How to Replace Front Brakes 07-17 Toyota Camry

Рет қаралды 157,593

1A Auto: Repair Tips & Secrets Only Mechanics Know

Күн бұрын

Buy Now!
New Brake Pad & Rotor Kit from 1AAuto.com 1aau.to/ia/1APBS00028
1A Auto shows you how to repair, install, fix, change or replace your own worn, squeaky, fading old front brakes. This video is applicable to 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17 Toyota Camry
This process should be similar on the following vehicles:
2012 Toyota Camry
2013 Toyota Camry
2014 Toyota Camry
2015 Toyota Camry
2016 Toyota Camry
2017 Toyota Camry
🔧 List of tools used:
• 10mm Wrench 1aau.to/oHQ/1AXAA00010
• 17mm Wrench 1aau.to/oHQ/1AXAA00010
• 14mm Socket 1aau.to/oaTs/1AXAA00015
• 17mm Socket 1aau.to/oaTs/1AXAA00015
• 19mm Socket 1aau.to/oWt/1AXAA00043
• Brake Caliper Hanger 1aau.to/oft/1AXAA00084
• 1/2 Inch Breaker Bar 1aau.to/ooH/1AXAA00078
• Torque Wrench 1aau.to/oaeY/1AXAA00044
• Anti-Seize Grease
• Brake Parts Cleaner
• Copper Anti-Seize
• Floor Jack 1aau.to/oLJ/1AXAA00068
• Hammer 1aau.to/oIu/1AXAA00091
• Jack Stands 1aau.to/oI8/1AXAA00065
• Large C-Clamp
• Wire Brush 1aau.to/oos/1AXAA00079
Subscribe: / @1aauto
Check out our playlist:
Toyota Auto Repair Videos: • Toyota Auto Repair Videos
2011-2017 Toyota Camry 7th Gen: • 2012-2017 Toyota Camry...
For More Info visit us at 1aau.to/h/bx9/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 155

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@RoofedAsian89 4 жыл бұрын

Dont let the brake lines hang , you will damage them

@joewontwice 2 жыл бұрын

If they drop

@imustbecrazy5626 Жыл бұрын

chick's can't car properly.

@pandamobb7614 Жыл бұрын

I didn’t notice until I read comments lol

@AV84USA 4 жыл бұрын

Thumbs down for hanging caliper by brake line at 1:39.

@trini_boi2414 3 жыл бұрын

I was now about say that and if you just changing the pads why take the entire caliper off?🤔

@davidpence9653 3 жыл бұрын

@@trini_boi2414 She resurfaced or replaced rotors.

@hunterholley7708 3 жыл бұрын

I love these videos. They're very informative, concise, and helpful. Would you consider including little tips on how often to replace whatever it is you're doing maintenance on in each video?

@marinersfk7349 4 жыл бұрын

that caliper hangin kills me and im no expert!

@1AAuto 4 жыл бұрын

+MarinersFK7 Thanks for the feedback! We'll pass this info along to our production team.

@topherd1011 3 жыл бұрын

I have pushed the caliper back my entire life without cracking the bleeder. Abs module or not. Especially if I know my fluid is good.

@itspapaj4732 2 жыл бұрын

As long as you take the lid off the reservoir you should be golden lol

@__Dja 2 жыл бұрын

I think it’s a good idea if the car has ABS, just to be safe

@hellomyfriends9740 2 жыл бұрын

Girl you did all this without getting your shirt dirty ✊🏿✊🏿✊🏿 you made it look pretty easy. Thanks.

@1AAuto 2 жыл бұрын

+HelloMyFriends Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@danzemer76 3 ай бұрын

God bless this lady

@johnrinck4883 2 жыл бұрын

I needed the help of a breaker bar to take the 17mm bolts off the mounting bracket. Didn't take much effort with the breaker bar, but I couldn't budge it with a regular wrench. Also, when removing the 14mm caliper bolts, I had a problem with my 17mm crescent wrench being too wide, so I had to go buy a thinner one. I've never had an issue with a crescent wrench being too wide, but I did here. Great video, by the way! Helped me a ton!

