Thanks for helping me get my Hurricane-Katrina-era McCulloch chainsaw up and running after all the lines disintegrated. I was hesitant to split the case but your video was a tremendous help! Thank you!

Thank you for this video, I have the exact same chainsaw. Your explanation on carburetor and gas lines was extremely helpful.

Your vids give me confidence to repair myself. Appreciate you sharing.

Great video, showed exactly what needed to be done to change the fuel lines. Thanks for posting this!

Thank you for sharing this. I am just a wanna be fixer guy....and I loved this chainsaw....it has been sitting for too many years and your video demonstrated how simple everything was....AND paying attention to details helped too. Looking for many more helpful hints from your site

Very helpful video, I found one chainsaw in the rubbish. Barely used but won't start. Fit a spark plug that was missing and make it run with fuel in the carb, but couldn't figure out the fuel lines. Now with this video will be very easy to put it back together

THAT WAS SPOT ON AND VERY DETAILED, THANKS FOR POSTING

Great video and precisely what I needed to know for the specific model of chainsaw that I have. The message at the end gave me a lot of courage and I think I may undertake this whole procedure on my saw, which needs it, wish me luck.

Same chainsaw as mine, i looked for a video as my fuel lines had cracked - Thanks this video saved me alot of messing about.

I'm working on one as we speak , this video is going to make it so much easier . Thank you so much 💯 appreciate it.

I have a chainsaw that needs the fuel lines replaced. This is a good refresher since I haven't worked on one in a few years. Looking forward to the video on the carburetor.

A+ Alot of hard work goes into what you have done so far, look forward to the conclusion.

I just want to thank you for this video that has been so helpful to me. I just got one mcculock and am going to replace the gas lines. It will be now much easier to do. Thanks again.

Fantastic! Just what I needed to get the fuel lines installed!

Great video, looking forward to part two. Keep up the good work 👍🏻

Trying to fix my chainsaw that I have not used in years. Thanks for the video!

what an excellent detailed description in simple laymans terminology well done from sunny australia!!

I can't believe I found this. I have this exact model chain saw and it would not run. After investigation I found that the fuel lines were bad, just like in the video. It has every detail I need to fix mine. Thanks for doing this. Now I just hope I can find the parts.

Did this exact repair on a MacCat saw I got from a yard sale that is almost identical. I wish this video had been available then as it would have made the job much easier. I had the additional problem of the cork gasket for the oiler cap rotting and spilling debris into the bar oil which was the pulled into the oiler by a broken line that separated from the filter. Took quite a bit more disassembly to clean out all the oil journals. Wonderful saw tho, I’ve used it to clean up after 2 hurricanes and a tornado and it cuts like a beast despite being 20+ yrs old.

Excellent. Thank you.

Thanks so much! This is exactly what I needed to fix my McCulloch Eager Beaver 2014. (I think it's the same saw.

Another great repair job done. Cheers 🦘🇦🇺

Great job! Yes I have replaced fuel lines on my old home lite which is a pain to do too. 😂

Great video. It will help me to repair my Silver Eagle 2000 series. Thank you!

I would have a go now myself having seen how you did it, but boy what a lot of work to replace the fuel lines .

Great video, thanks

That's the right way got one same as that one great chain saw and video thanks

Thanks I will try tomorrow. Thanks for sharing

yeah, i'd definitely have fixed an old Mac chainsaw for sure. but, MY GOODNESS that looks like it was SO tedious to do!! lol I have huge hands, and fat fingers, and i'd have definitely had trouble fishing the fuel line up to the tank. Great video man, i love your content, thank you!

Good on point video. Thanks

Thanks for this video it helps me a lot to fix my chainsaw :)

Excellent video.

Dang. Good job. You did a good job cleaning. Same with your last poulan blower video. That piston and ring was shiny

I worked on one of these for my uncle just a few weeks ago. I was able to change the fuel lines without splitting it, but it wasn’t easy. This isn’t the first McCulloch like that that I’ve worked on though, I did split the case on the previous one, so I was seeing if there was an easier way lol

Just bought a goped for $75. Had to do this and epoxy the intake together. Today I'll be replacing the clutch and it should run like new!

