Plunger Selection for your Riflespeed Gas Control

Рет қаралды 5,930

11 ай бұрын

Rob covers the basics of "why" and the simple process of selecting the best Plunger for your specific AR configuration. Every Riflespeed Gas Control comes with two Plunger sizes to cover most applications, but you can select from 10 sizes if you want to fine-tune your performance.

Пікірлер: 16

@hdd7955 9 ай бұрын

Awesome! I’ll need to install the shorter one now, my rifle wouldn’t hold open at 12 but when I added a suppressor it would hold at 8. Thank you for the clarification.

@danielhess39 4 ай бұрын

Great knowledge!!👍🏼🤙🏽

@dejavu0000 6 ай бұрын

Can you close off the port with the longest plunger then? I want to manually load 300 blk suppressed sometimes

@pogo458 10 ай бұрын

Also the max length tube is 1/2” too short….. you can sell a shit load of these for the Ruger SFAR customers

@pogo458 8 ай бұрын

I ended up buying a short hand guard which is better than stock

@Gdogg617 6 ай бұрын

So this in fact with factory plunger will give the rifle the ability to cut all gas and essentially make the bolt not cycle like a bolt action?

@Gdogg617 6 ай бұрын

@riflespeed

@scottbenton5880 3 ай бұрын

I'm pretty sure that the plungers included with this gas block won't completely block the gas system. I just got one but haven't installed it yet. When looking up through the gas port opening at the top of the block and at the lowest setting of 1, it appears that the end of the plunger doesn't fully block the opening. It should be possible with a longer plunger.

@jst4kix 9 ай бұрын

This is very informative! Just the information I was looking for. Question: I bought my riflespeed setup last month, but am still waiting on my upper to complete my build. The package came with a second plunger, but I can’t find where on the packaging what size it is. Can you please let me know what the size is of the second included plunger? Thanks!!

@darkhorsetactical2371 5 ай бұрын

Plunger #887 is included in the retail package with each RIFLESPEED™ Gas Control (manufactured after June of 2023. In conjunction with the installed Plunger #917, these sizes provide coverage of the nearly the full range of potential settings needed for every configuration we've identified during development of the RIFLESPEED™ Gas Control and allow the shooter to select the best Plunger for a specific firearm. Additional sizes are available for those who choose to precisely tune their Gas Control's settings or who have a configuration that falls outside of the more typical range. We will work with you to ensure you have the correct size for your firearm if the included Plungers aren't right for your setup.

@pogo458 10 ай бұрын

I have your Block… looking for the recommended pins for my Ruger SFAR 16” for 7.62 and hot 308

@godfreywashington3269 7 ай бұрын

😂😂😂 lol I'm running a strike industries adjustable gas block!! The stock one just doesn't cut it!

@breckfreeride 6 ай бұрын

With the huxwrx ti 762 and light loads (armscor 308 and 7.62x51 fed) in 30 degree temps it runs about a 6 to 7 with the stock plunger. I ran a few hotter loads unsuppressed and was getting lock back around 5. Ymmv. Hux is a very low pressure can. I'm thinking of trying the shorter plunger bc 30 is a warm day on hoth but I bet in warmer temps I will go back to the larger plunger.