Is this the cleanest 250k mile 3rd Gen 4Runner EVER?!

Рет қаралды 32,901

2 жыл бұрын

Leaving out a ton of new OEM maintenance parts here:
Axles:
• OEM Toyota eLocker rear axle, built by Rock Rash Performance in Fayetteville NC
o Nitro Gear 4.88 Ring and Pinion set
 all new OEM axle bearing/seal parts, including:
• New Wheel Bearings 3634-0020
• New bearing case housings 42421-35030
• All 8 new axle studs to housing (4 each side) 90114-10016 + 8 nuts 90179-10067
• Rear axle oil seals 9031050006
• Bearing retainer o-rings 9030188077
• New axle shaft snap rings 9052036045
• New ABS rotors/ tone rings 4351735010
• All 4 new axle bearing retainers 4242320010
• Rear diff plug, new 9034118006
• NEW Aisin SAT-008 E-locker actuator/motor/and wiring kit
• New elocker shaft retainer- 41469-60010
• New shaft retainer bolts 9010508214
• SlagFactory New Grade 10.9 stainless button-head studs for 3rd member, with nyloc washers
• New elocker position indicator switch- 84222-12010
• New Marlin Crawler 112mm elocker studs and hardware
• Marlin Crawler ¼” thick rear diff armor, full coverage
• EimKeith rear upper control arm reinforcements welded in
• 12Volt Guy standalone e-locker harness set up
• Nitro Gear 4.88’s in the front differential
o Detroit True-Trac 7.5” Limited slip differential
o East Coast Gear Supply clamshell bushings
o New OEM inner CV oil seals
o DuroBump front diff mount bushings
• Rear diff breather extended to fuel filler neck, using all OEM new breather, nipple, and high-quality aftermarket braided steel line.
• eLocker breather extended up into the cab through fuel tank area
Brakes:
• Tundra 199mm calipers, Centric e-Coated 2001 Tundra Rotors, and Akebono Pro-Act ceramic brake pads + all new Centric zinc-coated front brake hardware.
• Toytec extended length braided stainless steel rear brake line (Body to axle)
• New OEM Toyota rear axle hard lines (Driver 47326-35062) (Passenger 47325-35282)
• New OEM Advics WCT08 1” rear wheel cylinders
• New OEM Toyota rear brake shoe set, with new drum brake hardware kit
• StopTech (Centric 950.44014) Tacoma stainless braided brake lines with banjo fittings
• New Brembo rear brake drums
• Sonoran Steel rear parking brake cable bracket
• ABS on/off toggle switch
Suspension:
• New OEM Toyota lower ball joints
• ARP Stainless 180k psi 763-1003 Lower Ball Joint bolts
o ‘02 Spindles gusseted with Total Chaos Fab Gussets. Seam welded both sides.
o New OEM Koyo bearings
o New OEM bearing snap rings
o New OEM hub interface dust seal, and rear CV oil seals
o New 1st Gen Tacoma Hub assemblies with new 4-pin lock nuts
o ARP extended length wheel studs
o Marlin Crawler manual hub hardware- new. Cone washers, studs, etc
o NEW OEM Aisin FT-019 manual locking hub bodies and dial interfaces
o New lifetime warranty NAPA MaxDrive CV axles
• BTF Fabrication Uni-ball Upper Control Arms with Energy Suspension bushings
• OEM front lower control arms rebuilt with new Whiteline poly bushings, gusseted/reinforced with EimKeith materials
o double-shear shock lower mount.
• New OEM alignment cams, tabs and through-bolts (eccentric).
• Steering shaft spot welded for rigidity + tilt knuckle ball shimmed to make it tighter
• New OEM Toyota rack and pinion system, including new inner tie rods .
• New Polyurethane steering rack bushings
• New OEM Toyota outer tie rods
• New OEM Toyota high pressure steering lines and high pressure switch
• New OEM Toyota Intermediate Shaft
• Eibach Pro-Lift Front kit including: new front struts and shocks (coilovers)
• New KYB front spring Isolators and installation parts+ 2” extended length top hat studs.
• Bilstein 5160 rear remote reservoir shocks, with custom aluminum resi brackets.
• Metalcloak Jeep JK front 2.5” Dual rate coil springs installed in rear
• Sonoran Steel fully adjustable rear panhard bar
• EimKeith panhard correction brackets- corrects panhard angle from lifting
• EimKeith front strut tower top plate reinforcement, welded on.
• Camburg 8” front suspension limiting straps with KarTek adjustable clevis and shackles
• Durobumps front and rear bumpstops (5.25” rear)
• OptOffRoad adjustable rear upper control arms with Johnny Joints
• New OEM Toyota rear UCA bolts and nuts (x4 each)
• Total Chaos Fabrication 1” front differential drop kit to allow correct CV angle
• 01-02 Toyota Tundra 16”x7” OEM Steel Wheels powder coated
• BFGoodrich KM2 255/85/16 MT (Load Range E) tires all around
• Shrockworks 3/16” steel Radiator, Engine, Transmission, Transfer case and gas tank skid plates- Powdercoated black- Full set of everything they offer.
• Rokmen DOM tube rear lower control arms with poly bushings and new OEM Toyota hardware
• ARP Extended length Wheel Studs all around and Muteki 12x1.5 open-face lug nuts.
• RadRubber Designs engine splash guard set.
• AMP’d Up LLC bolt-on front winch plate with 10.9 graded hardware
• Factor 55 Hawse 1.5 fairlead
• Factor 55 flatlink e and rope guard
• CustomSplice 3ft synthetic winch rope sleeve
• Warn VR-10 EVO Synthetic line 10k Winch, wired or wireless capability