@mallorygutierrez9243 5 ай бұрын

I'm having a hard time sliding the inner brake pad into the clips and when I finally did I forgot to put in the butterfly wire spring and it popped out 😂😂😂

@timcochran5807 Жыл бұрын

Great instructional video!! I have brake rotors and pads for the front of our 2014 Toyota Camry, which I purchased from 1A Auto. First class parts and instructional videos as always. Will be replacing in the next few days.

@tonyhall3148 Жыл бұрын

Excellent Video! Thank you!

@M4STERcontrol 4 жыл бұрын

Thanks for posting this. This is a huge help.

@1AAuto 4 жыл бұрын

+Anim8tor Thanks for checking us out! 1AAuto.com

@ms8367 4 жыл бұрын

Fantastic video! Thanks for putting out quality content. Will definitely buy from you guys.

@PTLB772 Жыл бұрын

Nice, letting the brake line hose just hang with all that weight, glad you did end up putting it on the hanger to keep from damaging the brake line hose!

@charleshogan Ай бұрын

Thanks for sharing your videos with us you dine a great job on the install i believe it Will give me thr confidence i need to fix my breaks in my Camry i did it once and its started sqeeking I used the cheapest part's available at that time but im trying to get some good quality stuff for it this time around im change the rotors to

@AMIAmigaman Жыл бұрын

One of the better videos. She knows what she's doing.

@daleperez1264 2 жыл бұрын

Thank you for the video

@stevekovach1117 2 жыл бұрын

nice job, good video. thank you

@jumaljuma 2 жыл бұрын

Great job 👏

@Buuttcc 4 жыл бұрын

Very detailed video. You should make more.

@mogtrader8 3 жыл бұрын

Should the indicator clips always be on the top part of the pads? Thank you for the videos. You guys rock.

@edbo10 3 жыл бұрын

i dunno if they've changed things for newer models, but I know the 3rd and 4th gen camrys both have the factory manual stating to put the wear indicators on the top side of the inner pad

@scottkim8659 2 жыл бұрын

Thanks for the super helpful video! Btw, what size (in mm) combination wrench fits the bleeder screw?

@michaelp8053 2 жыл бұрын

8mm

@martinherrera9606 Жыл бұрын

Thank You!

@heatherboyer651 3 жыл бұрын

did my brakes thank u so much

@1AAuto 3 жыл бұрын

+Heather Boyer Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

@scottmattson4765 3 жыл бұрын

Very excellent video

@1AAuto 3 жыл бұрын

+Scott Mattson Thanks for the feedback!

@sheddski2942 Жыл бұрын

are camry hybrid brakes replacing the same way? or because of them being regeneration they need diferent procedure ?

@pkaranja3541 4 жыл бұрын

Good video. Make more.

@1AAuto 4 жыл бұрын

+P K Thank you for your feedback! We are always creating more videos. In the meantime you can check out more at our video library.

@thestonehousefarm1942 2 ай бұрын

Do the rotors not have a set screw? Good videos

@muhammadsaad7638 4 жыл бұрын

Those are good brake pad. EBC red stuff are amazing pads also very expensive

@1AAuto 4 жыл бұрын

+Muhammad Saad Thanks for checking us out! 1AAuto.com

@Sammydx1 4 жыл бұрын

I was going to say .... EBC pads are high quality ?

@abbas1872 3 жыл бұрын

I think 1A auto have been watch South Main Auto videos, one of them has learnt how to clean and lube a caliper bracket properly.

