You did a great job on the process of the install.

You, sir, are a true professional. Very well done!

awesome video, no bs, simple but thorough.. keep up the great work!

Great job and video! Thanks for posting this.

Bloody good video mate. Cheers for that

Thanks , you answered all my questions right there 👍👍🇺🇸

Thanks for this video. Just installed my trolling motor today following these instructions. It went pretty smooth for a first time.

Very helpful video, thank you!

Nice job!

Thanks for sharing! I have a Robalo, the location of those batteries is in a wet location. If being used in the salt, please cover those terminals in Dielectric Grease or a NCP2 type product. Or try to cover or move water away. Do what you can to extend the life of those expensive batteries!

Great job explaining 👍👍👍👍👍✌️

Really good tutorial for me and I also have a Robalo

This will look really nice for my Sea Fox Commander ❤️❤️

Great instructions I always use a lock washer I addition to the nylon lock nut as you can’t make this connection to secure trolling motors take a lot of beating on the bow

*Great little trolling motor **enjoyable.fishing** recommend had it hooked up to my 15 foot old town canoe and it pushed it pretty good with me and my son (220 pounds each).*

Great job, thanks.

Two years later this motor is going strong kzfaq.infoUgkxBZWgzfpS2Jj7JqIHyaSZjyVHNUgCKCBf Just uploaded a video of it after 2 years. We use it probably a dozen days each year on our small raft.-original review- We got this motor the other day and tested it out. I don't have anything to compare it to, but it seems good to me. It has all the features advertised - the motor housing is metal. We will see how it performs longer term and I will revise this review if needed. Some initial observations:- Good thrust, moves our boat around really well- It comes with a circuit breaker but no switch - so there's no way to kill the motor other than yanking the connection off the battery. I installed an inline switch.- The mount bracket is plastic and I worry it might break- There are a number of plastic parts that I worry about, but the most important ones are metal or some kind of composite

excellent video

Great video bro. thanks.

Great video. Muchas Gracias.

Thank you.

Awesome…thank you…

Upgraded from my 30# MK that maxed out at 3mph. This pushes my pelican pwr 100 at 4.5mph which is nuts since the pwr is a slow yak

Hey Chris, excellent video. I love the location for your heading sensor in the head. The spec recommends to not locate it within 24" of any power wiring. Any issues with it working properly with the heavy 12 volt power wires so close? I hate to install the sensor on the gunwal.

Dude has done this a time or two.

Good teaching

Thank you for posting. Any suggestions on how to wire up a trolling motor and install batteries for a cuddy cabin walkaround style boat?

Great video Chris. Just realized you through bolted your bracket with nuts. Is there other types or ways to mount motor if you can't do the bolt through? Thanks, Steve

I have a Campion explorer 492, I'd like to install a bow mount on it but there is no access to get to the bottom of the bolts. Could I use toggle bolts with thread lock (and adhesive like you did) to hold it on? or do you think they would rip through the fiberglass going down the road? other issue would be the stainless bar on the front.... but i figured i could just extend the TM all the way before dropping it down... any insight would be helpful, thanks

How did you close the anchor locker?

did you use the metal washers aywhere in the install? I was wondering what that use for when i install mine.

What mounting bracket did you use?

Remind owner to calibrate his TM and set the Off set . Most new owners don’t understand that. (Not sure if you water tested it and did that for the owner)

Would it help to put a backing plate as well before the washers and bolts, or is the deck enough?

where did you run your power wire from the console to the anchor locker

Great video! Answered all my questions but one thing I don’t get why would you mount the plug inside the anchor or any other compartment door? Now when a wave comes over the front it’s going straight in the compartment! Why?????

Which one can I mount at the Old Town Sportsman 120 PDL?

how did you snake the power cables to the TM?

Nice

What size motor would you recommend for a 2004 SeaFox 210 cc ?

What bracket are you using?

I already have a simrad heading sensor for my chart plotter tied into my nema network. Can the trolling motor tap into the heading sensor I already have installed? Or will I have to install another one?

Just had this done on a r 200 but they put it going down the port side then drops into the water just left of the port light.

Is your on board charger connect to your outboard/motor? Or it only charges when you connect to shore power/ac outlets?

I own a 2018 R200. I am installing a Minn Kota 72" 36v Trolling motor. Your viseo is very helpful, But it does not show how and where you fished the wire from the CC to the anchor locker. Can you give me an idea on the installation. Thanks Ken.

Whata about the ipilot cable?

The front 2 holes should be over the flat deck. Look at the ShuttleSlide trolling motor mount. It would really help with this type of install if u do one like this in the future

what voly batteries you hook it up too?, i see these are 24volts most of them

How do you run the cable from the batteries up to the trolling motor?

does it bring the hardware and bolts?

How do you Kno where to mount it on the bow

I don't know what modeling agency you were hired from... But DAMN! Aren't you a handsome sight to see. Boats perty too. 😂

what if you couldn’t reach underneath? Just use self tapping screws?

What minnkota do you recommend for a R180?

Why couldn’t you mount it in the position like you have it resting at 5:19 of the vid? I know you have it just sitting there out of your way while you work on the mounting on the other side but that looks way better and out of the way

You can tell this is his first install. I’m totally kidding! This dude put all other install videos to shame!!

how was the wiring ran? that part completely got skipped.....

I’ve gone through a dozen of these how to videos. Not one addressed the problem with blocking the navigation lights.

Too bad your cleat is right below your new trolling motor.

Antiseize is your friend on those through bolts

Good afternoon. When turning the engine to the right, it makes much louder noises than when turning it to the left. What can it be? Here on video. kzfaq.infoqCgITsiLa8g