Пікірлер: 228

@bernardcarpenter6949 2 жыл бұрын

This rig is awesome. Love the wheels and tires. The undercarriage is well taken care of. It's nice to see someone take proper care of their rig like this. Well done sir.

@4funner66 2 жыл бұрын

Thanks sir!!

@sapclan2896 11 күн бұрын

This an great example of an stock/oem look but everything fully upgraded. Def good reference for my 99 Limited I just got. Awesome build

@4funner66 11 күн бұрын

@@sapclan2896 thank you! That was exactly my intent with it. I didn’t want to disturb the body lines and design that, in my opinion, Toyota got perfect. But I still wanted to tap into the capability side while keeping that. Sort of a “sleeper” off-road build. Good luck with the 99, enjoy!

@seanhealy7 2 жыл бұрын

My man, that is one clean 3rd gen. I bought mine in '18 and have been scheming/buying parts ever since. Nice to see similar products (4th gen 5160's, eimkeith products) look so damn good installed.

@4funner66 2 жыл бұрын

Awesome!! I also bought this one in 2018. Good luck with yours and enjoy it!

@nathanr25 10 ай бұрын

That truck is SUPER clean! That's the cleanest 4runner I have EVER SEEN!!! I'm runnin a 97 4runner SR5 4x4 with 180k miles! Yours is way cleaner! I have done a bit of work to mine but really minor things compared to this. Replaced the gold badges on it because they were corroded to the silver badges, repainted the lift gate trim near the latch, got a different hitch from the junk yard and completely refurbished it, got TRD off road tacoma wheels, new center console lid, new lights for my climate controls, installed an OEM roof-rack, installed an OEM spoiler, and did a little rust clean and touch up OEM paint work to that rust on the lift gate. My truck has a major OEM chrome and black theme to it thanks to the trim and trd wheels and I LOVE IT!

@stevevice9863 2 жыл бұрын

Nice 4Runner! That might be the cleanest 3rd gen I've ever seen. I have a 2000 4Runner with 230K that has been in the family since new. It has been well maintained, but not as clean as yours. Drove it to CO from KY last summer and took it over Engineer pass and Imogene pass with out any issues. It climbed over everything in it's path. Great vehicles!

@4funner66 2 жыл бұрын

That is awesome!

