Great vid! I also see lots of people just "throwing pistons in"...its great that you brought to light the importance of ring end-gap.On a side note though,i usually measure the bore before measuring end-gap and measure end-gap where the bore is smallest....usually it is smallest and least out-of-round just above the transfer ports or somewhere close to the center of the stroke.just thought id mention that.thanks and keep bringing on the great vids!
@mykecollins32557 жыл бұрын
im no master mechanic and I'll probably catch hell,but i thought that checking ring gap was a absolute no brainer?! thanks for all your videos..love this channel.
@AkMedMan17 жыл бұрын
Love the tech vids Louie! Especially the Polaris and Landcruiser ones!
@kx65andyx85rider7 жыл бұрын
I feel you with the rain. Down in Mn we just barely get enough snow to ride then it rains .. sad sad time
@yveskc17 жыл бұрын
Thanks for the info, i like these kinds of video.
@SnoStig7 жыл бұрын
Your kids a good camera man
@thedogemachine1307 жыл бұрын
Vary nice love your videos!!!👍👍👍
@corey5207 жыл бұрын
Maybe mention there is such a thing as a ring filer tool. keep up the good work!
@luclaurin46907 жыл бұрын
ring end gap thats ok but now when ur done for the gap you have to file the end so you have no sharp edge (debure)
@davepoidy5520 Жыл бұрын
thanks for that
@PowerModzOfficial Жыл бұрын
No Problem Dave!
@type1warroirrath4275 жыл бұрын
What kit do you recommend for the 800 cfi ass far as reliability goes. Have you tried the ssi kit? Thanks
@pjakk847 жыл бұрын
Next time if you are doing big bore, maybe Terra Alps racing?
@ethan513007 жыл бұрын
I saw you in Carlton place today
@ericfeuerhelm24593 жыл бұрын
Nice toque I just work with Chris Evans down in Cranbrook
@MrPowderEater7 жыл бұрын
so Kelsey switched from the German pistons to wesco?
@MrBIGG3607 жыл бұрын
Do you have to do anything cylinders before putting in rk tek pistons. Thanks
@zachfoley73947 жыл бұрын
Is that the kit that comes with the spacer?
@nathanball27447 жыл бұрын
Do you still have any of the iqr's?
@aidenpearce75667 жыл бұрын
What year is your rev
@aldesrochers7 жыл бұрын
Where is that chainsaw mounted on the bicycle???? LOL
@dfuller9687 жыл бұрын
Kids do better than the adults on the camera work!!!
@elijahballantyne86705 жыл бұрын
How would I know what size gap to go with i have a 2010 Dragon 800 rmk ?
@cdnbcn61644 жыл бұрын
Your ring gap will be listed in the manual. .
@shnill7 жыл бұрын
if you had a tight ring gap, would you have an issue right away? or could you run it hard for 1200miles and not notice a thing?
@RenegadeRiderBC7 жыл бұрын
Lol that sounds like someone may have not checked their gaps...😏
@shnill7 жыл бұрын
TheHerb lol no no - that's the first thing i do, just curious. never seen a failed engine due to ring gap issue
@maxboisvert67387 жыл бұрын
Too tight will break your piston when overheating
@paullunney32057 жыл бұрын
do you know if the gap needs to be smaller or larger with a turbo?
@PowerModzOfficial7 жыл бұрын
it needs to be to the manufacturers specs.
@aarpaz7 жыл бұрын
Typically larger
@ujarneqsrensen87457 жыл бұрын
How do you like those RKtek pistons, are they holding up?
@PowerModzOfficial7 жыл бұрын
Ujarneq Sørensen I abuse them best I can with no issues.
@ujarneqsrensen87457 жыл бұрын
PowerModz sounds awesome! I think I'm gonna go with RKtek when I rebuild the top end of my 16 RMK. So far I've got about 4500km without issues, but I'd like to change the pistons as a precaution. Are you having issues with the motor mounts on your turbo? Mine are worn, and I feel like it doesn't perform as good as it usually would do.
@ryankravik93096 ай бұрын
How long did this piston kit last?
@PowerModzOfficial6 ай бұрын
Still going
@welderteach7 жыл бұрын
Did I miss something? Why the new top end?
@PowerModzOfficial7 жыл бұрын
Trying out his new pistons - the others were fine.
@PolarisEricson7 жыл бұрын
welderteach low compression head to stop the detonating issue with the turbo
@ajjelly30317 жыл бұрын
whats up witht he camera... its only playing in 360p
@PowerModzOfficial7 жыл бұрын
Rendering
@ajjelly30317 жыл бұрын
PowerModz ... o ok... P.S. love you vids keep em up. good job...
@radioactiveload7 жыл бұрын
give it a minute, it probably hasn't finished uploading fully
@2007dalin7 жыл бұрын
hate to be that guy.. but technically your doing it wrong.. if you apply side pressure to the ring it can get warped. better to use a file and pull it back and forth across with just the ring tension or use the tool made for it
@machine77673 жыл бұрын
By directio do you mean from the center of the piston to the outside?
@fakegibsonssuck77557 жыл бұрын
Should file from the inside out, if that was a moly ring that would be destroyed now. Not trying to sound like a douche Louis. I love your videos.... You should get a ring file machine, you do enough top ends.