@guillermovillalonabryan2533 4 жыл бұрын

I have and appointment next week to do my front brakes on my 2011 toyota camry 328 Dallas after seeing this video i will try to do it my self I don’t care if f up lol seeing to be pretty easy

@1AAuto 4 жыл бұрын

+Guillermo Villalona Bryan Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

@Mr420FourTwenty420 Жыл бұрын

Ive ruined the break booster on a 2015 pilot and a 2013 acadia by pushing the brake fluid back in , and i did take the brake fluid cap off, good to see someone do it the correct way new vehicles can be sensitive. Also had to replace front and rear pads and rotors on my 13 camry got it 2 years ago pads look brand new they say toyota and advics on the brake pads cant say i recommend going oem when replacing the rotors and pads. Never seen such a deep groove in the pad and rotor.

@alibaba66able 4 жыл бұрын

A question for you: I have a 2019 Camry XSE. IS there anything electronically I have to do when changing the pads? Someone said that a guy changed the brake pads and the car didn't start after that!!! Just wondering. Thanks

@1AAuto 4 жыл бұрын

+alibaba66able Hello, this video only covers through the 2017 model year, we do not as of yet have a video that covers 2019, so we are not able to answer your question definitively. Please contact your dealer for more assistance.

@tonyhahahaha6590 Жыл бұрын

Should you index the rotors with a dial indicator?

@craigvergy 3 жыл бұрын

Hi there, great video. I have a 2020 Toyota Camry XSE V6. Would you be able to advise of the torque settings for the bracket and caliper bolts? Also, do you have any idea where I can purchase and/or download the workshop manual for a 2020 Camry! Thank you. Craig.

@1AAuto 3 жыл бұрын

+Craig Vergelius Thanks for checking us out! We currently wouldn't have that information but you should be able to get assistance with this from your local dealership! 1aauto.com

@itspapaj4732 2 жыл бұрын

~75 ft/lbs for front caliper bracket, and ~25ft/lbs for the slide pins

@HaloGTMaster94 3 жыл бұрын

Good Video!!!!

@1AAuto 3 жыл бұрын

+champagneedward Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@Tony53030 2 жыл бұрын

Thanks. For best. How was your the who you how ermecny brakes

@sailingpittsburgh 3 жыл бұрын

Other people have asked about the bleeder being open to press the piston in. What kind of damage can be done to the anti lock brakes if you do not open the bleeder valve? I have never done this when changing brakes and have not had any problems. Is this specific to Toyotas?

@thetexaschainsaw9366 3 жыл бұрын

Same here i never open the bleeder when compressing the piston but its good to do so to keep dirty brake fluid from going back into brake reservoir its just preference.

@andresnarvaez9667 Жыл бұрын

So is ok not to bleed the caliper just when I change pads , I tried to open the bleeder screw but is hard to turn it

@NWCI 4 жыл бұрын

Went straight to comment section after seeing caliper hanging, not disappointed 😂. Anyway it's too light of a caliper to do any damage.

@eshanaa 3 жыл бұрын

Hey guys I just replaced front rotors of my Camry what I noticed there is one spring from the brake pads was missing would there be any trouble if there is only one spring instead two. Thanks

@-burak.k-2029 3 жыл бұрын

If it is the spring that separates the two brake pads yes and no... All it does is keep random vibrations from happening but you can goo without them too

@jakeh3144 Жыл бұрын

Are you really supposed to open the bleeders to compress the caliper? I've always been told not to unless you plan to rebleed the system.

@isaaccongats 2 жыл бұрын

I just purchased same racing rotors and sticker on them says "front passenger side" and slots directed to wrong direction. Where slots supposed to be directed?

@tearsofjoy1625 2 жыл бұрын

The slide pin with the rubber bushing goes in the bottom hole on 2010 camrys.

@metallampman 4 жыл бұрын

how important is it to open the bleeder nut,, will it damage the anti loc system if i just push the piston back in with a c clamp to allow for new pads without doing that ?

@1AAuto 4 жыл бұрын

+Arch Stanton Thanks for watching! You want to have the bleeder screw open if you are pressing the piston back in.

@sailingpittsburgh 3 жыл бұрын

@@1AAuto Why?