@dozercass69 Жыл бұрын

Amazing machine. Well executed, no fluff. I love it

@jackrogers6792 3 ай бұрын

Well done man, just got my 01 4Runner same color and everything. Super clean, got an incredible deal on it

@sergioramirez1693 2 жыл бұрын

That undercarriage looks clean, looks mint like it can off the line. Really nice ride man. Respects to you

@4funner66 2 жыл бұрын

Thanks man, means a lot!

@1malikalik 2 жыл бұрын

I agree, this is T.H.E C.L.E.A.N.E.S.T 4 Runner. I Love the OEM LOOK. I pray this truck will serve you well and may your kids grow up to appreciate it, inherit it, treasure it and enjoy it. Be easy Champ. Am next door to you, Georgia. You got me subscribed and motivated to keep my 99 looking Clean and OEM

@4funner66 2 жыл бұрын

Thank you, Malik! This means a lot to me. I also pray that my kids can enjoy this truck loooong into the future. They are already familiar with camping trips and off-road trips with it. As long as I can preserve it, the bones of the truck should last forever theoretically :)

@freedom0855 Жыл бұрын

Sweet build! Brings back memories of my ‘99 4Runner SR5 - same color inside and out. Looked just like yours. Put the Sonoran Steel 1.2 lift on it with 285/75/16 tires. Had it from ‘05-‘15 and lived out of it during the week for 4 semesters in college a couple hours from home. Didn’t want to pay rent so removed the rear seats and a blowup mattress fit perfect. Slept in it Mon-Fri and went home for the weekends. Had to sell it for a down pymt on a house. Have had a ‘79 Toyota 4x4 and a ‘99 Tacoma TRD Off-road since but really liked the balance of the 4Runner and flex of the rear 5-link axle. Was going to suspension lift the Tacoma but the frame rust was out of control, so sold the truck. Miss the 4Runner though. Really like your ABS mod and e-locker install. That’s a keeper!

@speedy94- Жыл бұрын

I had a 95 4runner with 255k on the weak 3.0. Only done head gaskets once. Recently swapped In a 3.4 and it’s now an amazing ride!! Yours is definitely a worth wild build, super nice

@scottieb6331 Жыл бұрын

Great video man!! Thank you for sharing all your info! Very helpful

@ErvinuxYEAH Жыл бұрын

Very clean, I was really amazed👍

@professoraregbesola3490 2 жыл бұрын

This is one of the nicest 4 runners I have ever seen. Normally I'm not big on the cloth seats but it's definitely nice.

@4funner66 2 жыл бұрын

Thank you! I’m not normally a cloth person either - or a blue interior person :). But, with this one i didn’t think twice and couldn’t refuse it! It has grown on me majorly, and I may even prefer it over Tan interior

@RamDude87 2 жыл бұрын

Awesome build! You have fun with it but you also keep it clean 🤙🏼

@nathanjohnson3790 10 ай бұрын

WOW!!! This Truck Is Beyond SWEET!!! Very NICE!!!!

@v-modsolutions6946 Жыл бұрын

That frame is amazingly clean, aside from all the upgrades, very very nice!

@4funner66 Жыл бұрын

Thank you!!

@Lanierkayakfishing 2 жыл бұрын

Awesome rig! I have a 99 same color with 241k, very similar southern truck that is super clean underneath. Owned it 4 years just hauling my kayaks and an occasional camping trip. Considering a build and turning it into my daily driver. Defintately more inspired seeing yours now thanks for sharing.

@4funner66 2 жыл бұрын

Excellent!! Take care of it, and enjoy! These trucks are appreciating assets. Kind of cool to be able to Daily something that is actually going up in value haha

@Lanierkayakfishing 2 жыл бұрын

@@4funner66 I figure I will need to invest a few grand depending on what I do but on paid 3k for it in 2017 and used car prices are crazy right now. Hard to believe the 3rd gen runner is now vintage but it is getting harder to find nice ones now.

@colinjames2383 2 жыл бұрын

Subscribed!!! Nice looking 3rd gen 4RNR. Very clean!!!

@4funner66 2 жыл бұрын

Thanks man! I hope to make more videos that are less boring than this one. I’ve got a lot of wheeling footage I should stitch together

@snailwigs 3 ай бұрын

Super clean, nice shoes!!

