No video
How to use / setup a long handled threaded rivet tool
Рет қаралды 131,760
Күн бұрынThis is an instructional video on how to use the Princess Auto 8534224 17" long handled threaded rivet tool. I recently purchased this tool online. When I received it there where no instructions on how to change the various dies and how to use this tool. Both the supplier and the manufacturer of the tool could not provide one. I have used cheaper hand thread insert tools only to break them after setting a half dozen or so 1/4" aluminum inserts. The tool in the video is much better made and will set steel threaded inserts. After taking a bit of time to figure out mainly how to change the dies, I decided that a short video would be useful to others, even using tools from other suppliers. I have been using threaded inserts on my 1929 Ford roadster hot rod and recently on the cowling for the electric fan for the radiator. This will be another video at a later date.
Subscribe to my KZfaq channel at / 1929fordhotrod
Please visit my website at 1929fordhotrod.com for more great hot rod build ideas.
Like me on Facebook at / 146153025450971
Follow me on Twitter at / 1929fordhotrod
Subscribe to my RSS feed at feeds.feedburne...
@MarioErnestoTrevino 3 жыл бұрын
The only guy on KZfaq who shows how to change the dies. Thanks, unfortunately my rivet tool is different.
@Ranger42 7 жыл бұрын
This is an outstanding instructional video. Best on KZfaq in regards to these tools. Just purchased an Astro 1442, which is similar to yours, on Amazon and this training will make things easier. Thank you Sir.
@robertrenshaw7527 6 жыл бұрын
Thanks. Just received a similar item from amazon and couldn't work out how to change the mandrel. Your video showed me the pull back collar that I didn't realize was a pull back collar. I received instructions with mine but I don't think they explain this bit clearly enough. So glad I found your video before I ended up stripping the end down to work it out myself.
@wrdennig 5 жыл бұрын
Thank you for that no-nonsense how-to video. I have an older system where you use two wrenches to set the inserts. Very difficult and hard to control. Now I'm going to get one of these.
@Dukeandmandy 4 жыл бұрын
Thank you. Bought one on amazon and they had no how to video or directions. Yours was great.
@mattbeazer5896 6 жыл бұрын
Mine is a different brand but the same tool... it came with instructions but they were so terrible I couldn't figure out how to get the die out even with the horrible Chinese-English translated instructions. I had the damn thing locked in a vice trying to turn the stupid insert out! Thank you so much for sharing this, I figured it had to be easy and made difficult by terrible instructions.
@jimmydykes635 5 жыл бұрын
Thank you Sir. I just bought a tool similar to yours also No instructions. You saved me a lot of aggravation
@Ottonic6 4 жыл бұрын
On mine to release from the set insert instead of pumping the handles in and out to unscrew it from the finished insertion, I just turn the wheel at the end of the center insertion rod counterclockwise and that's it. Either way seems simple enough. Great video. Thank you!
@osos231 6 жыл бұрын
Great video, thanks so much. Just bought the same style rivet tool and for the life of me I couldn't figure out how to change the die.
@leecastrejon6151 7 жыл бұрын
I am sure glad you are just some person who just did this for humanity and were not reading off of some paper like a commentator
@1929fordhotrod 7 жыл бұрын
Thank you. When I first bought this tool there were no instructions on how to use it and when I received them they were a joke. This resulted in the video only to help others out.
@billgegg6037 4 жыл бұрын
My Rexbeti also did not come with instructions. Thank you for your explanation and demo.
@GearheadOutlaw 9 жыл бұрын
Great tool. Thanks for reviewing and sharing.
@5abivt 3 жыл бұрын
Great video. BUT.. it shows how to change the mandrel. Does not explain a critical part of installation which is setting the depth and knowing the thickness of the panel being used to properly set the riv nut.
@facundozarate5030 5 жыл бұрын
What is the scale with a yellow background and black lines?
@dalevalley221 5 жыл бұрын
Nice video! Was pulling my hair out, one from amazon had poor instructions, didnt realize was a springloaded peice needing pushed back to undo rest of the die.
@sandralloyd838 4 жыл бұрын
Excellent video. Thank you
@alzaabialzaabi 7 жыл бұрын
So happy to watch this, i have one same as yours models BT-604
@mbk1251 5 жыл бұрын
Very informative made plain easy to understand thank you very much.
