JOYO PXL-Live Noise Gate and 4 Cable Method

Рет қаралды 9,088

3 жыл бұрын

Hey! Thanks for watching this video! Make sure to like, comment, and subscribe!
Signal chain in this video:
1. Guitar into JOYO Input
2. Loop 1 of the JOYO to the Sentry Input and Send to hit the front of the amp
3. Loop 5 of the JOYO to the Sentry Return and Output to hit the FX Loop of the amp
4. Loop 1 Out from the JOYO to the front of the amp
5. Loop 2 In from the JOYO to the Send of the amp
6. Loop 2 Out from the JOYO to the return of the amp
And boom, silence.

Пікірлер: 42

@theryguy9522 2 ай бұрын

This video was super helpful, thank you. For anyone else wondering this method does work with the NS-2 as well.

@dantrag2890 3 жыл бұрын

Hell yeah dude, glad you figured it out!

@randymccoy2527 7 ай бұрын

Great tones man! Sounds tight as hell to me

@jerrytrouble 2 жыл бұрын

Great information 😀

@elamordecristo1777 2 жыл бұрын

Wow men thanks for this video very helpful thank u thank u thank u !!!!!!

@kaihoosier4716 2 жыл бұрын

Thanks man, let me know if you have any questions!

@pod7450 2 жыл бұрын

sounds killer dude

@kaihoosier4716 2 жыл бұрын

Thanks man!

@BReal14 3 жыл бұрын

welcome, dude!

@MrDreamTeamGamer Жыл бұрын

I have an NS-2 so not exactly the same, but I go guitar into noise gate, then from the noise gate into the input of the switcher. I put the return and output in loop 5 of the joyo. This way I only use 1 loop for the noise gate

@kaihoosier4716 Жыл бұрын

Yea that’s how I used to have it! I discovered I just liked this way a little bit more as it seemed to be a lil tighter

@yannickcharron3193 9 ай бұрын

You could be using 0 loops for your gate while gating pre amp and fx loop.

@randymccoy2527 7 ай бұрын

How could I do this? I am new to using a switcher, but very familiar with 4 cable method into effects loop etc, I am buying a switcher and trying to learn as much as I can.@@yannickcharron3193

@qua7771 Ай бұрын

I have an MXR noise clamp. I may have gotten the wrong thing. Doesn't most of the noise come from the pedals that are in front of the amp, (distortion etc...)? The other thing is, I alredy have the inpus on the Joyo PXL used up.

@lucasricarte3156 Жыл бұрын

Hola tengo dos dudas no se puede usar en un equipo que no tenga loop no? y la otra como lo enchufaria a una consola si uso un pedal preamp?

@PanteraGs1 2 жыл бұрын

Hey, bro! What are those beautiful patch cable you're using there? They look high quality and so practical!

@kaihoosier4716 2 жыл бұрын

They are the Kurrent Electric solderless patch cables!! You can find a set of them on Reverb, I love them and they’re very easy to make!!

@PanteraGs1 2 жыл бұрын

@@kaihoosier4716 Thank you so much!

@kaihoosier4716 2 жыл бұрын

@@PanteraGs1 no problem man, let me know how you like em! I have bought the Daddario cable tester for like $15 or whatever just to test each cable, might save ya some hassle!

@romellliging4667 Жыл бұрын

thanks for the video..but can i use a behringer nr300 with the same method that you use?

@kaihoosier4716 Жыл бұрын

I’m not sure but I would assume so! Try it out and let me know!

@uptownphotography Жыл бұрын

Nice video. I am currently looking for an effects loop switcher. Not sure which to buy yet as I just stated looking...Good info... Phil

@kaihoosier4716 Жыл бұрын

I personally love the Joyo PXL Live, I have another video on how to use its midi features with an EVH. Just a good quality looper for a decent price, I’d definitely check it out!!

@uptownphotography Жыл бұрын

@@kaihoosier4716 Yes the model you have looks cool. I was also checking the Moen GEC9 unit, which is a little more money so I need to decide. I found a video that explains how easy the Moen is to program... kzfaq.info/get/bejne/aLmSn7ycnLuyaX0.html

@kaihoosier4716 Жыл бұрын

@@uptownphotography I looked at the GEC9 but there does not seem to be a lot of info on it and seems to be a little more complicated

@uptownphotography Жыл бұрын

@@kaihoosier4716 The Moen V2 (version 2) is the latest one and pretty easy to program. I just don't know if i would like to spend the extra money however as i don't use a lot of effects. The JOYO unit is cool too. Both are quality units I'd say...Thanks... Phil

@matthiasmauri6335 Жыл бұрын

Hi, thanks for the video. What if I would do it like this: Sentry input - from guitar Sentry output - to amp Sentry send - to PXL input Sentry return - from PXL output Shouldn‘t that work as well? So I don‘t have to use any loop.