@kevinsilverthorn5235 Жыл бұрын

Nice rig man I have a 98 one owner. My dad bought it new. I bought it from him after hassling him for 15 years to sell it to me. it’s super clean but your rig is at another level,

@92littlebluefox 2 жыл бұрын

Nice ride. Looks great!

@mauriceescobar8403 2 жыл бұрын

I have that same winch mount on my 96. Albert does quality work👍🏼. Your 4runner is top notch.

@4funner66 2 жыл бұрын

Thank you!! Albert is the man!

@ShellbackUSN 11 ай бұрын

Beautiful 4Runner!

@3gen4life 10 ай бұрын

Bad ass truck just got mines 4 days ago planing on keep it like that

@gulenator Жыл бұрын

Beautiful truck I aspire to build mine like that someday, I'm working on making my 2wd as nice as possible, I don't have the time or space to wheel as I live close to the city but this thing is sweet!!!

@zacharyvillanueva955 Жыл бұрын

Beautiful ride. Truly well done

@4funner66 Жыл бұрын

Thank you

@JoeBlunt Жыл бұрын

Kind of a sleeper have to get underneath to see how much care went into the build awesome rig

@Dogtown21 Жыл бұрын

Yeah id say its built… great Work. Second I saw the panhard I knew what time it was. Beautiful 3rd gen

@CoolFrijolez 2 жыл бұрын

Damn dude I was not expecting all those tasteful mods, good taste man!

@4funner66 2 жыл бұрын

Thanks man!

@Rick_Rdz 2 жыл бұрын

I love mine!! My father bought right off dealer lot and still in the family..... 02 silver with 419,000 all OG. still runs like a champ💪🏻

@4funner66 2 жыл бұрын

Incredible! 419k! Wow

@lovenliberty5708 Жыл бұрын

Absolutely beautiful. I wish my frame was that clean but it's got plenty of rust. Keep yours this nice so your kids can put it in your family museum one day, haha

@lovenliberty5708 Жыл бұрын

Coming back again a day later to admit I am still suffering from frame envy

@blapblapism 2 жыл бұрын

I love the OEM sleeper look also.

@4funner66 2 жыл бұрын

Thank you! I’d love to do an all-out off-road build with bumpers and stuff. But probably not with this truck, I just don’t want to ruin the stock look. I’d love to find more of a beater to do that to

@jasperbumgart1891 Жыл бұрын

Albert at AMPd Up is a genius. I'm running his custom bumpers. Love em!

@4funner66 Жыл бұрын

He’s a heck of a guy!

@Kingfisher1060 Жыл бұрын

OK there is no one on the planet that has a year Toyota 3rd Gen. Like you that's even close nothing's gonna be close close to yours as good as shape as it's in check the zoo I'm so proud you I'm so excited good for you dude I can't

@L0WPEZ1 2 жыл бұрын

Wow I can’t believe how impeccable that underside is

@4funner66 2 жыл бұрын

Thanks! It's really unusual

@alexandragarcia8784 2 жыл бұрын

beautiful 4runner!!

@4funner66 2 жыл бұрын

Thank you!

@markmcmanaman1282 Жыл бұрын

Ultra clean!

@jroyer09 Жыл бұрын

Wow! Very impressive! I guess I’ve got some work to do lol

@paradigmnine Жыл бұрын

All. The. Fun. Stuff. this right here is 3rd gen goals

@4funner66 Жыл бұрын

Thanks!!

@Mohamed.N.Y.C 10 ай бұрын

It’s a beautiful truck

@seanmchristen 10 ай бұрын

Love it!!

@Tac0caT0 Жыл бұрын

That’s a beautiful runner. Just got into a 2001.

@4funner66 Жыл бұрын

Congrats, how are you liking it?

