when I bought it 45 years ago and it's still going strong. Two adults and 3 boys, they don't build them like they used to. I guess there aren't a lot of 80-year-old guys that enjoy the challenge of replacing a noisy bearing or two. Again I Thank you.

Bill, thank you so much for this video! It really made a difference. I'm not mechanically inclined, but your video was so easy to follow that I fixed my dryer without needing to hire a repair service. The belt slipped off, and I never would have had the confidence to repair it myself without your video.

So Bill, after watching your video, I was above able to just reach under the drum after it was sitting on the rollers. I pulled the tension roller over as far as it would go and put the belt back on. I couldn't see what I was doing, but could visualize how it went together. Took a few tries, but it saved me some back strain. I really appreciate your guidance.

BILL; outstanding work. I tried it the 1st time; it worked. (With some help from my wife, handing tools over.) LOVE the Classic Big-10 Penn State hat. Great theme. With Coach O'Brian and now Coach Franklin, the TRADITION Continues. Fantastic work on the Tutorial, to change a belt. Saved us $200 ! ! !

Thanks Bill. That was a straight forward explanation of what I have to do to replace my dryer belt and the other parts which are a little stiff.

The video was very helpful and enabled me to replace the belt. Our clothes are drying right now! My wife thinks I'm a hero. :) Thanks a lot.

Thank you very much............I remember replacing a belt about 15 years ago......this videos was a great reminder.....

Thank you Bill. Your instruction to put back the tricky bell is clear and direct to the point. 🙏

You Rock Sir. Thank you for making such a great video. I'm sure you helped many thousands of people like me out in the 8 years you had this posted.

THANKS BILL IM A 65YR OLD WOMEN I FOLLOWED YOUR VIDEO AND IT WAS EASY TO YOU THANKS FOR THIS VIDEO ❤

THANK YOU!!! I may have just found this video in 2019! This is why KZfaq exists. First time home owner and just had that sinking feeling when you think your appliances are dying..then you get rational..and open up KZfaq.. I have the exact same dryer downstairs went to go grab my laundry and after it ran for about an hour it was still rather damp. Not normal at ALL! Wanted to see how much of it I had to take apart in order to get to the lint collector.. (alllllllll the way) Because of your perfect video I now know it's as easy as I hoped!thank you again! Who knows maybe I'll find some lost socks while I'm in there! Operation Dryer begins!!!!!

I usually make a cellphone video as i disassemble things, but didn't do it this time (drat!). One of the drum rollers was bad. I replaced the roller and then couldn't remember the belt routing. I know this belt material won't stretch, so i was baffled as to why i still had about 5 inches of slack with the belt all the way around the drum. This video made it clear. Thanks!

Can't thank you enough! Took me a damn hour to find not only the correct way for the belt path but someone that actually showed it without the drum in! It might seem simple but explaining it without a visual doesn't do much for someone that has never done it before! Thanks Bill!

thank you bill this is gonna help out a lot at work tomorrow! I've never worked on dryers or washers before and thanks to your videos I know exactly what to check for!

simple and clear..thanks Bill. Man, I am so empowered by this video, feel like I can fix anything now!

Bill, thank you for making this video. It really helped me with my dryer. I can help folks out though. It seems impossible at first to do this but I came up with an idea. Simply use painters tape to align the belt to the drum. I placed painters tape on the belt and taped it to the outside of the drum right where it was before it failed (on the rubber wear marks on the drum). This allowed me to insert the drum without moving the belt out of alignment. Once the drum was back in place, I simply did what you instructed and put the belt onto the tensioner and then looped it to the motor. Once this was done, I turned the drum slowly (looking through the crack at the belt to see where the belt and tape were). Once the tape parts of the belt start to get close to the tensioner, you simply reach in and pull them off. One at a time. Made this job VERY easy. Anyway, thanks for the instructions. My dryer works perfectly now. :)

Thank you for the video. I took apart my dryer replacred the belt and pulley, without a repairman. Just the cost of parts. Very helpful

Repairing appliances instead of replacing them is not only cost-effective but also environmentally friendly. By providing guidance on how to replace the belt on Maytag dryer , this video encourages viewers to extend the lifespan of their appliances and reduce waste.

Bill?...You're a hero. I had much of it figured out but that "best way to loop and attach" was missing from my personal data stream. 30 mins open to fix to close to run

Dude, you're the best. I was loosing my mind trying to figure this out.. you just saved my Saturday lol

Wow just changed the belt with the help of this video and it works THANKS TO YOU MY MAN it is very appreciated!❤❤❤❤❤❤❤❤❤❤

Thank you! I couldn't figure out how to wrap the belt around the pulley and tensioner. This shined the light on it...

This video was perfect for me to get the belt back on the dryer. Thank you

Great job explaining the tricky part of putting the belt back into position, which has to be done blind, but showing us in a way that we can see.

Got my dryer from a 2nd hand store, belt busted this morning so im sure it hadn't been changed since it was new. Just ordered this belt, and plan on using it when the belt arrives, thanks a lot!

I want to thank Bill and KZfaq. You guys rock and roll, 🎉🎉🎉😅😅😅baby.

Now that’s how you make an in depth video that doesn’t just assume everyone knows how the belt lines up on the pulley.

Thanks man, I was at a loss on how to get the belt back on after it had jumped off, you saved me!

