Lifetime 8' x 10' Outdoor Storage Shed | Lifetime Assembly Video

Рет қаралды 133,113

Күн бұрын

Пікірлер: 111

@LifetimeProductsAssembly 2 жыл бұрын

@WalterWhite-j7c Ай бұрын

I just finished assembling my Lifetime shed (#60295). This video was EXCELLENT; I hardly looked at the manual. It took me about 15 hours, spread over four days (evenings and part days on weekend) and I did it solo except for two instances where I had my wife push on a wall to line up the screw holes. The video made the jobs super easy, and I'm no handyman. I had only one issue: The screw holes on the left rear roof panel were off by 3/4 inch. Solution: I used the bottle jack from my 4Runner, placed it on a ladder (blocked up with a few 4x4 pieces of wood I had laying around) and lifted the left side of the rear truss until the holes aligned. I also had to pull the rear gable panel inward to get alignment, which I did by slipping a rope through the metal channel on the panel, pulling it back until the alignment was right, and then tied off the rope. This looks and feels like a quality, solid shed. Thanks Lifetime for an excellent assembly video!

@8877jazz Жыл бұрын

Tomorrow we're going to assemble our new Lifetime 8' x 10' outdoor storage shed. Thank you for the video.

@H3c171 10 ай бұрын

How's it coming along

@CharlieFlask Күн бұрын

For the cross member on the trusses, I put the bolt on the inside of the channel, held it with a wrench and used a screw gun to tighten it.. After all of the pre-assembly was done, it still took 4.5 hours to put it all together

@yogawolf2810 6 ай бұрын

Dude you made this look so easy, but thanks a bunch for the video

@henrymethorst9108 10 ай бұрын

just bought this today from Costco. Glad to see you have a detailed video.

@michaelp1979 2 жыл бұрын

Warning!!! Don’t use an impact drill unless you have a torque setting on it and you make it really low. Use a screw driver as you can feel the tension when you are tightening the screws.

@KingOfTheDungle Жыл бұрын

Skill issue, but thanks for the tip anyway.

@cdanielh128 2 жыл бұрын

Great video! Thanks much. Not all learn from reading. Being a visual learner this made the whole build pretty simple.

@KenjaajneK 2 жыл бұрын

not to mention the user manuals, at least the 8x15 i put together where an absolute mess... mixed translation issues, mislabeled parts needed undone and such... wow... and I see there are a umber of structural improvements as well... really glad they are upgrading and creating the user friendly videos too.

@HashiAkitaPuppy 2 жыл бұрын

Everything is much harder than in this video, the roof panels are so tight it the truss grooves, there's no way you can just slide them in like this.

@jeffcray2217 2 жыл бұрын

I put this exact shed today, wouldn't have been able to make it through without this video. Thank you for making it. Much appreciated

@hang4963 Жыл бұрын

Thank you so much Sir you are the master of Craftsman😂❤👍👍👍🤣

@sherrysvesnik7711 2 жыл бұрын

Looks like a very comprehensive video.

@berniewasserman265 2 жыл бұрын

Great video. A few improvements ñeeded on the shed itself. The snow lad kit should have all holes prefilled. Either using slf tapping screws or note and bolts. It is very difficult to drill the screws into the metal when no holes exist. The side window brackets do not clear the raised edge of the window so they will not install properly. Leveling the shed doors could be designed better if there was a opening in the front of the floor to allow the shims to get just under the bushing. A better idea would be to all the bushings height to be adjusted by leveling screw base like on a table. This can also be accessed through an opening on the front edge of the floor. Otherwise great product

@keithdouglas3586 Жыл бұрын

Building this today and I am frustrated as hell with the instructions. I just built a Keter shed and I am so impressed with their manual. Every piece is labeled but this shed has you guessing. When putting in the roof panels he should tell you there are little holes that need to be lined up. His pieces slid in effortlessly mine has me struggling like hell. The wall pieces have popped out at the bottom because of the thin plastic holding it in. One screw has popped out of the wall it’s so wobbly. Keter sheds are much more stronger this shed I fear will blow away from the base in a strong wind like Dorothy’s house in Wizard of OZ.

@ermamilspaugh Жыл бұрын

Funny analogy, I hope you don’t have to visit oz to find it 😂

@ozedude7082 2 ай бұрын

What can you expect? Its US made and they take great pride in producing sub standard crap. 🤣

@KenjaajneK 2 жыл бұрын

Really glad you made these videos... THANK YOU... I will be putting this one together next to a lifetime 8 x 15 ... the video make Way more since then the discombobulated user manual from the first other unit a number of years ago

@LifetimeProductsAssembly 2 жыл бұрын

We love a loyal Lifetime customer! Glad to hear this video will be helpful!

