Nice one easier and straightforward to follow with no excessive yacking

Nice video and Rover! Makes it looks easy and to the point. 5 stars ⭐️

Thank you that was a very informative demonstration

Really useful. Thanks pal!

I tried once but couldn’t get the big nut out with all the might and power I had. I am motivated to give another go after watching your vid. Thnx

Thanks 👍 really helpful

Great video helped me do my bearing without no mechanical experience (didn’t have impact) had to reassemble to put wheel on haha

Great video, you should do a walk around on your suspension set up, looks great

Hello Mr Tabb88. thank you for the great video. I completed the task however the who shaft came out. when I pulled it apart. wondering if that's normal or a sign of something else.

Hey great video, thanks a lot! You mentioned the torque nm at the end but did you use a torque wrench at all? I have an impact driver (Ryobi), but its not a torque wrench. Subbed!

Hey mate, Great video and referenced to it a few times over the last couple of days doing same job on mine. I noticed u have an aftermarket washer bottle on the bulk head. I have just purchased the same kind. Did you just bolt it in place, connect up the windscreen washers and not bother with the rear window and headlight washers? Connect up the red connector from the existing washer onto this new after market one?

Great video thankyou, can I ask what brand wheel bearing did you fit ? Has it held up ok ? I'm about to do my front bearings on my d2, great video 👍

How's the project going? You welded up that rusted spot yet? It's like youtube knows I orderd a new bearing kit for mine. This was a video it thought I would like. Thanks I know I won't have any issues but I'm sticking new disks and pads in well I'm there so will have to do the other side not long done the front breaks but ended up getting some discount on brembos all round so had to get them. Your engine layout is abit diffrent than my td5. And although mines just as dirty my engine bay and underneath looks then times cleaner. I even have those shocks front and rear but stuck with the bags on rear and uprated springs, so still stock height

Awesome video. I do have a question for you. What size are your wheels? I love the stance your Disco has.

Do you have any videos on doing the CV joint? Mine has started making a popping sound when I turn but only under throttle not rolling. I found one of the boots broken and I do a lot of deep mudding and pretty hardcore desert stuff over here. I'm looking for a good straightforward video on that but a lot of them have way too much talking and too much confusion like they were trying to figure it out on video not really knowing ahead of time exactly what they do

Hello what diagnostic tool or kit do you use for ur land rover?

what wheels are those? what size tires and do you have any rubbing?

Very clear and helpful video, thanks shearing. Which shocks absorbers you use in the front ? What is your general opinion on the Disco 2 td5 ? Which year model is it ?

Yes, very good video. Quick question. Looks like you have oversize tyres on the car. What size are they and what did you notice in terms of (loss of) acceleration etc of the car due to these bigger tyres. Your comments would be very useful. Thanks.

What wheel specification are those chap? Looks great

Hi mate, when u was threading the abs wire through the inner wing at the top, I noticed that the inner wings outer edges are totally rotten, mine are too but maybe not as bad as yours, I just wondered is that a major problem ? or an easy fix, if so, how?. and is it a mot failure ?. do u intend to fix/weld yours or leave it as is. interesting to know, thanks a lot, dave

Did you use a torque wrench as well to tighten the hub nut up?

Great video ,what is size of tyre and rims?

What wheels do you have? Really nice offset

Good luck getting the hub nut off. I had to buy a new shaft with hub attached

I'd like to see you use stronger axle stands. I've seen those pressed steel ones collapse.

awsomme vid . 👌👍 what suspention do you have ?

What wheel & tyre size are you running??

What wheels you running? What the specs on the wheels???

What exactly is the 27 mm socket for????

Did it solve the 3 amigos?