Abandoned Yanmar Tractor WILL IT START? Part 6: Transmission Seals

Рет қаралды 11,991

Күн бұрын

We need to completely reseal the transmission on the abandoned Yanmar tractor project. This tractor transmission has many leaking gaskets and oil seals. We need to split the tractor to check the clutch, and brakes too. This tractor is never going to leak oil again! TOOLS BELOW ↓↓↓↓
➤ Previous Video: Abandoned Yanmar Tractor Rebuild Part 5: Wiring: • Abandoned Yanmar Tract...
➤ Next Part: Abandoned Yanmar Tractor Rebuild Part 7: Engine Rebuild: • Abandoned Yanmar Tract...
Timestamps:
0:00 Intro
0:25 Drain Oil
1:29 PTO Seals
4:26 3 Point Hitch Removal
4:52 Making New Gaskets
6:00 Diesel Gearcase Flush
6:19 Shifter Removal
6:58 3 Point Hitch Lift Cylinder
7:32 Axle Gaskets
11:13 PTO Cover Installation
12:07 Axle Seals
13:04 Brake Inspection
13:11 Split Tractor & Clutch Inspection
14:37 Fresh Oil
15:00 Outro
Ingersoll Rand Air Tools:
● Impact Wrench: amzn.to/3H4Yzc2
● Air Ratchet: amzn.to/35xJYZW
● Die Grinder: amzn.to/3rYt6nD
Other Tools:
● Click Torque Wrench: amzn.to/3vG0UZ2
● Beam Torque Wrench: amzn.to/3INZwaB
● Metric Socket Set: amzn.to/3MsoApx
● High-Flow Air Fittings: amzn.to/2J0PofR
● Impact Protective Boot: amzn.to/33xQ7Ex
● Gasket Scraper: amzn.to/2YMR8q2
● Gasket Removing Pads: amzn.to/34hFVjU
Supplies:
● Tractor Transmission Oil: amzn.to/3tzsep7
● Felpro Gasket Paper: amzn.to/3D7tDGW
Seal Sizes:
● Wheel Seals: H55x75x9TC
● PTO Seals: H35x55x11TC
This is a Yanmar YM2000B diesel tractor.
As an Amazon Associate I earn from qualifying purchases.
#restoration #willitrun #yanmar #willitstart #automotive #mechanic #tractor #tractors #farm

Пікірлер: 45

@MattsShop 2 жыл бұрын

Hey Yall! She's almost done! Tools used in description. Timestamps: 0:00 Intro 0:25 Drain Oil 1:29 PTO Seals 4:26 3 Point Hitch Removal 4:52 Making New Gaskets 6:00 Diesel Gearcase Flush 6:19 Shifter Removal 6:58 3 Point Hitch Lift Cylinder 7:32 Axle Gaskets 11:13 PTO Cover Installation 12:07 Axle Seals 13:04 Brake Inspection 13:11 Split Tractor & Clutch Inspection 14:37 Fresh Oil 15:00 Outro

@alanjohnson4196 7 күн бұрын

Bravo making a gasket I was taught as a young lad. Use a ball peen hammer. Back side of head round. Cuts the fastener holes all pretty. Save the carpenters hammer for building a shed.

@MattsShop 7 күн бұрын

Thanks man. Yea I just grab whatever hammer I can reach at the time. I need to use the ball peen more.

@amossnowdaharleyman9179 Жыл бұрын

I've had 6 Yanmars over the years. Fixed and flipped 4 and kept 2. One of the flips was a Yanmar 3000 that I did an inframe on. Still kicking myself for selling that one. Made good money but it was a heck of a tractor. I'll go kick myself some more now.

@MattsShop Жыл бұрын

That's awesome. These things used to be a lot cheaper. What was the best model you had? Lol

@amossnowdaharleyman9179 Жыл бұрын

@@MattsShop At my shop building I use a 2310 as a dedicated spray tractor to only spray herbicide to keep grass killed in the lot. Just painted it (see videos). My favorite was the Yanmar 3000 I sold after fixing it. Big enough for a 2 acre truck patch,small enough to reach diversion valve on a 50 gallon 3pt sprayer from the seat.But my JD 1250 (built by Yanmar in the 1980's) is one of my go to tractors. Never has let me down and will pull a 6' bush hog in thick stuff 6' tall. Had a JD 1050 that was another fix and flip (paid 3000.00 sold for 4200.00 with nothing but fluid changes and a 200.00 top): used it to pull a JD 2 bottom plow,5'disc,1 row planter,etc. And yup,they use to be A LOT cheaper. Picked up the 2310 for 800.00 according to my wife,who is next to me. JD 1250 was bought at same auction on same day: $1200.00 for it if my memory is right. Been more than a couple of years ago but I think less than 8 or 9.I'm always on the lookout for Yanmars at a good price. Love 'em. Fixed and flipped 50+ tractors,dozers,backhoes etc last 20 years or so. Profitable hobby and a cash business.....

@jimbop101 2 жыл бұрын

Yeah Boy, Good stuff Matt, engine rebuild is gonna help me put my 1601D back on the farm.

@MattsShop 2 жыл бұрын

Yea, I have a badass rebuild video coming.

@yuttagarnsri6172 2 жыл бұрын

Hi l from Thailand my tractor yanmar 1900 need to repair like this . Thank knowledge

@bigkat1919 2 жыл бұрын

Dude been here since the beginning. Stoked to see your hard work and dedication to this project

@MattsShop 2 жыл бұрын

Thanks man! I really appreciate the support.

@natevanlandingham1945 2 жыл бұрын

I wish your videos were up 8-10 years ago when I did all this. I read and learned on my own with forums and the manual. I did writing posts on it on TBN yanmar forum. Also filmed some of it but I am lazy and hate computer stuff and didn't ever do anything with it.

