How to remove and reinstall a pool pump motor on a Jandy pool pump Link to the exact motor amzn.to/3x9SZWM I may be compensated for purchases made at this location
Пікірлер: 34
@bassamalshaebani58072 жыл бұрын
I have an old Jandy pump, not as easy as the others to replace, this video saved me a lot of aggravation as I was about to strip the reverse threaded screw. Thank you!
@abypilotАй бұрын
Great video!
@mudrustworkshop9528Ай бұрын
Thanks!
@Mirandaplayswithquaky Жыл бұрын
As answered below, be sure to select the correct voltage on the new motor. If using one breaker its 120, but if you use the double (2) breakers it is 230. Then dont forget your other seals as well baseplate and diffuser seals. But good video.
@semajjsj6 ай бұрын
Thanks for the video! It was extremely helpful today!
@mudrustworkshop95286 ай бұрын
Glad it helped!
@elgenio11ful6 ай бұрын
You saved me $280, thank you!
@mudrustworkshop95286 ай бұрын
Fantastic! Glad it helped!
@alexanderpohoreskey13792 жыл бұрын
Very helpfull. Thank you.
@mudrustworkshop95282 жыл бұрын
You’re welcome!
@williambickley5 жыл бұрын
Well done!
@claudestamey33803 жыл бұрын
huby
@amberkaesbauer33692 жыл бұрын
YEAH
@TheMcmechanic3 жыл бұрын
got mechanical seal spring which way does it go? each side looks different
@tackscall22712 жыл бұрын
Wish he answered that
@tackscall22712 жыл бұрын
Flat plastic side goes against the white
@jamesmcgregor88692 жыл бұрын
Ever had where you've replaced the pump, wired it, restored power to it and it didn't turn on after flipping the switch? Getting power, the pump just isn't turning on.
@mudrustworkshop95282 жыл бұрын
Some new motors have a selectable voltage switch where the motor is wired up. Make sure your correct voltage is selected.
@MrAnibalolego3 жыл бұрын
Can I replace the old one (same one as in the video) with a new variable speed one?
@mudrustworkshop95283 жыл бұрын
Do you mean the old motor with a variable speed? It won’t break anything but depending on the speed that it runs it may make the pump inefficient depending on where it falls on the pump curve
@GenoT323 жыл бұрын
What do you do if there is a leak from the motor where it connects to the housing ?
@mudrustworkshop95283 жыл бұрын
The seal between the pump and motor is going to be the mechanical seal that is around the motor shaft. I would start with inspecting or replacing that.
@MackDaddyVic Жыл бұрын
How do I access the impeller itself? I’m trying to clean it out.
@mudrustworkshop9528 Жыл бұрын
The first 3 mins should get you down to the impeller to where you can do anything needed on it
@brittsipe43592 жыл бұрын
I have replaced the motor exactly as instructed and got an electrician to wire it back up. Whenever I turn it on, it makes a funny clicking noise and does not run. Any ideas?
@mudrustworkshop95282 жыл бұрын
Assuming that the impeller spins freely (it should). Have your electrician verify that the motor is switched to the correct voltage. Many of these motors can be used with 120V or 230V and your application will depend on what voltage you use.
@poolservice3153 Жыл бұрын
It's a diffuser dude
@organicglobe72153 жыл бұрын
What seal did you use?
@mudrustworkshop95283 жыл бұрын
Organic Globe Zodiac R0479400 New Style Ceramic and Carbon Mechanical Shaft Seal Replacement for Select Zodiac Jandy Pool and Spa Pumps www.amazon.com/dp/B006H4C0UQ/ref=cm_sw_r_cp_api_fab_50LGFb9B13B74
@organicglobe72153 жыл бұрын
MudNRust Workshop thanks bud, really helped out.
@mudrustworkshop95283 жыл бұрын
Organic Globe glad I could help!
@orlandotvl2 жыл бұрын
Man so sad Just changed new pump $375 ..soso mad...
@billterri48892 ай бұрын
The seasl manufacturer and suppliers all say never touch the white ceramic portion of the bearing or you will have premature degredation and failure. Skin oils breakdown the costing over time and use. You should be wearing gloves at this part of the process.