@KenjaajneK 2 жыл бұрын

@@LifetimeProductsAssembly with supply crunch the way it is... Wow... can't leave the customer service of Lifetime... the way they helped me acquire this new one pre-manufactured for locked in availability was Great!... Big Thanks ... Slab should be cured enough to build later this week :-)

@goawayplzthnx Жыл бұрын

@@KenjaajneK always nice to see a Lifetime Products sales rep in their own comments 😂

@KenjaajneK Жыл бұрын

@@goawayplzthnx other than it turned out to be crap, They mix matched new and old manufactured pieced for a build that wouldnt match up pieces ,,, texture and sizes where different and they only offer was to take it all apart and pay shipping for a replacement... complete crap so much extra work to build and seal

@goawayplzthnx Жыл бұрын

@@KenjaajneK oh no! I am sorry your experience was bad. Mine is, too.

@mtbridersanonymous9152 2 жыл бұрын

Just got done with my foundation, starting the shed today

@LifetimeProductsAssembly 2 жыл бұрын

Let us know how it goes! Can't wait to see the end product!

@misrakreta6896 2 жыл бұрын

Good Good job thank you very much.

@taka6281 2 жыл бұрын

Considering purchasing at Costco in Japan Is it okay to use W = 81.28cm vertically during transportation?

@jrobinson8841 Жыл бұрын

I have two of these sheds & would like to take one section out for the other. From what i can find the base on that smaller shed would need to be 90 inches deep is that right.

@ajueket 2 жыл бұрын

I appreciate the video very helpful to use in conjunction with the manual

@rubensilva6894 8 ай бұрын

gracias, me ayudó mucho el video, a la hora del armado... saludos

@reginarasmussen5085 2 жыл бұрын

What do you do when the last roof panel is off by about 3/4 of an inch? Everything else fit good until we went to put up the last roof panel by the gable at the end.

@andreasmith8052 9 ай бұрын

Exactly! A nightmare!

@dnegro Жыл бұрын

this guy knows its not that easy

@tstar72 2 жыл бұрын

Thank you for this video!🙌🏼

@ivettesantana4319 2 жыл бұрын

If it only was this easy lol. We have been at it 4.5 hours one day, today another 4 today and we are still not done but hopefully another 2 hours session on the roof and we are experienced DIY people.

@LifetimeProductsAssembly 2 жыл бұрын

Sorry to hear that this is taking you awhile. What parts exactly are you having troubles on?

@H3c171 10 ай бұрын

@@LifetimeProductsAssemblyI think they made it clear that the WHOLE THING is screwed up, build quality is shit and screams of "made in China". Source quality products to make your customers happy

@katherinesipe5962 8 ай бұрын

Having trouble screwing in the skylights without it popping up. Seems like they need to be held down from the top if the top of the roof. Tips? Also, the last piece of the roof (back piece without skylight doesn't seem to fit. Any thoughts a as to why?

@LifetimeProductsAssembly 8 ай бұрын

Give our customer service team a call and we can trouble shoot the issue with you and see if we can help figure out what's happening. They can be reached at 800-225-3865 or by email at customercare@lifetime.com. Customer Service hours are Monday-Friday, 7:00 am to 5:00 pm and Saturday, 9:00 am to 1:00 pm (MT).

@jonjanssen6523 2 жыл бұрын

Step 2.5 absolutely is not complete in the printed instructions. Good thing i caught this video before i mounted my roof panels.

@reppinjnf Жыл бұрын

My roof panel holes don't match up with the truss holes. I've got an entire one side on but the other side doesn't align.

@ddoubleyyou 11 ай бұрын

What'd you do end up doing

@H3c171 10 ай бұрын

Same, returning it today

@H3c171 10 ай бұрын

@@ddoubleyyouback to the store 😂

@rocketkid3787 Жыл бұрын

Could you leave a panel out and shorten the shed? Shorten length

@josesaltos9910 Жыл бұрын

Jose Saltos, very good instructions and easy to understand.

@ggolds5 2 жыл бұрын

CONFUSED with 10.5. What area is between the gabel and the truss????. Not sure where these bars go.

@LifetimeProductsAssembly 2 жыл бұрын

If you refer to your manual and this video, you will see two notches on the roof panel close to the gable entry and the start of the truss. You will need to insert the roof support in these notches.

@darthmillenium9486 8 ай бұрын

Hi there, does anybody knows whats the AIW piece for? Its a black rectangle

@LifetimeProductsAssembly 8 ай бұрын

Hello! That piece can be placed under the floor panels so that you can lock the tabs on the corner wall panels into place easier.

@hoeunghim4314 3 ай бұрын

Wow

@sunshinelizzy1 5 ай бұрын

Anyone knows how durable it is? Does it really live up to its name?