Great job

Great video! Great find!!!!!

I bet your pretty happy to have one of these working saws

I change fuel lines all the time. Running the system dry is what I do also and I have never had a problem .

I agree with you in purging all fuel from the fuel lines and carburetor will help keep the components in good shape, i personally drain all fuel from all my equipment if i know they will be stored for more than a couple of days and it really helps to preserve all the soft parts, i also believe prolonged fuel exposure causes a lot of damage And as for the comments that purging the fuel will dry out the diphragms i really disagree, if that was true i guess all the diphragms would be already bad from the packaging

great video - going to help me get my free chainsaw running (hopefully!)

I am retired and started up a small engine service and found that one of my best tools is my cell phone. I take pictures of fuel lines, carb. linkage, etc. It saves alot of fustration especially if your old like myself and your memory isn't that great. P.S. I really enjoy watching your videos they are a great help and you have some good tips/advice.

Not bad! You got most of it right. I work on chainsaws almost every day, And yes! I do have a pile of these and mini mac saws.First off, if you don't have 90 PSI for your minimum numbers for your compression check you won't get a 2-stroke to idle when warmed up! Second thing, It's not the ethanol that destroys the fuel lines and diaphragm, But the Benzene in pump fuel does a job on rubber Ethanol will crode aluminum and also is the culprit for all the water in your fuel system! It has an extra molecule of water that makes alcohol and draws moisture to it. I would disagree that the ring was worn due to lack of oil! If there is ever a lack of oil It's because there was none mixed in with gas and always bakes the piston! Men have a tendency to put just a little more than the recommended amount because he is worried about seizing the piston! Unaware that is usually the reason the piston is all scraped up at exaust port. And a majority of the over heating problems when you got a puddle of it in the exaust pipe! 50/1 2.6 once in a gallon of premium fuel or better! I use VP small engine fuel already pre mixed. Regular gasoline is garbage these days! And the hotter it gets the worse it pre detonates and will destroy a 2-stroke engine. Here is what I see most often that stops a chainsaw from running. You have to keep the chain sharp on a chainsaw! Otherwise it makes a powder enstead of chips or if you're really good at sharpening you make shavings! It sucks it into the holes in the flywheel side and mixed with the thick bar oil sold to you, It makes a goohy mess and slings it across the face of the coil and that's the end of your sparky,Sparky!😉

Just got a free "brand new" still in the box, never used Mac 3216. This video is so helpful because, of course, the bulb and fuel lines had dried and cracked.

Yay! I've been waiting for this.

Thank you for making this, I'm not looking forward to what you did that I'm about to do but it's not worth selling, I know it runs but yeah primer bulb is shot and I'm assuming it needs fuel lines as well. Yay here we go

nice film, greetings from germany

mac tech here. You will find these clam shell models for free or cheap alot. You can rig after market parts to work but we refuse them. The labor and part rate is far more than the saw is worth so people throw them away.

Great video. I am definitely not doing this myself.

Have a Homelite string line trimmer that my kid brought home along with two other mowers found at the curb. The mowers seem to work okay, although one needs a new throttle cable.. The string trimmer had fuel in... And I smelled it. Straight gassed.. showed my kid what happens to the piston when straight gassed, and he saw the scoring. Well, now I seem to have some extra parts... Even a dead one has some use.

I would try it

I bought the green 3/32 line and that was tight as can be to pull through will I have any leaking issues/ lack of fuel? It does idle great but having problems with higher revs. I didn’t tear into the carb yet but I’m guessing I need a carb kit.

Love these old mac saws I have a super old one I need to repair that be fun #repairgang

It all depends, Donyboy73 (Don Desjardins) says mower shops would charge 1 hours labour in Canada to repair it which costs $100-$120 CAD so I would do it myself since I have the abilities & patience to do it. He was explaining how a chainsaw which had a tree fall on it wasn't worth repairing because the plastic parts broke on it despite the engine,oil & fuel tanks,etc were still alright om it,the cost of parts & labour was only $100 CAD less than buying a brand new chainsaw !