@DavidGomez-mh2op 3 жыл бұрын

@@1AAuto but what can happen to the ABS if the bleeder screw isn't opened and the cap on the brake reservoir was taken off instead to compress the calipers?

@Mm01233 10 ай бұрын

What brand of caliper grease I can use for pins

@BurtBowers 2 жыл бұрын

I generally never open bleeder valve only when I need to bleed the brakes, opening the wheel bleeder valves will let air into the system I only pop the master cylinder cap when doing brakes & add fluid if needed.

@phillychuck 4 жыл бұрын

Nothing in stock for Camry on your website

@tommason5689 2 ай бұрын

I did this job on 2007 Lexus ES350 which is same as Camry. I am not sure why but I could not install the pads with the indicator clip on. The indicator clip is way too strong and refuses to get into the slot no matter what. I tried many times and finally had to give up and installed the pads without them.

@khizar196 4 жыл бұрын

Liked it.

@1AAuto 4 жыл бұрын

+Khizar Shah Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@emmvee1678 2 жыл бұрын

Those little anti rattle springs I found 2 in the driveway after doing them.

@1AAuto 2 жыл бұрын

+emvee16 Thanks for the feedback!

@hmoobdude5111 2 жыл бұрын

Why not use the two screw holes on the rotor to remove the stuck rotor? What if someone wanted to use their old rotors? I can't believe no video on youtube explains this obvious feature.

@alfredbernal8603 Жыл бұрын

I bet you Sylvia can beat me at an arm wrestle! 💪

@jams1533 9 ай бұрын

How “necessary” are those indicator clips

@TokersDomain 4 ай бұрын

She should have her own channel

@andrewcole9605 5 жыл бұрын

It's 5 to 2 I didn't see use bungee cord... Plus you should use blue loc T

@kismofer1 4 жыл бұрын

she's good....thanks for sharing this video!!

@1AAuto 4 жыл бұрын

+Fernando Gausin Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto

@brielrivera2743 4 ай бұрын

I did exactly what you did and funny thing is my car has the same type of rotors , and it keeps making this grinding noise and it’s sucks , here did the whole thing and nothing , any help ?

@1AAuto 4 ай бұрын

+@brielrivera2743 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@magnaviator 10 ай бұрын

I thought the lug nuts on camries were 21mm? Is it 21 or 19mm?

@3NZ0S 4 жыл бұрын

Why not just remove the brake cap instead of opening the bleeder valve it just causes more work.

@1AAuto 4 жыл бұрын

+Jacob Pena We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair.

@likedat2 4 жыл бұрын

Which way is the slotted rotors supposed to face

@1AAuto 4 жыл бұрын

+Ciggy Pop Culture For rotors with slots machined in the same direction as the internal cooling vanes, the slots should lean toward the back of the car. For rotors with slots machined in the opposite direction as the internal cooling vanes, the slots should lean toward the front of the car.

@diegovillarreal2037 2 жыл бұрын

Do I need to open the bleeder screw if Im only changing the brake pads and not the rotors?

@__Dja 2 жыл бұрын

I almost always bleed the brakes anytime I do a brake job out of habit but in reality you could just open the cap on the brake fluid reservoir and be okay

@BeyondAverageSkilled 2 жыл бұрын

took me 8 hours to finished one brake replacement and i did a really poor job...gotta go back and check it tomorrow.

@reikisponge 2 жыл бұрын

Anything you found different or learned doing it? How did it turn out?

@BoringAaron 3 жыл бұрын

What's the purpose of the holes in the new rotor?

@1AAuto 3 жыл бұрын

+sleepspace Crossed drilled rotors and slotted rotors (and rotors that are both slotted and drilled) are designed to allow gases to escape that build up between the brake pad and brake rotor. This allows your brakes to run cooler and stop better. sited on redline360

@cesarvargas31 2 жыл бұрын

Anyone else get a high pitch squeal when you installed this set? Followed all directions and even followed the other video on "which direction to install Slotted/drilled rotors" Thoughts?