@vegetarko09 6 ай бұрын

My right door was bent at the bar. I got a new door but I am wondering if anyone or Lifetime have any suggestions to install it without taking off the roof at the doorway.

@LifetimeProductsAssembly 6 ай бұрын

Unfortunately, the only way to replace the door is to remove the gable and roof panel.

@jcruz0143 Жыл бұрын

Hi there, what the measurements of the floor?, I'm going to make a foundation to assemble my new storage shed.

@henrymethorst9108 10 ай бұрын

DId you find the answer to this? I just came home with mine.

@Xanadu245 8 ай бұрын

According to the instructions, the base (wood or concrete slab) should be 118 1/4” X 93 1/2”

@vasilecojan31 Жыл бұрын

What's the width of the open doors for a 8x10 shed? Thank you.

@LifetimeProductsAssembly Жыл бұрын

56" x 76"

@katyuuki2261 2 жыл бұрын

Out of curiosity, who was the artist of the song used? I’m hooked on itX

@mariethevenin2680 2 ай бұрын

How much for the sed 8x10

@omarjaber692 2 жыл бұрын

Is there a video for the 60056 model?

@LifetimeProductsAssembly 2 жыл бұрын

Unfortunately, we do not. However, you can use this video kzfaq.info/get/bejne/hs95ZbqEr66zcqM.html since it is essentially the same assembly as 60056. You would just have to refer to your manual for the door latch assembly.

@hornet7288 Жыл бұрын

What are the dimensions for the box this shed comes in?

@LifetimeProductsAssembly Жыл бұрын

Both boxes are 95” x 32” x 11”

@Alphagosney 10 ай бұрын

So how do you put the floor together???

@LifetimeProductsAssembly 10 ай бұрын

The floor assembly starts at 17:09. Lay an outer floor panel down, lift an inner floor panel at an angle, interlock the tabs, and then lay the inner panel down.

@dudesome6969 3 ай бұрын

Does it come with shelves, or where can they be purchased? (Canada)

@LifetimeProductsAssembly 3 ай бұрын

It does come with a 90x9 inch shelf

@tiremelter 2 жыл бұрын

Just built a lifetime 8x10 but your shed must not be made of cheese like mine seamed to be... No way i could tighten the screws that aggressive without the feeling every screw was gonna strip

@bizo2pg31 Жыл бұрын

You need to use a low torque setting.

@censorshipsucks9493 Жыл бұрын

You need the video AND the manual. Sometimes the video is wrong, and it's not about accessories. It's just wrong. Case in point I have model 60325, and this guy is telling me to put the hardware on backwards from the manual.

@LifetimeProductsAssembly Жыл бұрын

This issue could be that 60352 is quite different from this model. Meaning you may see different hardware and/or accessories being used. But, you are correct where it is very beneficial to have the manual available during the build!

@censorshipsucks9493 Жыл бұрын

@@LifetimeProductsAssembly God forbid you have a video for the correct model. As I said in another post you guys just don't want to show someone wrecking a rubber mallet, and banging away for 15 minutes to "slide" the bars in.

@H3c171 10 ай бұрын

That's what you get for buying cheap, buy nice or buy TWICE

@censorshipsucks9493 10 ай бұрын

@@H3c171 Sorry I'm not made out of money, and can't afford a $5 K shed from our local shed company.

@seanconnolly3274 Жыл бұрын

Very helpful, but I would emphasize to people up front that this is for the 8x10" shed and that the 10x8' shed has a DIFFERENT video. I spent 20 minutes watching this video before realizing the issue and noticed some things didn't make sense.

@LifetimeProductsAssembly Жыл бұрын

Thanks for the recommendation. We ask all customers in the beginning of the video to check to see if their model number is the description box to make sure this video works for them. We also add the description of the shed in the description box as well as the thumbnail.

@ojcomputer 2 жыл бұрын

Did anyone here use gravel or rock to support the foundation, or did you just put it directly onto the dirt/grass?

@LifetimeProductsAssembly 2 жыл бұрын

We recommend only using a leveled cement or wooden platform. This will help your shed stay the most secured and will help during the assembly process with the lining up everything into place.

@zoliver86 Жыл бұрын

I'm using dirt, gravel and a wood

@elisebailey6881 Жыл бұрын

I built a wood base of treated 2x4’s with treated plywood on top. I levelled the ground below by digging down not building up. I also closed in all gaps in the sides of the base so I don’t get rats or anything living under it.

@mariethevenin2680 2 ай бұрын

How much is it 8x10

@LifetimeProductsAssembly 2 ай бұрын

The price for an 8' x 10' shed varies between about $1499.99 and $1899.99, depending on the model number. Here is the link to our medium sheds so you can take a look- www.lifetime.com/medium-sheds.