@brittmrmanly4982 2 жыл бұрын

Great video Matt! I was lucky with my Yanmar 1700, the transmission screen was dirty and the fluid was dark but there was no water to be found. I need to replace the shifter plate gasket cause it leaks. . If I every have to pull the transmission apart, I have your video to reference! Top tip time. If you use the ball end of a ballpeen hammer, can punch out the gasket holes with it. Just lay the gasket on the cover and gently tap around the holes with the ball end. Hope this helps. Keep the vids coming!

@MattsShop 2 жыл бұрын

Nice! You did get lucky. Water sat mixed in this transmission for a while, but It didn't really damage anything. Yes, use this video to help. I bet this oil is over 10 years old. I know, it works better with a ball peen hammer.

@brittmrmanly4982 2 жыл бұрын

@@MattsShop I'm looking forward to the engine rebuild video. My tractor uses gobs of oil and I'm getting combustion gases in the coolant. Here's hoping its just a blown head gasket rather than a cracked head. Again thanks for the awesome vids!

@warrenosborne6044 Жыл бұрын

I have a YM 165 with a stripped out clutch shaft. Hoye didn't have one. Still looking. Meanwhile I got a YM 1600 in ok shape. This is invaluable information. Thanx man!

@MattsShop Жыл бұрын

If they don't have the shaft I'd keep an eye on eBay. You're welcome!

@brngrofdeth 2 жыл бұрын

Excellent and thorough job! Love and blessings from Ontario Canada!

@MattsShop 2 жыл бұрын

Thanks!

@adinko7 Жыл бұрын

Nice videos, 10:35 push the ball bearings in with the outer edge so you don't damage the balls in the ball bearing.

@UnkyJofus 2 жыл бұрын

I've got a 2220D, looks a lot like yours. 3 cylinder diesel, 4wd. Hoye Tractor has even great for parts.

@MattsShop 2 жыл бұрын

Nice. Does it run well?

@natevanlandingham1945 2 жыл бұрын

I just used RTV on those PTO rear assembly and the top 3pt assembly part of the case when I did mine. Easier and way quicker. Tolerances are not critical.

@natevanlandingham1945 2 жыл бұрын

You can get away with metric or standard o rings in some places but Yanmar used Japanese spec orings that are harder to find. Critical orings need to be proper ones if they hold lots of pressure.

@natevanlandingham1945 2 жыл бұрын

I didn't see you engage the PTO selector with the gears on the assembly, and maybe it's different than the ym2000, but there is an arm you have to reach in and engage with the sliding part of the assembly that selects PTO speed. I saw you pry that nut and shaft out but that's not the same and maybe it's different?

@barryharrissz4748 Жыл бұрын

I am having trouble getting PTO shifter right so I can slide PTO assembly back in 😟

@hrfch3352 Жыл бұрын

Por el video aprendo a desarmar mi yanmar 1050. Ya todo esta andando. Solamente la parte hidráulica lo q no retiene la carga.

@wnwanted94 Жыл бұрын

I cannot get my PTO cover off for shit. You make it look so damn easy at 2:20. All the bolts and nuts are off, PTO selector is off but it doesn’t budge. Hammer, 4 foot prybar this thing doesn’t move.

@wnwanted94 Жыл бұрын

I figured it out, had to make a special tool lol.

@AmsterdamCesar 2 жыл бұрын

Great vid Matt! Keep on going! Peeeeaaaacccceeee ✌

@MattsShop 2 жыл бұрын

Thanks I will. Peeeeeeaaaaaccceeee✌

@christophergallagher531 Жыл бұрын

About now, I'm wondering what duty this tractor will get. My 2020D is amazingly fuel efficient. Bet that 2cyl and 2wd unit will simply sip fuel! Here ya have me goated me into a trans flush, come spring. Thanks. Yeah, unless that hammer is an old friend, try a ball pean, for gaskets.

@MattsShop Жыл бұрын

I have used it a lot at this point. It uses next to no fuel. Runs for hours on a cup worth of diesel. I was impressed!

@snowman91700 2 жыл бұрын

Anytime you use a paper gasket you want to use Aviation sealer on it it will stop any bleed through the gasket

@MattsShop 2 жыл бұрын

Yes, I do 90% of the time unless it will make a mess and clog passages up. Good stuff.

@tomkergil3304 2 жыл бұрын

Very good work. Your words would indicate you were not certain about what construction you would find. Did you have exploded diagrams to review or just powered through the rebuild?

@denysseptian6240 Жыл бұрын

Hi matt, whats part number of rotary seal?can it fit with yanmar hand tractor? Im struggle to find it

@MattsShop Жыл бұрын

Which seal are you looking for? The PTO shaft seal?

@denysseptian6240 Жыл бұрын

Yap pto seal and rear axle seal

@MattsShop Жыл бұрын

www.hoyetractor.com/CTGY/2000TRANSINT.htm Checkout #44, #69, and #70. You need 2 axle seals per side. This is for a Yanmar YM2000B.

@Jeremy1awesome 2 жыл бұрын

I drive a 06 Chevy classic my power window won’t work either side

@natevanlandingham1945 2 жыл бұрын

Most all that water comes from around that shifter boot....most of that work was in necessary., Makes good content though.

@paocha9332 2 жыл бұрын

hello matt, where are you located?

@MattsShop 2 жыл бұрын

USA Why?

@paocha9332 2 жыл бұрын

well, i had a 1610d yanmar that need to be fixed and i saw you show a very good work on youtube so want to know where you at and what state you are at so i can bring my tractor to you to do some service for me