@isaaccongats 2 жыл бұрын

I have the same question. I think slots supposed to look different direction. Other videos confirm that. I think she put them on wrong side.

@MARTINA-gc3tq 3 жыл бұрын

shouldn't the wear noise indicator be fitted on the piston side?

@itspapaj4732 2 жыл бұрын

Yes, per Toyota's manual, state to put the indicator on the top of the inner pad

@JEDIJackCurenton Жыл бұрын

did she just hang the caliper by the brake line???

@rigweldernomad932 4 жыл бұрын

Bleeding it like that doesn't that let air into the lines?

@alexandergreene1728 4 жыл бұрын

It is gravity bleeding; The aster cylinder is at a higher point than the piston, so the brake fluid will flow downward. You can actually DIY bleed the entire system this way, as most every car the master cylinder/reservoir are at a higher point than the pistons at the calipers. The system isn't under a vacuum either, so there is no way for it to "suck" air into the system.

@davidpence9653 3 жыл бұрын

Where does the air flow into the line? It may be a myth.

@johncarter5772 2 жыл бұрын

iI found it easier to compress the calipers before you remove them

@heatherboyer651 3 жыл бұрын

how do u know which direction those rotors go . cant find it

@1AAuto 3 жыл бұрын

+Heather Boyer There is an image on our website if you pull up part number 1APBS00028. Rotors with a directional vane design need to be installed with the vanes sweeping back towards the rear of the car (unless specified other wise by the vehicle's manufacturer).

@tomgorman1594 2 жыл бұрын

Shouldn't you apply grease to the break pad ears, and the top surface of the new mounting tabs as well?

@1AAuto 2 жыл бұрын

+Tom Gorman Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@c.h.r.i.s2253 2 жыл бұрын

Every single video for the front brakes has the small clips/wear indicators on different. Some specifically on the top on the outer and bottom on the inner, some both on top. I thought it was top on outer a d bottom on inner

@itspapaj4732 2 жыл бұрын

Toyota states in their manuals that it has to be on the top of the inner pad

@alfredbernal8603 Жыл бұрын

@1:03-1:06, snap on wrench says" OUCH! WHAT THE HECK!"

@Sole650 8 ай бұрын

Toyota dealership and auto shops is punching the air right now lol thank you

@1AAuto 8 ай бұрын

+UceRaven Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@alexandercrush 4 жыл бұрын

I thought this video was replacing brake pads and was shocked how much was needed to be done and then realized the title said replace front brakes lol

@globaleffect1969 4 жыл бұрын

This is a good video of the whole process, Watch my video kzfaq.info/get/bejne/gKt7nrVyyae2o4k.html if you just want to see how to change the brake pads right quick.

@jaywhite3085 3 жыл бұрын

This works for a 2020 also correct?

@1AAuto 3 жыл бұрын

+Jalen White This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c

@waqarqadeer5217 2 жыл бұрын

Did you just let the brake line dangling on in the beginning 🤔

@journeyquest1 2 жыл бұрын

Dude!!!

@DanTheManIOM 4 жыл бұрын

do you need the brake pad inidcator at (10:10) ?

@thetexaschainsaw9366 4 жыл бұрын

Yes because thats what lets you know your brake pads are getting worn down. But you don't have to

@hearse2us 3 жыл бұрын

No, but if you don't install it, you'll have no warning before the pad material completely wears down and then you'll have metal against metal. that's dangerous and could cause a lot of damage to all the components if that happens. But all it does is make it squeal so you know its getting close.

@blesdavis7637 2 жыл бұрын

Thanks Sue. u save me $170.

@brianwatt558 3 жыл бұрын

I thought u was changing brakes you changing brakes and rotors ?

@1AAuto 3 жыл бұрын

+Brian Watt Yes, the brake pads and rotors are being changed out.