@ct4529 Жыл бұрын

The video was great and I watched before I purchased my shed. However, I found it disappointing in that it shows the parts of the snow load kit as if it is included as part of the shed. It also shows hooks being included. The parts (identified from the website) of the snow load kit was not included and neither were the hooks. I see this as a bait and switch tactic. 😞

@LifetimeProductsAssembly Жыл бұрын

What is your model number you purchased? Depending on your model number, accessories do vary.

@elidatorres8039 Жыл бұрын

No se ve como armar esa casa

@jk6628 2 жыл бұрын

what color is it

@1ds2ds3ds 2 жыл бұрын

What Brand is it? What size is it? How much is it? Look it up on google clearly tells you. Why have a company sit there and answer previously answered questions? Go waste someone else time with this nonsense question! Also I hope you have a miserable 2022 year and that your hair falls out

@martyramirez1546 2 жыл бұрын

@@1ds2ds3ds Haha!

@1ds2ds3ds 2 жыл бұрын

@@martyramirez1546 :D

@elisebailey6881 Жыл бұрын

I’m sorry but this was 50% useless. Let’s start with roof support bars! At no point does it tell you which notch to put the roof support in, there are two and is the other one just for looks? One end has a hole in it as well which makes zero sense as no screws go in it and there is no mention as to what end which goes! The tiny little screws to hold the floor together are pretty much useless. I swear if IKEA had these there would be better instructions.

@stephaniehenry5617 Жыл бұрын

I just opened my box I have no hardware .

@LifetimeProductsAssembly Жыл бұрын

Sorry to hear this! Reach out to our customer service team so they’re able to get you your missing parts. They can be reached by phone at +1 (800) 242-3865 or by email at customercare@lifetime.com

@stephaniehenry5617 Жыл бұрын

@@LifetimeProductsAssembly thank you

@LeNguyen-wj9og Жыл бұрын

How to build by yourself...? No helper ...!

@LifetimeProductsAssembly Жыл бұрын

You would build it the same way. Just keep in mind, the extra helper is extremely essential to help get all the parts in place.

@stevenwoodcock8702 2 жыл бұрын

Only reason they made this video is because the instruction manual that comes with the kit is useless. Any halfway smart person can watch this video and put the shed together with no prob. Take the same person and try it with the directions 😂😂😂😂😂

@dalewhite3914 10 ай бұрын

This video can kiss my butt. Spent twelve hours on it. And still didn't finish it. None of the plastic lined up anywhere.

@user-wj9pr3re3s 5 ай бұрын

Model #60441u

@LifetimeProductsAssembly 5 ай бұрын

There are a few small differences, but this video is the closest to model 60441: kzfaq.info/get/bejne/gdCJf7Ry2MeVpH0.html

@H3c171 10 ай бұрын

My instruction manual numbers go from 6,7,8,11,10,9,12 What a joke, this vid isn't helpful as well the whole product is garbage, DO NOT BUY

@Logan-ix8vh Жыл бұрын

Warning they have all their crap mixed in packing and missing pieces… don’t buy this junk was a headache putting together. And cheaply built

@H3c171 10 ай бұрын

Made in China shed

@jefftobey5826 3 ай бұрын

this shed is a piece of crap, gable roof panel dosen't line up at all on the corners, everything is level and straight, this shed would not last in a 40 to 50 mph wind either that we have here, have spent two days fighting with the coners to make the roof panels fit, still not working, NEVER AGAIN !

@LifetimeProductsAssembly 3 ай бұрын

We apologize about the frustration with the assembly of your new shed. What type of foundation is your shed built on? That could be causing the difficulties. Try watching this video on how to align your roof panels- kzfaq.info/get/bejne/n7eJptWSmMvMpKc.htmlsi=qptvvpzaxJnvzPpK. If that doesn't work, give our customer service team a call and we can troubleshoot the issue with you and see if we can figure out what is happening. They can be reached at 800-225-3865 or by email at customercare@lifetime.com. Customer service hours are Monday-Friday, 7:00 am to 5:00 pm (MT).

@jefftobey5826 3 ай бұрын

@@LifetimeProductsAssembly i built a 12'x12' wood platform, and it's all level, and a strong platform, i have taken off all the roof panels and squared up the shed, and reput on the roof panels and still won't line up, have no idea, and i am an expericed craftsman

@neilwalker4277 26 күн бұрын

This video is a complete joke and either heavily edited or using doctored parts. The parts just don't go together like he's doing it. For example simply sliding the metal into the door frame. Even after wd40, especially the round tube does not go in, they require lube, brute force, wiggling and banging. The manual has wrong parts listed, doesnt mention orientation of most parts. But the worst thing is you need 4 feet of space on both sides to slide the roof on, so your corner spot is no use. They could easily have made the roof slot in from the inside or even outside by clipping them in to the metal frames, but just bad design or money saving stops this.