@Tac0caT0 Жыл бұрын

@@4funner66 I’m pumped! Needs a new rack, and there’s a small leak in on the rear differential. Outside of that, she’s as solid as the day is long🤩

@orpiv 2 жыл бұрын

Im in NC too..I have a 99 Limited..Love it! I have TRD pro 17" gray wheels 33" Nitto Ridge Grapplers .. Really like the Steelies! would be great for an alternate mud terrain tires to switch out when necessary...I enjoyed the video, Thanks

@4funner66 2 жыл бұрын

Another NC person! Ever go out and do any wheeling on the beach, like Freeman Park- or out toward the foothills at Uwharrie? It’s the most fun you could possibly have in these trucks!

@scrambledgreg3834 Жыл бұрын

WOW!! Impressive

@3rdgenbestgen21 2 жыл бұрын

clean rig! And hey I did the manual hub conversion too😁

@4funner66 2 жыл бұрын

Haha nice! I’m digging the username

@3rdgenbestgen21 2 жыл бұрын

@@4funner66 lol thanks

@brandtall9639 Жыл бұрын

You put all your $ in the right places. Love "kid central".

@kiltedoverland4551 Жыл бұрын

You have a great looking rig! Hope to run into you sometime..

@gabe3366 Жыл бұрын

WOW, super clean build. How do you like the ride of the eibach shocks and 5160s?

@andygarcia6879 2 жыл бұрын

Beautiful just beautiful

@4funner66 2 жыл бұрын

Thanks, means a lot!

@stadhorn7708 26 күн бұрын

Beauty !

@EnriqueReyesJrREALTOR 5 ай бұрын

As Napoleon would say; “I like it a lot”! I have a 1998 4Runner, 4 cylinder, automatic, rear wheel drive. I put factory 17” take off wheels from a 2020 4Runner on mine with no rubbing. With the exception of on a hard left turn the back of front left (drivers side)?tire ever so slightly touches the factory mud Gaurd. Other than that zero rubbing.

@h.j.s.j.1801 Жыл бұрын

Nice 3rd gen 4runner I need to upgrade my 3rd gen 4runner

@ejamcast 2 жыл бұрын

nice !!! very nice!

@4funner66 2 жыл бұрын

Thank you sir!

@collingarrett5592 Жыл бұрын

literally the cleanest 3rd gen ive ever seen.. wow

@4funner66 Жыл бұрын

Thanks!

@raging_rhino2582 2 жыл бұрын

Bro I have an O2, how the hell do I get it this clean underneath? Holy cow... Everywhere ya look more... Well done bro How much lift is on it as it sits? I have the Bilstein 5100 / OME (height adj Fronts)

@burnhags2572 2 жыл бұрын

Beautiful rig. I’m running a third GEN full armor looking for a 3 inch lift what do you recommend? Wanting the 2.0 Elka coil overs don’t know if it’ll be able to handle the heavy load

@jdawg3712 2 жыл бұрын

I really wanted to "rip" on this thing. Hell I learned that frm the 3rd Gen Mafia. 😆 But this thing looks like it jest came off the assembly line. Beautiful 4runner man!!😎

@4funner66 Жыл бұрын

Hahaha the mafia is awesome. Gotta have thick skin lol

@kkainaluu808 2 жыл бұрын

Bra this is a clear runner, I have a 2000 millennium silver with the blue interior as well. I couple things u should look into is the Solo Motorsport’s stock length boxed LCAs. There pretty much stock geometry except the lower ball joint hole is pushed forward about 1” for more clearance and also has extra armor around the lower ball joint nut. And for the exhaust I highly recommend the cat back magnaflow overland series exhaust system, sounds really good and has absolutely no drone.

@4funner66 2 жыл бұрын

Thanks man! I looked at the Solo stock length arms! Pheeew they’re pricy. I just did whiteline bushings and eimKeith reinforcements welded onto my factory ones. Would be nice to get more caster capabilities though. As for exhaust, I’m leaving it for now since I plan to buy a 1UZ V8 to build up soon! This time next year or so, I expect it might be under the knife, so I’ll probably have to do something custom for the exhaust there

@kkainaluu808 2 жыл бұрын

@@4funner66 yeah the LCAs are a Bit pricey. Between those and my SPC UCAs set 2 notches forwarded pushing the spindle flowered I would say the front wheels have moved forward at least 1” 1/4. Choke room now. If I was gonna do v8 swap the flow master super 50 series would be my muffler choice. That muffler keeps that sound of a v6 but is able to handle a v8 well. I have a friend will a 4th gen v8 with that muffler and it’s 👌🏽

@hamalaw4490 Жыл бұрын

wow looks new

@jacksonwyatt952 Жыл бұрын

I have a 2001 that has 240,000 right now, im trying to make mine turn out the same as yours !