@master6435 3 жыл бұрын

for the warranty for the old rotors do they have to be sent back

@1AAuto 3 жыл бұрын

+Master Yes, per our warranty, the defective parts need to be returned after replacements are received. Once we receive the defective parts, the warranty transfers onto the new replacement parts.

@richardmanus1635 3 жыл бұрын

NEVER HANG THECALIPER BY BRAKE HOSE

@1AAuto 3 жыл бұрын

+Richard Manus Thanks for the tip!

@Mclovinxxx23 4 жыл бұрын

I'm no mechanic but why in the world did she looses up the bleeder valve to change brakes? Ive never done that Nd ive changed hundred of brake pads!?

@1AAuto 4 жыл бұрын

+Mclovinxxx23 Thanks for checking us out! It is always smart to bleed the brakes when doing any kind of work on them to ensure that no air entered the system as this can affect the performance of your braking. 1aauto.com

@vangshooter7723 Жыл бұрын

How you just going to let the caliper hang like that at 1:45

@garymijangos9403 Жыл бұрын

Why did she let the brake caliper hang you can damage the line that way

@deanhenthorn1890 11 ай бұрын

Nobody who’s actually a mechanic will open the brake line which can potentially cause air to enter the system. Don’t do that. Never let the caliper hang from the rubber hose, support the weight by hanging it. Obviously this lady only represents why my wife doesn’t work on my cars and trucks. 1A Auto needs a better instructor!

@elwhastrummer 2 ай бұрын

Yikes you let the rear calipers hang by the hose on a different video.

@static_Tricolor_camry 5 ай бұрын

That is so bad for the brake line, leaving it hanging without a Bunge cord holding it.

@MrCchh7 4 жыл бұрын

Great vid but she let the caliper hang😩😩 well at least she did it gently I guess and didn’t just drop it

@one7decimal2eight 2 жыл бұрын

Why would they put the red pads on? If I remember correctly the green pads are for the street and the red ones are more for racing which means they take longer to work properly. You need heat behind them for optimal braking. I heard many horror stories from my racing days of people putting red ones on street cars and not having crap for braking. No wonder this person had new pads put in. I would have just slapped new OEM pads onto those rotors and rolled with that. Unless the rotors are warped or too worn there is no need to do pads and rotors if the pads are worn.

@MOEZANDERS Жыл бұрын

Never get brake products from A1 Auto I ordered brake pads and rotors from A1 Auto for my 2015 Toyota Camry my vehicle started to ride like absolute garbage the brakes were grabbing and have never stopped until I bought a new pair from AutoZone yes I said it I I've been shaking changing brakes for decades now and these are the worst breaks I have ever dealt with

@phantomshtter Жыл бұрын

...aaaaand no torque spec for the bracket to the hub.😑

@standardarm63 Жыл бұрын

You left out my least favorite part of life . Reusing wheel studs.

@Passions Жыл бұрын

WTF dangling brake line!!! COME ON

@Mohammed-vs4fm 10 ай бұрын

You should never hang the caliber like that. WOMEN 😂😂😂😂😂

@davidowen6103 5 жыл бұрын

Haha drilled and slotted rotors on a Toyota Camry.

@1AAuto 5 жыл бұрын

Thanks for checking us out! +David Owen

@shawnm4785 4 жыл бұрын

that car has nearly 300 hp so yea makes sense

@steveparavola6858 4 жыл бұрын

I've owned a Camry with the 268 HP and 6 speed transmission for 2 years. This thing is faster than my 1969 Mach 1 Mustang with the V8 rated at 300+ HP! Just sayin...

@codotnunia596 3 жыл бұрын

I'm confused as to why this is funny to you. Drilled and slotted Rotors improve braking performance period, on any car.... The whole point is to lower the amount of space it takes to slow down to zero.

@deennrap 3 жыл бұрын

@@codotnunia596 people are funny...im accomplishing the same if not more things with my Camry thn i was doing with audi. all cars are cars and they take you places.