How to install a shore power inset on a van conversion. Ford Transit 2020 AWD. Amazon link to Noco Shore Power Inlet: amzn.to/2uUDDpd
Пікірлер: 23
@AJourneyOfYourSoul3 жыл бұрын
Thank you for posting this. It is a very good idea to not have to drill a large whole in the side of the van. You did a great job installing it.
@jeffgalbraith74723 жыл бұрын
A little late for you now but for anyone else doing one of these vans..... If you pop that cover off like you did underneath, and then pop the cover off for the light switch, it's hollow all the way down to the bottom to where that bottom cap is. you we'll see a rubber grommet that can be pushed out and reused. That's where you could run the cable from outside to inside the van. You can just reach down there with your hand and pull it up, then there's a gap in there somewhere where you can put the cord to go towards the front of the van.
@susansmith20393 жыл бұрын
Thanks for letting us know Jeff, I will be checking that out.
@george19843 жыл бұрын
Thank you . But what's mean for "and then pop the cover off for the light switch, "
@offgridyo91942 жыл бұрын
That's good to know! In this case I prefered to have all the wires come through a hole in the plywood wall close to all my electrical connections.
@mccarthyhome4 жыл бұрын
Becky will never figure that out! Great install!
@StanBoIFX3 жыл бұрын
OH boy I am borrowing this one. Thanks for posting :D It is also nice that you didn't have to lop the head off the cord. The rectangle spot is big enough for the plug. Sweet.
@exechobo3 жыл бұрын
Clean install. This is where I ran 30amp into my Promaster. I will be running 15amp into the new Transit here too. Thanks for making the video, please keep it up
@susansmith20393 жыл бұрын
Can you run a 30 amp into the Transit too? If not why? Thanks
@campervibe4 жыл бұрын
Nice video, was one of the most confusing things we've done so far
@MovingToMnPro2 жыл бұрын
@4:33 I'd still add something behind for the srews to go into and keep the plug from being able to be pulled out.
@bchaszar3 жыл бұрын
I would be very worried about that wire rubbing on the sharp edges of the rectangular cutout. Definitely recommend some protection there.
@offgridyo91942 жыл бұрын
Several layers of cloth/soft electrical tape.
@KenBeaconHill3 жыл бұрын
Thank you!,
@peterwharton5649 Жыл бұрын
Hey I just purchased the new ford transit 2023 high top and I want to put in a switch for the rear cargo lights. Right by the back rear driver side door just where you are installing your stuff. There is a plastic plate with a switch on it that controls the rear cargo lights. Is it possible that I can get the information on that cover plate and the switch information so I can get one to put on my Ford transit 2023 thank you so much.
@MikeReyher Жыл бұрын
I will share with you what I have learned both first and second hand. Mine did not come with the switch on the back door jam. It's just a blank plate. The other thing to know is the rear cargo lights are controlled by the CAN bus and Body Control Module. So the switch does not break the power circuit for the light but rather sends a "press" signal to the BCM and then the BCM executes as programmed. If you don't have the switch it's possible you don't have the programming in the BCM. I ended up taking the factory lights out and installing my own LED lighting powered by the leisure battery bank. I hope that helps!
@offgridyo9194 Жыл бұрын
And I just discovered in fact I do have that switch. I was thinking of the 12v socket that Ford left off at the factory. My bad.
@gdufour13 жыл бұрын
How has this worked, has the plug stayed dry? Any changes you would make after all this time?
@bchaszar3 жыл бұрын
This is such a great question! KZfaq and Facebook are loaded with people doing these things for the first time and exclaiming that its the absolute best way ever, even though they have no idea. (Not at all saying that's the case here, but....)
@offgridyo91942 жыл бұрын
You guys can see how things have gone over the past months/years at offgridyo.com. So far all is well.
@offgridyo9194 Жыл бұрын
Still going strong.
@Jamie-re9cv Жыл бұрын
Why cut a corner off when you can drill a hole
@MikeReyher Жыл бұрын
The plug on the end would have required too large of a hole to thread it through so I am either clever or lazy or a nice mixture of both. ;-)