MD2020 fuel injector check part 2/2

MD2020 fuel injector check part 2/2 - assembly

Рет қаралды 11,693

4 жыл бұрын

It is pretty easy to remove the injectors and get them checked, but a bit more difficult to install them again.
Under the injectors you have a insert and under that insert there is a copper ring, and the whole thing is of course stuck pretty well so quite a job to remove without a special tool.
I then bought a internal bearring remover in the correct size, but then there was a new problem.
You also need new copper washers and have to tighten the injectors with a torque wrench.
Tools and parts I used :
3580631 - 3 pcs. gasket between injector and return line - 37 USD
3580077 - 3 pcs. gasket under the injector - 17 USD
3580075 - 3 pcs. gasket under the insert - 24 USD
Loctite 574 (fluid gasket) - 38 US Dollars
Beta torque wrench model 606/10 3/8" 20-100 Nm. - 208 USD
Jackhammer (slide hammer) and special tool - 72 USD
Nozzle check and ultrasound cleaning - 73 USD

Пікірлер: 29

@raybelcher 6 ай бұрын

Thank you very much for your video. I wish you the best for 2024.

@conallocuinn407 Жыл бұрын

Excellent photography and commentary. Thank you.

@victoriastreet8919 11 ай бұрын

Excellent work. This low pressure fuel system has continuous self-bleeding. This circulates fuel via the return piping back to the tank. It keeps of air from affecting the injection pump but not if its a large quantity of air. You can manually pump much fuel/air through this circuit. Very little fuel goes from the injectors into this circuit for mechanical injection (the Brits call this Leak-off).

@SailingAurora 4 жыл бұрын

Nice video Tino, a bearing puller is definitely a good tool to have, I find I always need more tools and sometimes I get pretty frustrated when I need to order more to get the job done. Patience is the key. Cheers

@twiper 4 жыл бұрын

Thanks :) And yes I also ordered parts multiple times for my injector project, have also done a lot of research to be sure I have done it right. The point with the project was also to learn about the engine and how it is build and why.

@alekseimuzychenko1701 3 жыл бұрын

Great videos. Thank you for your work, I can imagine how long it takes. It's a pity I didn't see these videos when I first got into the fuel system of my MD2020 I join in the request to include English subtitles. It seems to me that this can be done simply in the video settings, nothing needs to be altered.

@ulrichkrenn3649 3 жыл бұрын

Hello! Nice Video! Thanks!

@pavloskourris277 Жыл бұрын

Thank you for your video. Really thorough and very informative. My 20-30 is burning a lot of fuel (white smoke). Took my injectors for service and ordered the 4 parts (2 gaskets, heat shield, insert) (you have 3 on your 20-20). Hope my mechanic has the extractor as some gaskets, heat shield and insert are still in the engine. Also did a compression, 1 was 17 BAR another 18 BAR while the middle one only managed 2 BAR. As my engine was sitting for a few years my mechanic is hopeful that the low compression on middle piston is some carbon residue on the valves or a piston ring that got stuck and that after inserting the serviced injectors things will go back to normal, Your opinion and insights on this point is highly appreciated. Thank you once again.

@twiper Жыл бұрын

To loosen up the pistonring a known trick is to fill in a bit of automatic transmission fluid into the cylinder and let it sit for some days. An alternative is to buy a additive for the oil, you can get a compression enhancer additive wich also loosens up the piston rings. If you don't see any improvements I think it's the valve or in worst case a broken piston ring.

@pavloskourris277 Жыл бұрын

@@twiper Thank you, will try your suggestion

@onurertug9070 4 жыл бұрын

thank you so much ) Teşekkür ederim. Sevgilerimle )

@srenbentsen950 9 ай бұрын

Hi Tino. Hvor købte du inserts til dysserne og værktøjet til at få dem op?

@toscatara 2 жыл бұрын

Thank you very much in advance I've really searched and I can't find anything

@toscatara 2 жыл бұрын

Hello Can you help me identify that part? I have small leaks that stain the silentblock

@steegzor5161 4 жыл бұрын

Great video thanks a lot! But do you really need to change the insert as well? For my D1-30f it does not state that in the service manual.

@twiper 4 жыл бұрын

You must only change the copper gaskets and re use the old inserts.

@steegzor5161 4 жыл бұрын

@@twiper wow quick response thanks🙂 but i think i just found out my engine does not have the insert. Can that be the case?

@twiper 4 жыл бұрын

@@steegzor5161 Yes your engine has only a copper gasket in the bottom and one in the top of the injector, so a bit more easy to do the job.

@steegzor5161 4 жыл бұрын

@@twiper ah very good. This weekend i am doing the whole service with valves and everything for the first time myself and you help a lot! You are pretty much the only one who makes this detailed videos on volvo penta.

@tamar5261 3 жыл бұрын

Hi I have the 2030, when I took the injectors out the inserts were stuck on the end, so all I have to do is change the little copper washers in the head, is this right?

@CH_1966 4 жыл бұрын

how many hours on your engine?

@twiper 4 жыл бұрын

800 hours.

@CH_1966 4 жыл бұрын

@@twiper That was early for that overhaul.

@twiper 4 жыл бұрын

@@CH_1966 According to the manual it must be done every 400 hours, the boat is 16 years old so I thought it was time.

@AngelGonzalez-rz5ub Жыл бұрын

Hola me puedes enviar el enlace de la herramienta de extracción?

@twiper Жыл бұрын

www.ebay.com/itm/142928501404?epid=16023413509&hash=item214733da9c:g:sqgAAOSw7vxbkDLF&amdata=enc%3AAQAIAAAA8JXSGh16PDZm1Ug4EU8bBKhsdS6WZk6ymtiqt408SgCaVZ4IF7vu8OTkJnyymDlMfQ42%2FuYUKd9EKEqhg0Agqi5AAFAKPqkLq9pPjW6IdSeuxOUa7jGYjW53%2Fjih%2BGnSnZcM%2Fp1xPXi%2FSyT5e%2FV%2F9etwXEolhheR7Oo%2BzYDfFXo4CNjBowMdagyykwqbcceASUtflauNWysekgyTO1YUfhgzQUIo0pGWqHGr3eWYX0ZZTDaOCUn4CsHgXIkjh8wtNp94vhPNpNe%2FvY6rExqAEa8mhFZMjPrGPZ4AnfsDY2hro%2BefJhpgMFheRFrSkA%2B1jA%3D%3D%7Ctkp%3ABFBM5s3ngZxi

@cenkandic 3 жыл бұрын

We want English subtitles.

@owsivictor 2 жыл бұрын

@adamo35se 2 жыл бұрын

Hej, upptäckte fel vid din montage av spridare 9:43. Koppar brickan(3580075) ska vara monterad på insats ringen (3580076) och efter monteras i motor. Koppar brickan ska inte ligga ovanpå ringen som är faktum i din video.