@WestCoastTug 2 жыл бұрын

Unreal! Have A 99 4runner and about a month out from installing my lift. Just ordered the rad rubber splash guards, thanks for posting those! I have a question about undercoating… did you do your self? What product did you use? Also are wheel wells done in same paint or different? Would love to clean up under carriage of mine before I do my complete lift. Thanks

@4funner66 2 жыл бұрын

Thank you! Im making a video for my next upload to explain the paint, process, what materials I used, etc - stay tuned!

@jvogler_art4708 2 жыл бұрын

Mine's this clean, but it doesn't have all the nice offroad upgrades like yours. Still stock with 4.10 gears and no e locker :\ Love all the armor reinforcements. If i had money i'd do the same to mine.

@4funner66 2 жыл бұрын

These trucks are well built in stock form! No need to rush any upgrades- enjoy the truck

@johnnyorrantia2476 Жыл бұрын

Whats the cost to do something like this, looks amazing under the car everything brand spanken new 🤩😍

@reynaldocastro6248 Жыл бұрын

Esta preciosa esa trova 4runner

@luism9678 5 ай бұрын

Badass Ride! You can eat off that chassis

@4funner66 5 ай бұрын

Thanks man. Been daily driving it and off-roading several times for the last year straight. You’re making me want to go clean it! Haha

@christinarainjoy6726 2 жыл бұрын

That is beautiful! Do you have a video about how you painted the underside?

@4funner66 2 жыл бұрын

Thank you! Thats a great idea and I can make that my next upload. I have lots of pics and can explain the process, what materials I used, etc

@christinarainjoy6726 2 жыл бұрын

@@4funner66 that'd be awesome. I have a 2000 low miles 4Runner and hardly any rust underneath but I'd love to keep it that way by painting it or putting some kind of sealer on the metal.

@blapblapism 2 жыл бұрын

Wow super rad rig, I Literally would never sell that thing.

@4funner66 2 жыл бұрын

I never will!

@09darkS Жыл бұрын

questions Metalcloak Jeep JK front 2.5” Dual rate coil springs installed in rear - 2.5inch for the jeep or the 4runner? just want to know how much lift also, where do you usually hang the keys? where do you usually park the vehicle? thanks. sorry for my english

@levimonsen1006 2 жыл бұрын

Can you do a video on those subs? I’m curious about them and how they fit and how you wired the two.

@4funner66 2 жыл бұрын

That’s a good idea! I could probably yank a seat out and try to describe how it’s all wired and fused. All the wiring is hidden though. If you’re curious they’re Alpine PWE-S8 subs

@FirstclassSnipingxD 2 жыл бұрын

Hey man beautiful build, Just got mine a couple weeks ago, and loved the yellow fog light set you up you have in the front, which ones are those exactly? Could you point me in the right direction, thanks!

@4funner66 2 жыл бұрын

They are sadly no longer sold/discontinued :(. I haven’t seen them in about 2yrs now

@21192jwc2 2 жыл бұрын

Damn this thing is incredible!! If you don’t mind me asking, how exactly did you mount those fog lights? Thanks in advance!

@4funner66 2 жыл бұрын

Thanks! I was able to re-use the factory brackets, but modified them slightly. No welding was needed. Had to drill an extra bolt hole in one location, and add a bolt/lock washer/nut. It was easy. If I can do it, anyone can

@21192jwc2 2 жыл бұрын

@@4funner66 Ahhh ok gotcha, see my 3rd gen didnt come with any stock fogs so i will be having to fab something up, maybe out of some angle iron or something lol. Thanks man!