@kaihoosier4716 11 ай бұрын

That might work but I personally like the gate the loop of my amp to get rid of the hiss that is produced from the power amp

@yannickcharron3193 9 ай бұрын

That would be the proper 4cm way to do it. It gates pre amp and fx loop while saving 2 loop slots.

@andrewbickford6170 6 ай бұрын

@yannickcharron3193 and then just plug all remaining pedals (I have 8) into each individual loop of the switcher?? 🤔

@DAVIDMARAFIOTI Жыл бұрын

with your EVH 3 channel switching clean / crunch / gain - how do you change these channels selections with the PXL?

@kaihoosier4716 Жыл бұрын

I have a video where I cover that! Check out my channel for a full walk through of how to do it!

@gazzaduce3424 4 ай бұрын

@@kaihoosier4716 thanks for the helpful video. I have a quick question. Where will I put my wah pedal in the chain? Is it after the noise gate and am I created a send and return for that pedal as I see in some diagrams some people plug guitar into wah then wah into the in of the Joyo pro so just about confused by it and I’ve just subscribed to your channel 😊.

@Mitsui990 Жыл бұрын

Hey man, thank for this video but i have a question for you: i have the same loop switcher and the same Sentry, but i don't have s/r of the amp. How do i do for use correctly the Sentry? I want it to go after od and fuzz pedal, where the noise is. But I really don't know how to collocate it in the looper switcher. Do you think it will be ok to do the same thing as you even without fx/loop of the amp? Will it work? Hope you can help me, thx!

@kaihoosier4716 Жыл бұрын

Hm that one is definitely a little more complicated. I would recommend you out the sentry before the amp/pedal distortion you are using while keeping the fuzz in front of it. I think that might work

@BReal14 3 жыл бұрын

I'm not familiar with the sentry but this seems incorrect to me: 2. Loop 1 of the JOYO to the Sentry Input and Send to hit the front of the amp 3. Loop 5 of the JOYO to the Sentry Return and Output to hit the FX Loop of the amp Shouldn't the Input go to Output, and the Send go to Return? I would have done it like this: 2. Loop 1 of the JOYO to the Sentry Input and OUTPUT to hit the front of the amp 3. Loop 5 of the JOYO to the Sentry Return and SEND to hit the FX Loop of the amp

@kaihoosier4716 3 жыл бұрын

Unfortunately I had the same mindset and it caused so much confusion when I first got the sentry but I’m pretty sure this is the correct way. The input of the sentry is typically for your guitar, the send goes to the front of the amp, the return catches the fx loop, and the output sends out the signal. I’m pretty sure that’s the the sentry is supposed to be used from what I’ve seen of diagrams showing ways to use it. You can google ways to use sentry noise gate and you’ll get some diagrams that help show it. Thanks for the comment!

@FuturoAnacronico 2 жыл бұрын

@@kaihoosier4716 Im setting a pedal board with a different approach to the Sentry. Guitar Goes to the Sentry Input. Sentry Send goes to Wha Pedal Before the switcher. Wha output goes to Loop 1 input. Loop 1 output goes to the Amp Input. Amp Send goes back to the Sentinels Return. Sentinels Output Goes to the Loop 2 Input. This way all the loops from Joyo Loop 1 handling gain or and distortion as well as the amp are inside the sentinels noise gate loop. Second loop has an EQ, a Volume pedal and a Helix Stomp. I can bypass all the pedals in the first loop to go directly to the helix stomp if I want. I can also by pass the Amplifer preamp if you connect the L4 send to the input and the amp send to the L4 Return in the 1st loop, if that is the case Loop 1 output goes to Sentinels Return and Sentinels output goes to Loop 2 input. Remember that Stereo Effects that dont use distortion shouldnt create more noise, therefore you dont need to keep those in the noise gate loop.

@yannickcharron3193 9 ай бұрын

You got it right mate. That would gate pre amp and fx loop and save 2 loop slots.