I don’t use mcculloch saws however I do like them. I use a stihl ms250 and that’s not too bad to redo the lines. I guess if I had to do the lines I would but I prefer not to

Old mccoulghs are great

Dontou recall if the 3/16th is the inside diameter or the outside? Just aquired this chainsaw and these videos are incredible!

same

i have just been given one of thies 🤣how random thanks for vid

Do you have any confidence with fuel stabilizers?

What Carburetor Model and Number did you use for the saw

What size did you use for the fuel and oiler lines?

I have a mac 3200 and the piston goes up and down put seems to hit something and stop at the top I enspected the piston not scored so I attempted to take off the bolt on starter side but It made a full up down as it broke threw what ever was stopping it the bolt didn't come off I that kept spinning it and it became easier and easier to turn after time , I got it started it ran for a few min but now all lines fuel ect are cracked any idea why it may have been so hard to make full rotation or what it may have been hitting, thanks

Hey was there a bar spacer (gas tank side of the bar) with your saw? And how long was your bar? Thx

Good job brother the only problem is you need small hands to do this repair.. I would of lost my rag with it without the first 10 mins lol

Ok I took out the plug, left it connected and check for spark, got nothing...that explains why it won't start. It was a cheap plug that came in a kit. Tried an old AC Delco plug for a car and no spark on that either but it has a large gap...so no idea if the plug is bad or not. It was a cheap plug that came in the kit with the fuel lines.

What size line did you use?

Great instructions but I have one correction. The short port on the primer goes to the tank and the longer one goes to the left side of the carb. I did it the way you mention and the primer does not fill up with gas. I swapped the lines and now it does. If you look closely above the short port it says "IN".

I have McCulloch 3816 saw I purchased new 20 some years ago. My fuel lines are all cracked and disintegrated. The question is no one knows is the top or bottom hole in the fuel tank for the fuel filter? My lines were all broken off so I could not tell. I called the company now who owns McCulloch and they had no idea. I noticed in your video you put the fuel filter in the top hole. Do you know for sure it was originally like this? I want to keep it like it was from the factory. Thanks. Dan

It didn’t even run and it still ran better than mine lol

I have a saw just like the one on this video, I have been all over the web trying to find one who carries these parts. I need a set of the started paws on the pull rope. Would like to find more info on this saw for future reference., thank you for your help.

If it ain’t broke, I don’t own it! I would fix it!

Fun small saw. We have two taiwanese copies of this saw both 38cc. Both have oiler issues. One excessive oiling and now no oil anymore and the other one no oil. So I need to take them apart both to check the oil pump and line. Carburetor type is Walbro WT439. One saw has probably issue with the carburetor (checkvalve or metering diaphragm issue -- flooding ). If idle speed somewhat low it falls on its face when releasing throttle from full speed

How old is this chain saw? and Happy Thanksgiving!!!

I run my echo cs 300 evl without a muffler

Wow that saw was a mess!

Oops, 6:30 says to put both lines from the bulb to the carb.

Is that fuel line actually Tygon, the brand name Tygon USA appears in white letters on the whole length of the line I have! ?

I would do the work myself. That’s how you learn to do things yourself.

I would still make sure that oil cap does not leak.

A friend of mine gave me a Mcculluck 14”bc he couldn’t figure out why it leaked oil, I took it apart and found that the threads on oil tank had split, where can I find another oil tank. 3200 Mc TIA

house garage should be short videos and inside house garage should be the longer repairs

We have Gas Fuel Line Kit that may fit your equipment. We're happy to offer you the product completely free of charge in exchange for a video review. Do you need?

1:30 can't you just take out the plug, leave it connected and check for spark with the spark plug outside the unit? Most people don't have the tester

Those are junk! It may start but that'll likely be the best news you'll get. The oil pump is usually the 1st thing that breaks. It's twixt the flywheel & the crankcase. How many of these do you want?

I think I see why they discontinued this saw...

that looks like a hardly used chainsaw just been sitting with old fule , my first saw looks way worse lol

Those have very fragile oil pumps, it's twixt the flywheel & crankcase. They're low on power & do fairly well with a 14" bar, better with a 12". Have 3 of these given to me & I won't do anything with 'em except use for parts. They're a Chinese POS!

Chainsaws are a pain

I apologize Wrong video

👍👍отличная пила👍👍