@whoisandre1180 8 ай бұрын

hi, could you tell me how you put aftermarket foglights in the stock location. i want to put baja design s1’s in there

@orfanelaraujo6255 2 жыл бұрын

I need to get me a wheel set like that

@4funner66 2 жыл бұрын

Heck yeah! Cheap! 1st gen tundra base model/spares

@davescheer5038 2 жыл бұрын

Was searching for a 4 runner in my area , dude there harder to find than hens teeth , any four wheel Toyota ,nobody wants to turn loose of them , I wanted something to haul a small boat and go camping , well I found a 2002 4 runner with 187,000 but it is only 2wd and I got to thinking I don’t really go off road that much and I could always add a winch to help get me out of a pinch , when I saw your truck I said wow it’s a fine ride then I saw the the updates and said that’s a “dam” fine ride , when I got mine it’s white with gray interior, there wasn’t any paperwork that came with it but it’s clean ,has a few door dings , but it did come with free Disney stickers on the back window and some chocolate shake stains on the rear carpet 😊, I’m in process of going thru it from front to back to do all maintenance, it runs like top but needs valve cover gaskets , timing belt change , rear wheel seal, I’ve had it for about a month and a half and I’m in love !

@4funner66 2 жыл бұрын

Congrats on the 4runner!!! This one had its fair share of chocolate stains in it too when I got it! (GOD I HOPE THAT WAS CHOCOLATE)

@davescheer5038 2 жыл бұрын

@@4funner66 , chocolate 🤔? Just had the valve cover gaskets, PCV valve and grommet, spark plugs , wires , radiator replaced , new rubber throttle body intake , and rubber steering bellow, done , yesterday, $ 1300, still needs timing belt with bearings I’ll replace water pump and idler while getting that done and it still needs rear wheel seal , I just want to make it a reliable vehicle, the mechanic did point out there was a dead squirrel between the shroud and radiator 😳🐿👍🏼

@enk_10 3 ай бұрын

did you install your steering rack at the dealer? or did you buy the part and someone else installs it? 3:22

@luciagutierrez2050 2 жыл бұрын

Super clean super nice 3rd gen, kind of jealous. I’m still waiting on my bilstein 6112 & 5160s to come in. How did you put the scangauge on the Paranoid fab mount? if you don’t mind me asking

@4funner66 2 жыл бұрын

For sure, thanks!!! I used a thin strip of black 3M double sided adhesive foam tape on the back side of the paranoid mount for the scan gauge. Works well for about a year now

@luciagutierrez2050 2 жыл бұрын

@@4funner66 thankssss

@Stabilevincentc Жыл бұрын

Any particular reason why you didn’t use the factory 4runner steelis?

@justinearnheart2240 2 жыл бұрын

Awesome! Are your CVs a stock replacement or do you have high articulation CVs? Asking because I’m about to replace mine. I have a 3” lift on a 98 4Runner. Debating between OEM CVs or aftermarket high articulation CVs. Thanks!

@4funner66 2 жыл бұрын

They are stock replacements. I figure with the manual hubs they aren’t seeing a lot of stress in daily use so they technically should hold up longer. We will test that theory haha

@mikeysautoandelectrical5257 Жыл бұрын

I’m looking at years of work here. Very nice stuff. #3rdgenmafia

@4funner66 Жыл бұрын

Thank you! It’s a labor of love

@jasonphillips3282 Жыл бұрын

Question. Are you running wheel spacers?

@raymondgoodwin951 2 жыл бұрын

Love it! Did you have a hard time locating 1st gen. locking hubs?

@4funner66 2 жыл бұрын

Thanks!! I looked for months to find 1st gen taco hubs, and couldn’t ever get lucky enough. Finally broke down and decided to go 100% new on everything. Thankfully you can still buy the oem Aisin hubs and all of the associated parts new. Finding a used Tacoma for parts is the budget way to go, but after a year of looking around locally, I just got impatient lol

@raymondgoodwin951 2 жыл бұрын

@@4funner66 Good to know, thanks for gettig back to me

@thrRnz9496 2 жыл бұрын

Sweet Jesus!

