And after watching this video with no explanation, the many who didn't know the secret to welding aluminium STILL don't know the secret to welding aluminium.

My Dad taught me to weld steel with an oxy-acetylene torch and a small tip and use a wire coat-hanger with the paint sanded off. Then, an old shop teacher of mine, taught me to pre-heat the aluminum before welding it. He said to put a piece of Stainless Steel in behind the hole you were filling up, in your aluminum welding project, and melt the side walls of the casting while you melt in broken strips of CASTING, instead of aluminum rods. The metals HAD TO match, in order to melt together and not break again. The aluminum would run on the Stainless Steel plate, but wouldn't bond to it, so you would have a smooth surface on both sides of the aluminum patch. You didn't have to worry so much about it "falling out the back," since you had a backing plate it wouldn't melt to. Bill, from Tn. 🇺🇸

That cutter on the angle grinder has to be up there with a chainsaw angle grinder cutter as the most dangerous power hand tool attachments on KZfaq.

"Kuli? I want you to know? This was a professional Job you did. You are an Engineer(A Doctor Welder.). Some people may look at this job as not important or simple, but? It was very serious to complete. Your work is highly respected."👍

No tricks involved. It just time, patience and more than an afternoon of experience and trust in ones own abilities. Well done!

Was the first aluminium welding I had to learn as an apprentice 25 years ago not as easy as it looks to much heat and poof it just falls away.

الله ينور عليك انا اتعلمت منك حجات كتير جزاك الله خير

My brother had a case with a bad crack. It was a Yamaha as well and his friend, some kind of exceptional welder, touched it with. A grinder and said that's why nobody wants to mess with it. It's magnesium. I need some special rods so it'll take a couple days because I have to order them. Impossible to tell where it was repaired.

Индусьі давно паяют алюминий автогеном и не парятся а мьі аргон спец єлектродьі

Поинтересуйтесь, как скоро оно отвалится. Есть более простые и надежные методы пайки, но - с помощью реактивных флюсов и при температуре около 280 градусов. Проверено сотню раз.

Thank you very much! I’ve wondered what to use my oxeacetine for!

from wa.state here. i had to do that to my bike in the 70s. nice work.

Well done! Btw is this exciter/sniper 150 v1?

I’ve got a tiny crack on a cylinder head (sweats coolant) crack is about half of an eye lash, what rods are those?

So, how warped was the case when you were done?

Do you explain what welding rod you can aluminum rod?

Не понемаю что за присадки.здоровья и всех благ

En que momento estás soldando??! Yo solo veo un relleno

Hobart makes Aluminum arc weld rods. I used them a few times fixed stuff. Electrode positive around 120 amps it jumps onto part .

5:35 great way of losing your fingers or hand!

very Nice work 👍

❤ Озвучку добавите ??

Interesting! I have tried before to weld with propane and found it didn't have the same properties as acetylene! I found that propane seemed to give a larger area of heat making it difficult to use but as I see here it looks workable. This was years ago and I was younger like 25 years or so. I brought the part to someone else and they used acetylene So I figured propane was not viable. Thanks I shall try again.

ficou top, mas uma bola bem feita de durepox resolveria tbm.

Bang kenapa setiap aku mencoba pengelasan alumunium selalu melorot ya?

لم يستعمل العامل المساعد وهو زيتي

Vraiment une Grande BRAVO

Pengelasan yang jenius luar biasa mantao

Может это эфективно но не просто.

As u get better at welding you will sharpen your tungsten less and less. Your skill will improve that you always keep a perfect gap without touching the material with the electrode. One more critical safety advice for welding in a confined space dont smoke weed before u weld in the confined space.

With coat hanger ? What's this guy using to weld with 1711 stick welds

I watched this comment and showed it to my neighbour. He said that it seemed familiar, so we rented a projector and read it with the entire town and we where astonished, when we found out how original and funny it was, before it actually was copy/pasted from millions and millions before this.

Paying someone to do this would cost 10 times more than just buying a new case cover.

Era tão mais fácil tampar o buraco com um pedaço do mesmo material e soldar já fiz vários

Why so many different rods and what are each made out of? Obviously, some are a low melting point alloy that can be melted on top and spread over smoothly. This being a low stress part and not important in terms of safety, I'd trust this repair, but, if available, a factory or used replacement from a wrecked bike would be so much more cost effective in terms of shop time and cost to a customer.

Nice. This is a metal artist

Extraordinário 👍👍👍

Think you will find he is using special brazing rods. You see this at classic car shows and they make it look easy. Its brazing not welding. Need to have the correct torch to concentrate the heat.

