Discovery 2 WHEEL BEARING swap! - Step by step how to video

Рет қаралды 7,744

Күн бұрын

Land Rover Discovery 2 V8 and Td5 and Range Rover P38 wheel bearing / wheel hub change.
This is a step by step guide on how to do this job yourself!
If you have the three amigos it might be one of your wheel bearings or ABS-sensors.
Watch this to save a lot of money doing the job yourself!
Follow me on Instagram
@Td5Adventures
Td5Adventures

Пікірлер: 30

@CaponeIII Жыл бұрын

Very clear, both verbally and visually. Thanks for the helpful video. I'll be doing both sides this week with more confidence.

@Td5Adventures Жыл бұрын

Thanks for watching and good luck!👌🏼

@SurvivalRussia 2 жыл бұрын

I know this is an older upload, but I appreciate it a lot. This will come in handy changing hubs on my Range Rover. thank you for your time buddy!

@Td5Adventures 2 жыл бұрын

Thank you! Good luck, the P38 and D2 share the hubs so it should be a very similar job😊

@MrMaxEf 3 жыл бұрын

You don't have to undo caliper from carrier. You may just undo carrier with caliper together. Did last week)

@Td5Adventures 3 жыл бұрын

Ah, clever!!

@Ja518 3 ай бұрын

Very good video. Thank you

@DanielHeini 3 жыл бұрын

Great video and very well explained! You make me more and more keen to buy one of the Disco 2's I made a testdrive in the last weeks :-D And a compliment to the cameraman sometimes a little trouble with the autofocus but the closeup filming was excellent so you could see everything what is important for this job. Regards, Daniel

@Td5Adventures 3 жыл бұрын

Thank you!!! Yeah I was really happy my girlfriend could film the first half, so much better than with a tripod in the second half... Oh nice, you will find one soon😎

@johnwannable Жыл бұрын

Great video, thanks! About to tackle this along with ball joints as I didn't pass inspection here in the U.S. Need to buy a 32mm impact socket and a torque wrench that goes to 500!

@Td5Adventures Жыл бұрын

Oh god luck! There are hardware stores here in Sweden where you can rent certain tools, maybe you can rent a wrench or just calculate the length of your bar and your weight to get a torque spec😉

@slobodank76 3 жыл бұрын

Great video 👍

@Td5Adventures 3 жыл бұрын

Thank you!!

@jerryallen34 3 жыл бұрын

Great how to. Thank you

@Td5Adventures 2 жыл бұрын

Thank you for watching!

@APromProm 3 жыл бұрын

Thnx, Great video! I hope you didn’t forget to secure the 32mm locknut ;)

@Td5Adventures 3 жыл бұрын

Thanks!! No, it's fine, I have secured it 😊👌🏻

@MrMaxEf 3 жыл бұрын

I've got 36mm nut! Got to buy head

@sal1520 Жыл бұрын

What brand bearing hubs you got mate

@joekrakowiak9487 Жыл бұрын

Can you use a wheel hub for a Discovery 2 on a P38?

@Td5Adventures Жыл бұрын

Yes, from what I know the hubs are interchangeable!

@fraggle23 3 жыл бұрын

You don't need to take the abs sensor off, just leave it alone, especially as the new hubs all have them attached

@fraggle23 3 жыл бұрын

But good vid generally

@fraggle23 3 жыл бұрын

And any time you change a hub you should take the opportunity to change the axle seal

@Td5Adventures 2 жыл бұрын

Sorry for my slow reply... Yeah I should have bought an axle seal! The abs sensor does not need to come off, you're right. But in this case only the sensor was bad.

@andywood492 Жыл бұрын

How do I replace the wheel bearing if I don't want to replace the hub?

@Td5Adventures Жыл бұрын

You can't! It's a single unit all together.

@samuelbhagothiparsad3882 2 жыл бұрын

Its a wheel bearing hub. You did not replace the wheel bearing. You replaced the complete wheelbearing hub assembly. I say this cos I was told my wheel bearings were shot. walked into autozone, they ordered and sold me 4xwheelbearings and only found after stripping that I needed the complete hub assembly.

@Td5Adventures 2 жыл бұрын

The only way to replace the wheel bearing on these is to replace the whole hub. Your hub doesn't go bad, the bearing inside it does.