Thanks for the video. The fix is somewhat easy, the hard part is knowing if you still have enough oil in the fork if you didn't notice the leak soon enough.

It's all about the seals, nice work mine needs sorting but may try this first. Thanks big man

You the man! You saved me some$$$. I had to do about 6 sets. Pulled the cap down stuck the tool back in to verify there was still oil in it. Did one more set. Clean!

Great video bud! I know it's 2 years old but i just found it. It helped me because other videos don't show what happens after the cleaning. Also it did help me not putting dust seals back. I thought if after the first set of pumping they get contaminated with oil then it might not be fork oil coming through fork seal but dust seal leaving residue. Got a perfect seal after 2 sets of pumping. Thanks again!

Worked for me! Fixed my seals on my Aprilia RS4. Thanks :))

Good temporary fix , but that oil xx per leg is important . You need between 390-420 per leg and to bleed the inner cartridges . Thanks for sharing the video . It’s a good little tool that 🤘

Nice video! Awesome bikes!!

Good video, worth a go, cheers.

be wary that those shocks hold a certain amount of shock oil in each one... and there's about a 2.5-3mm tolerance before it detrimentally affects the suspension! the more it leaks, the less the shock dampening... meaning the front end of the bike will just bounce like a pogo stick! make sure to know and understand the fluid levels of the shocks on your bike and check the levels after using this thing!

lasted one year , thats really good

bro i hav same bike 8 model does changing bore kit make bike engin run lik new?

I appreciate this , even if it works or not , I’ll try it before I go ham sandwich and do new seals .

It’s the price you pay for all the wheelies mate 😂good to see videos from you again 👍🏻

Where did you get the seal mate from?

Looking forward for more vids

Thank you so much.

You should wipe it every time you finsh your sets of 10 pumps, your still seeing residual oil from the seal cleaning. Use a clean side of microfiber towel every time

How miles did you done since last time you used this procedure? I mean how long could you go until you need to do this procedure again?

pog, thx for the video m8

My fork seal is stuck on my cbr600rr how do I get it off without breaking the seal

Thanks for that 👍

you can use a feeler gauge blade 0.1 mm instead or use old photo film negative or 35mm roll film.

It freakin worked no way haaa hell yea

السلام عليكم Thank you for sharing

Do not sand the leg or you will be changing seals much more frequently the leg needs to be like a polished surface

Loool@ I'm not going to the gym today.....

I’d probably service the forks. If there’s a leak, then more than likely there are contaminates in the oil.

Any news on the street fighter??

Bismillah!

The big problem is with street bikes or big scooters you have to take the bike apart to refill the brake lube 😢

Ohlins USD fork 😁👍

Did you check on the oil level? You may have run out of fork oil and the leak isn’t fixed, just dried up.

The way you cleaned that fork was sus bro 🤣

Whats the name of the tool

Where do I buy that at?

is this a permanent fix..? my fork have the same problem..thank you!

Don’t keep doing this and run out of oil and think it’s working.

Sand the chrome with 400 grit

If anything you just made it alot worse

You guys are so cheap! Buy new seals, remove forks and remove/replace. Not a difficult jog at all !! New oil while your at it. To press the new seals back in use a 34 or 36mm 1/2Drv socket and tap them in with a hammer. No need for fancy seal drivers. Monkeys can do it, super easy.....