Good job!!

Show de bola parabéns

Good job

Basta mo lang ininangan wala paliwanag! Kung ano mga klase rod ang mga ginamit mo at materyales

Хоть бы сальника вынял

Not sure if that’s technically considered welding, it’s probably more accurate to call it brazing and here’s why. Welding especially Oxy Acetylene Welding true Welding uses bare filler metal where Brazing uses Filler Metal that has a flux cored center or a flux coating or even possibly a jar of paste flux in rare instances. At the start of the process he was holding rods that looked almost like Stick Welding Electrodes and that is what he used to make his first pass around the original parent metal because it has a flux and then he used scrap aluminum that looks like he melted out into his own filler metal rods very crudely formed but they worked and he kept switching between the fluxed rods and then the bare scrap aluminum then back to the flux rods then bare aluminum then fluxed ones. So what he did was a suitable solution if he lacked access to a Tig Welder but that is how it truly should have been repaired but it requires access to the equipment and skills beyond the average welder skills

Вы используете обычную алюминиевую проволку и разглаживаете потом электродом?

I'd like to do this just to see, I think it will take patience.

Ikut menonton dri ASIA WELDER

Le hace falta un polvo limpiador y solvente porque el aluminio es muy poroso a no ser que el aporte lo tenga incluido

Now replace the seal you burned up.

Before welding aluminum, I used to use charcoal on an electric welding machine

I like this trick 🎉

The welding electrode is made of which metal .? Any code name. ?

Это - космос!

Guys can someone tell me,can you weld it with map gas?

Практически как новенькая, осталось только покрасить 😉👍🏻

Bon travail

ガス溶接がやり易いのか🤔

Профессионально! Пропан с кислородом или ацетилен?

Me gustaría que también dijeran el proceso y los materiales que usan , porque así como pudo decidir si es cierto o nadamas son videos falsos , si no puedo decirles que e gusto solo por ver lo que.hacen con mucha tecnología pueden hacerlo fácil ustedes pero los que los vemos no lo creemos al menos yo ya que e intentado hacerlo y el aluminio al calentarlo así como lo hicieron ,para mi se derritió y no se soldo , no engañen a los usuarios que los ven ,sean realmente sinceros y si no , no le veo el caso de que según enseñen y solo engañen, sean realistas , no culeros

That is not welding, it's brazing technic..either it is bronze (copper or aluminum)

Ah ganyan lang pala 👍

Bro just knitted that thing back together

Viele Menschen könnten auch mit deinem "Geheimnis" etwas anfangen.

I thought you had to tig aluminum but time will tell what works.

Rapi telaten

Justamente por eso era secreto porque mucha gente no lo conocía

А можно было положить в пещаную форму разогретую деталь и залить расплавленный алюминий?

Ça doit coûter moins cher de changer carrément le carter !?

Elpiji mean LPG in Indonesia language.

if u could only tell us the secret !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Скажи пожалуйста, ты осьминог? 5:36. Ведь точно запасные щупальца есть?

А что не показал как шнурки завязывал перед выходом из дома

Хорошо что у меня есть такой мастер

Unfortunately the secret is while it may seem possible it generally doesn’t last and definitely not with any process other than TIG

5:38¿Se puede ser más irresponsable?

This guy really needs to stop dropping his bike

Sambil Ngomong Dong mas Biar Netizen Faham

Enakan dalemnya dikasih mal tanah liat dlu om

Excellent job, well done, you the man.

bolt it to a piece of metal so ya dont warp the face any.

Looks like ur stater case broke

Обычная на пайка алюминия 😂😂😂

Yo me ahorro tiempo y compro la tapa mejor.

Keren

Спасибо, конечно, но мы уж по старинке, аргончиком🙂

Bagus

Skillful, extraordinary work

Yan,ang,hinaha nap,ko,ok

Telaten 👍

I can weld enough to safe my self

All cases, covers and clutch baskets are not made of aluminum. They are in fact made of Magnesium. You are lucky to get Aluminum to even stick to it also. Lol

THE NGELAZZZ

Hadeeeuh,,,

Красили бы...

うーん、まぁ応急処置というか、DIYとしてならって感じですが… 残念ですが…

Silver rod welding better isnt it ..😂😂

Preciso fazer no câmbio fiat faire kkk salve Alexandre de Moraes kkkkk

Sarà sempre un punto debola di rottura.

Many people don't need to know.

This is called brazing. And you wasted oxy acetylene to do it.