On the side walls the small additional foam pieces should be at floor level. That way heat loss from the seam is less and easier to install. Instead of being on a ladder.
@tphill663 ай бұрын
I just purchased a 30x30 garage from big building direct and I was researching on insulating it and came across your video, I’ve seen guys put furring strips up and using adhesive and double sided tape and all kinds of things I would have to say I love the way you are doing this with pressure fitting. It’s clean and the table saw is giving you a nice square cut and I will be doing the same thing! Thank you for this video. You wouldn’t have to have an updated video on how your garage feels after install would you?
@Steveoman19643 ай бұрын
I am glad you liked it. I should have an update soon
@RearviewMirror-ij2pr8 күн бұрын
Make sure you allow an air gap between the foam board and the exterior walls.
@Steveoman19648 күн бұрын
O yes about ¾ inch
@RearviewMirror-ij2pr8 күн бұрын
@@Steveoman1964 That works.
@billlevassiur5891Күн бұрын
Great cost savings. Looks good. Can you update on how the temperature inside is
@Steveoman196423 сағат бұрын
Sure not done yet will upday
@Condor1970Ай бұрын
I really wish I could go with a regular garage door like yours. I need the roll up door if I want to install a lift. Otherwise I can't open the door when my truck is on the lift.
@royweatherford645 ай бұрын
Trick with the foil tape if you get hvac all weather tape it will stick much better and if you put a strip of duct tape first it will even stick better . Or just silicone in between the joints
@Steveoman19645 ай бұрын
Thanks
@USMC-Sniper-013714 күн бұрын
I would have laid them flat on a clean floor so they don't get any memory bends in them from leaning against a wall
@cae20244 ай бұрын
We are getting ready to build a 26x40x10 steel building. What dimension size did you go with for footer and small support wall? Finished project looks really nice.
@Steveoman19644 ай бұрын
Sorry for the delayed reply I have a 24 by 50 and the footer is the same , i used a 2 by 4 around the footer for the steel Never lets water in
@MalleusDei27523 күн бұрын
Couldn't you overlay the foam board with the sheathing on the outside of the metal studs? Working great on mine.
@Steveoman196422 күн бұрын
Still working on the ceiling
@MalleusDei27522 күн бұрын
@@Steveoman1964 works on ceiling and roofs. The heat won't transfer with the metal then....
@danm667 ай бұрын
Did you seal the gaps at the corners and roof eaves? How about above the roll-up garage door?
@Steveoman19647 ай бұрын
Yes using spray foam from a can in corners Thanks
@TrapperSamm3 ай бұрын
I would hook my shop vac to the dust port on the table saw to control the mess.
@Steveoman19643 ай бұрын
Thanks I will for sure
@jordantheallmighty2 ай бұрын
A lot of shop-vacs cant keep up with the output of the saw. Might have to check if the hose gets clogged, if not the foam gets hot and melts to everything.
@luvmysuperdutyАй бұрын
I would try house wrap tape. I have some and you better put it where you want it the first time!! 🤣🤦🏻♂️🤷🏻♂️
@Steveoman1964Ай бұрын
Thanks I will
@MalleusDei2754 күн бұрын
Why not hang the foamboard between the frame and siding....?
@Steveoman19643 күн бұрын
It's 2 in thick
@MalleusDei2753 күн бұрын
@@Steveoman1964 even better..... Wider corner trimmed...😉
@hhipoolman3 ай бұрын
If you're going to heat the space wouldn't it be better to have the foil side facing inside the garage to reflect the heat?
@Steveoman19643 ай бұрын
Hi yes you may have a point but iam thinking of the heat in the summer as well
@NATHANHolland-ti2br3 ай бұрын
Where did you purchase the metal straps from?
@Steveoman19643 ай бұрын
Home Depot
@davidmembrila8041Ай бұрын
I read the foil part goes in the inside to act as a element for heater and AC like conductor. ?
@Steveoman1964Ай бұрын
Not sure keeps the heat out aswell need to dig into it more
@cae202419 күн бұрын
When they install the bubble wrap when installing building they put the foil towards the outer panels to stop heat penetration to keep your building cooler on the inside.
@arkansasboy453 ай бұрын
Is this going to take care of any condensation?
@Steveoman19643 ай бұрын
This will and already has stopped any condensation
@amonslow6 ай бұрын
where did you buy the foam? Home Depot wants $35 a sheet and goes down to $30.56 a sheet when you buy 10 or more where I live
@Steveoman19646 ай бұрын
I bought it at Home depot in Ontario Ohio other Home depot stores had different pricing Go fugue
@amonslow6 ай бұрын
@@Steveoman1964 I live in Washington state. I just ended up going inch and a half for $18 after bulk discount.
@Condor19704 күн бұрын
Have you noticed any sagging or fall down since?
@Steveoman19644 күн бұрын
Yes if it's not strapped it wants to wiggle out
@mattparks70613 ай бұрын
hello, i am looking around for a metal building, how was your experience with the building company?
@Steveoman19643 ай бұрын
Not to bad just make sure you know exactly what you want , do your research
@clo59373 ай бұрын
I wish I could have done mine that way my roof joists or legs are 4ft 10in wide inside to inside. I have to cut ever section lol. Nice work though.
@WindRider16 ай бұрын
If you put the silver side showing the metal tape will stick.
@Steveoman19646 ай бұрын
The foil tape iam using now works great 👍 thanks
@davidmembrila8041Ай бұрын
I read the shiny side goes pointed inside? To act as a conductor for heater and AC ? Is this true.
@chaney_WalkedU4 ай бұрын
Should have gotten a couple other quotes 🥴 30x70x14 with closed cell is 4200
@Steveoman19644 ай бұрын
Not bad
@franklinbrown84173 ай бұрын
Not where I live. I got a quote for 2” of closed cell foam for my 20x20x9 metal building and it was 5600!
@Pajake5702 ай бұрын
not sure i'd trust someone with that low of a price. 5000 from multiple quotes for 24 x 35 x 9 here