Dude I thank you so much You saved me so much time and a huge repair bill my cost $20.00 and your 6min video. I love this Country..

Mr. Bill I've been stuck on this for a hour! Thank you for this it solved it in 5 minutes after this 👍 bravo 🤣

Thank you for posting these vids. Momma's dryer is back up and running, at a minimum of expense. Talk about scoring points. I'm a hero now. 8^)

Just watched this to fix my dryer!! Thank you very much. I was standing there like an idiot going why isn't it spinning after I got a new belt.... Thanks for showing me how to loop it around the motor!!

Thank you so much for posting this video. I had to replace the belt and had no clue what to do.

Omg I've been struggling with this for hours. The moron who fixed it before I got it had the belt strung backwards. Holy cow thank you for this.

Thanks man. Even though I wasn’t able to do the “put yourself in the tub and blindly loop the belt” scenario, I was able to figure it out otherwise operating from the right side where my pulleys are.👍🏾

Thanks Bill, this video was very helpful for me. I appreciate your time! Steve in Cleveland

This helped 100% you just saved me $700 to buy a new one thank you very much Bill

Sweet! Thank you for showing how to do the belt to the motor...I got stuck on that part, putting mine back together. Good video!

I never thought that you'd have to take the whole dryer apart just to change a belt. Sounds a bit complicated but from the comments this should help me get it done 💪🏻🤘🏻

Both of your videos have been so helpful man. 🙌 I appreciate you immensely.

This video was SUPER helpful. I'm not at all handy but I was able to understand every step. Thank you so much.

DUDE! I WISH I FOUND THIS VIDEO FIRST! I WASTED SO MUCH TIME DRIVING AROUND BUYING BELTS WHEN ALL ALONG I HAD THE RIGHT SIZED ONE, I WAS JUST INSTALLING IT INCORRECTLY THE WHOLE TIME! I'm mad at myself but so relieved now that it's fixed, so much money wasted at the laundromat man 😔 THANK YOU SO MUCH!

Thanks Bill, It worked perfectly on an old Performa series Maytag with the motor and pulley on the right side as well.

Hey Bill, THANKS for the help - video got me in and out - dryer working fine again. Best wishes to you and those dear to you - keep up the good work!

I had just about given up. because I had knocked of the belt my self. then I was told to check you tube. 5 min later I did test run. then fully assembled and began to dry clothes. excellent video,

Glad this video is still around. It helped greatly. Thank you.

Super helpful. About to start my dryer back up. Wish me luck!

You are a master photographer and instructor, too! Thanks!

This video was very helpful to fix my dryer. My dryer is working great.

Thanks for the instructions. The dryer was squeaking rather loudly so we decided to try to fix it ourselves. We got the dryer apart and then were clueless when it came to putting the belt back on. Now we get to go down and put it back together and hope the noise has gone away.

Bill..thank you so much...glad you put this video up...we have a Maytag legacy which is newer but pretty close...I actually changed the belt my self and thanks to your video was able to blindly replace the belt after the drum was put back in....seems to be running smoothly...thanks again !

Thanks. I have the similar dryer and I'm replacing the rollers and thought I might as well replace the belt. Oh and thank you Maytag for not providing an access panel to get to the belt pulley. No wonder that Maytag guy retired.

Thank-You - Worked perfectly for a Maytag DG-612 - That idler Pulley is a pain!

Thanks for the detailed video on the belt, it saved my ass in the reassembly.

Dude i know this is a very old video but this saved me from having to buy a new dryer! Thank you thank you!

Big help. Was my first time , learned from this video an fixed my dryer. thank you

Thank you. This is a video shown in real life, dirt and all. Looks like you could have used MY DRYER for this. Made it easy to fix my dryer.

Thank you! Helped so much and now I have a working dryer! 👏

Many thanks! You saved me an hour or more of failure and confusion.

Thanks bro. Your video and explanation helped a lot in changing the belt. Really appreciate it.

Thank you! Watched the break down video first and you've really helped me out.

I forgot how the belt was on the pulleys and you helped me out, thanks!

Awesome Video! Once I saw this and especially how to thread the drive band through the tension pully, it was a breeze!

Great video! I like how you showed how the belt goes on without the drum in the way. I was able to nail it the first try.

Thanks for the excellent video Bill. Changed my Maytag Neptune dryer's belt today, and it's working like a champ again. Clear and Concise, keep up the great work.

Awesome video! Thank you SO much. I NEVER could have done this without your help!

Thank you for saving our marriage. We couldn't figure out how to replace the belt around the pully for an Maytag Epic Gas Dryer and were screaming at each other for blaming the other for not looking at the old one before we (HE) pulled it out (lol). We watched other videos, but your explanation and video with the drum *out* saved us from divorce court! We needed to bring out our tiny mouse arms to do it, but thank you for showing it without the drum!!!! You might not think you help people, but YES YOU DO!!!!!! Marriage saved!!!!!!!

This was very helpful to me as I tried to reassemble my Maytag 500 Series dryer. Thank you!

Don't know if your still active on this channel or not, but I had to thank you for this video, my belt had slipped off and I was so confused on the pully system, I could not figure out how get it back on, very easy once you know thanks a million

This video helped A LOT! Thank you for posting!

Thanks so much - the way you show how to put the belt on really helped!!

Thanks. You saved me even more more frustration. wish I would have found this video sooner.