@4funner66 2 жыл бұрын

Haha Thanks man

@kiltedoverland4551 Жыл бұрын

Do you have the part info for the Tacoma manual hubs? I'm also in NC and have '02 T4R

@schuylercholvitee2478 Жыл бұрын

Tried looking through the comments but didn’t see anything about it. You wouldn’t happen to have a link to the rear power supply you have would you?

@kkainaluu808 Жыл бұрын

Hey braddah howzit, do you by any chance have the part # for those extended wheel studs? LmK Mahalo 🤙🏽

@danielfigueroa7930 Жыл бұрын

Part number for the airaid intake tube? Amazing 4Runner !goes without saying

@4funner66 Жыл бұрын

airaid 510-934. A little expensive for what it is. Lucked out and found mine in the junkyard of all places. My original rubber couplers were cracking so decided to simplify things with the tube

@danielfigueroa7930 Жыл бұрын

@@4funner66 sure is a little spendy I might just cobble together something myself and call it good enough thanks for the info though !

@coryhaag6766 6 ай бұрын

What amber fog lights are those?? Still have the link?

@twelve_thirteen 3 ай бұрын

She's a beaut!

@jessierodriguez6368 Жыл бұрын

Badass

@michaelpaul721 5 ай бұрын

Nice care. Got dizzy though

@jimbo2040 Жыл бұрын

Nice runner. Wondering if you are running spacers for these steelies? I have steelies from a 2017 taco and wondering if ima be able to fit a taller tire without spacers

@4funner66 Жыл бұрын

Thanks! No spacers on these. You should be fine without them, although I’ve never tried a newer Tacoma steel wheel before

@viper14789 2 жыл бұрын

Very nice truck, one of the best out there that I have seen! Random question: Where on earth did you happen to find a Toyota center cap for a 16in. steel rim that you have in the back? Assuming that is a center cap and not just part of the mount... thanks!

@4funner66 Жыл бұрын

Thank you! That is actually a new-old-stock FJ80 rear center cap. eBay find. It “fits” onto the spare, just for looks. It would sling off if used at highway speeds, just not made to fit these tundra steel wheels well

@georgepadilla6697 3 ай бұрын

If I want a set of these steelies, where can I buy a set? This is the exact rim I've been searching for in 16in

@georgepadilla6697 3 ай бұрын

@4runner66

@georgepadilla6697 3 ай бұрын

@4funner66

@patrickvanbuskirk9376 Жыл бұрын

Awesome Runner! How have the jk 2.5" coils treated you? I'm looking to replace my 890s as I've added a steel bumper with spare swingout and 35" spare. Thanks in advance for your reply!

@4funner66 Жыл бұрын

The JK 2.5” lift coils are great for stock weight. They are very soft, and wouldn’t do well at all for your bumper and 35” spare. I’d recommend Landcruiser 7.5 wrap springs for that. They are the exact same ride height as the 2.5 JK Springs, but will actually handle the weight you have. You can even still get them new, too. Part # 48131-6A570 (x2). You can use an OME 10mm trim packer on the driver side to make the lean go away. :)

@patrickvanbuskirk9376 Жыл бұрын

@@4funner66 Thanks for the quick and concise reply! Glad those JK could are working out for you. I think I’ll go with the LC coils. You think these are the better option over 891’s?

@uyatemes503 2 жыл бұрын

🔥

@lucyrausch4 2 жыл бұрын

Awesome build man, are the tundra wheels 6x5.5? I just traded my 2004 Civic SI for a 1998 4Runner SR5 with 177k miles but it has rust because it’s been in WI it’s whole life. Maybe I didn’t catch it but what’s the front and rear suspension specs? I’m glad it doesn’t have the rear spoiler on it too

@4funner66 2 жыл бұрын

Thank you!! The tundra wheels are 6x5.5, yes. Full list in the description-- But, the short version is: Front is Eibach pro lift coilovers, middle notch, with 1/4" poly top spacers. Rear is Bilstein FJ 5160 reservoir shocks with Metalcloack Jeep JK (for the front of a jeep) 2.5 dual rate springs