@GenericUserUnknown 4 жыл бұрын
Thank you for doing this video.
@Crusty_Camper 5 жыл бұрын
Excellent, thank you. There were no instructions with mine either.
@BennyMack 5 жыл бұрын
Thanks for your helpful service.
@alnfong1228 5 жыл бұрын
Wow..Thank you so much for the video!! It sure did help me out! Thanks again!!
@dragstriprabies2.059 4 жыл бұрын
Great video
@31186dan 5 жыл бұрын
Thank you , very helpful video
@gregwittler7868 4 жыл бұрын
Thank you, as with you mine came with no instructions either, although UNLIKE you I have never used a threaded insert tool before.
@borthewolf3376 7 жыл бұрын
How did you set the stroke length? It differs depending on the nut size used and the thickness of the panel. If the stroke is not set properly either the mandrel will break or the nut doesn't sufficiently bite in to the panel.
@janlazurko5060 Жыл бұрын
The stroke length is the most important aspect in my opinion. Another 8-minutes wasted
@Dronerangerspro 5 жыл бұрын
Great demo, thank you 🙏
@patbradley916 3 жыл бұрын
Thank you
@DJDEEM1 8 жыл бұрын
Thanks. This was a helpful video.
@neudimensions1320 6 жыл бұрын
I almost skipped this video due to the crappy robotic voice intro.
@jeremiahjohnson731 5 жыл бұрын
Team Neudimensions me to. 😊
@31186dan 5 жыл бұрын
Same!
@CHB_98 Жыл бұрын
How do you adjust the scale in the middle of the tool. My instructions says it should be at 0 and 6 mm but it’s currently sitting at 9 mm when arms are fully extended
@jspriver 5 жыл бұрын
Thanks
@GnosisMan50 7 жыл бұрын
wait!..how did the the insert tool come off at the end of the video!? The die was threaded and the only way out would be by rotating the tool. It looks like a magical trick that was done there.
@1929fordhotrod 7 жыл бұрын
No magic, once the insert has been set, just open and closed to handles of the insert tool and it will un-thread itself from the set insert.
@3rd_Millennium_Engineering 5 ай бұрын
At 8:00, you show how to easily remove the tool by opening the 2 handles; unless you have a different style that I don't know about, that technique does not work. Instead, you must rotate the know counter-clockwise to remove the die and tool from the installed rivnut.
@NathanNostaw 7 жыл бұрын
Cheers, seems like an ok tool.
@llynellyn 6 жыл бұрын
Thank you.
@adadhao1016 4 жыл бұрын
Still using such a laborious tool? Sigma rivet nut adapter makes it easy to set the rivet nut! It's time to have a more relaxed tool.
@tomh9322 2 жыл бұрын
Great instruction but what about the 10mm gage?
@hollyhatcherparashar 4 жыл бұрын
This video is slower than CHRISTMAS!!
@c0mputer 6 жыл бұрын
Ahhh, that little collar is spring loaded to be able to unthread the die. Exactly what I needed to know. Like a foreskin.
@craigaherrington 5 жыл бұрын
😂😂
@mccwho 2 жыл бұрын
What's the measurement scale for?
@elrroco1 9 жыл бұрын
Exellent video, thank you so much. Very helpfull.Could you please tell me where can I buy this tool? I need it asap. Thank you again.
@1929fordhotrod 9 жыл бұрын
elrroco1 I bought this tool in Canada from Princess Auto. Habour Freight should have a similar one.
@elrroco1 9 жыл бұрын
***** thank you so much again.
@ve3xtr 7 жыл бұрын
princess auto doesn't sell this tool any more. had to get one off amazon.ca
@frankbarbara2507 5 жыл бұрын
THE HOLE IN THE WASHER SHOULD HAVE BEEN A CLOSER FIT FOR THE RIVNUT...!!!
@martinglynn8774 4 жыл бұрын
Thank you for going to the trouble of informing us how to use this tool it has saved me a lot of time.
@-_o_o_- 5 жыл бұрын
Is it well to M12 stainless steel nuts?
@1929fordhotrod 5 жыл бұрын
Not sure. I have not tried it but suspect it would be fine.
@pollyaloy 6 жыл бұрын
Thanks
Larry Sbrusch
Рет қаралды 202 М.