Ah sorry I should have put this in the description this Farm has no livestock they use the hay for the burners I'm no farmer and dint know exactly what they do but big mounds of spuds and soil was everywhere 😂👍💞

@@Mobileblaster ah that’s good to know! The idea of a cow eating tiny bits of glass made me nervous... cheers!

@@telekommotorrad9065 yeah I should have made that clear my fault sorry :)

Hey mick I'm a blaster also I'm based in wexford in Ireland you done a great job there mate and very little dust well done from one blaster to another 👍

@@mickdelahunty5026 thx mate it's appreciated 👍💞

😂 his main call to action was if it looks good on the road the police are more likely to leave him alone haha with it been Farm 🚜 agricultural registration he don't need to mot it but is restricted to how fast he can go. No mot but he can still get done if its defective like bold tyers no lights etc 👌💞

You should try it sometime.

😊👍👌

I don't mind doing eva but I've learnt not to do stuff I've not been told too 😂

magic wand haha :)

Thx mate 👍💞

😊👌👍

😂 not half one of the worst jobs if ya like staying clean 😂

@@Mobileblaster Nobody hassles you once the grit gets flying though .

@@twostix67 haha that's about best bit of job lol sometimes I wish pot would last longer than a hour then other times I wish for it other way round 😄

@@Mobileblaster Its strange how those clip board carrying hi viz wearing health and safety wombles stay well out of the way as well lol

😊 I have plenty more feel free to have a snoop through my other videos 👌👍

Don't let the sales pitch sway you buying 1 they say they add power it doesn't ad anymore power just that it keeps the hotspot in a tite cone for longer 👌💞

@@Mobileblaster I know what you mean mate.but they look good to use in awkward places 🤗👍

Yeah but are they worth the money? I would say yes as I like the easy life but I could have managed without it. They are expensive but once you have 1 try and only use it when needed that way it will last as long as possible 😊

@@Mobileblaster yes know what you mean mate.will have to price one on line to see what it costs 😁👍

@@briancamac4573 normal nozel £180 ish xl turbo £550 ish depending on who you use 👌 oh and it will were quicker than a normal one 😳

👌👍😊

That would be very dangerous 😳🙈 I can set it so I move a slider and it blasts slide it back it stops but even that is too dangerous. As it is if I slip or pass out drop it the blaster etc it will shut down hence the name dead man's handle 😁 I know what your saying but from a safety point it needs to be done like this 💞

🤘👌💞

They do them but in my experience they seam to work out the same speed or slower as it reduces the psi of the hotspot its kinda hard to explain 🙈😂

They do have bigger nozzles, but faster means less money, that’s why he white metal blasted it while pointing the nozzle inches away from whatever he was hitting, that should’ve only took a few hours while using way less sand.

@@AylerProductions Bingo

😬😊👍

Quite good 🤪 😂👌💞

@@Mobileblaster ok brilliant, 😁😗

@@phillipsharpe6459 😊😂 for the time involved I would say it's the best thing to happen to that trailer its old he knows that and the value isn't in the trailer to fully refurbishe it all he wanted was it to look good for a few more years 😁👌💞

😊👌👍

No only work is drying up since the covid but I'm managing to keep afloat 💖 to be fair I stock 27+ton so I have a little buffer if I've to wait for stock 👌🤘

The air mover needed would need to be huge to move the volume of air needed. I'm maxed out as it is with what I'm aloud to carry in the van 😔💞 welcome to the party 👌💞

😂

using choke would push more sand I don't need more sand? the xl nozzle gives that bit more reach than a normal size nozzle same bore same psi same media just a longer reach with the xl nozzle (all it dose is it keeps the hot spot cone for a longer distance)

Thank you 😊

Ooo I don't mind trailers I don't like using anything over 400cfm my next video I have to profile steel 600cfm with steel shot I really don't like using steel shot that stuff hurts well it does at 600cfm blow back haha

@@Mobileblaster totally agree steel shot or slag or pretty much anything that is a really corse media sucks to use. Mostly I use 50/60 green diamond for just about everything.

@@devininwetrust9610 I like glass 😊 from super fine to medium that's my go too 👌

I believe if your a painter leave the blasting to someone that does blasting why would a skilled painter try to learn another skill? It's like a roofer learning how to lay bricks kinda makes sense but not really haha

12 hour over a day and half 👌 I would have done slightly more if he said he wanted a day and half to start with 😳 but he only decided to do more when he realised it would look better than he thort 💞👌 I use 260cfm @125psi possibly 100psi at the nozzle 👍

I cannot remember off top of my head as it was some time ago if was to go do another I would take 1000kgs on the hopes I would be bringing around 350/250kgs home

Don't need MOT with it been agricultural registered that's why he wants to make it look better to keep the plod off his back 😊

Hi I'm using the nova 3 not the 2000 :) each blaster will have their own way of doing things the reasons I do it like this, For any more media flow wouldn't give me a faster cut the only thing that would have gave me a faster cut is heaver media and more air cfm in both cases the media needed to cut slightly faster would have been almost 3x the cost of glass and ive tried it in the past I don't fink it cuts 3x faster. So in my opinion not worth the extra cost. More air would be nice but in the uk I'm limited to what I can tow and my 260cfm is right on the border of my vans safe towing ability. More air would drink more derv in turn only saving a little extra time but adding more cost to the job. The Nozzle/tip is set for 260cfm @100psi a bigger nozzle wouldn't gain anything only slow the job down bigger bore will lower the psi anything below 100psi isn't optimal. Anything over 100psi is unsafe with my pot and nearly every other on the market is rated to operate at this. The job he wanted was quoted 8 hour but he then asked for extras taking it over.

Pressure pot 👍

Compressor doosan 7 71 (260 cfm at 8 bar) blast pot is a presure pot 👍 yeah the full rig tuck some time to earn its keep haha just about paid off and now I need a new 1 😔lol

@@Mobileblaster Do you use all that cfm? What's the lowest cfm you would recommend for blasting?

@@Mattie_Ice cfm and psi is determined with the nosel and pipes what helmet etc etc I'm running at optimal 198cfm to the nosel rest to presure the pot fees the helmet and any air left will counter the slight were on my nosel 👌 blasting can be achieved with any cfm you need to know cfm you have before buying any equipment. Only 1 real thing to think is bigger the better but derv and mobility then play a massive factor so it's all down to skill level if you get the most out of the air available. Without sounding like a cock a skilled bloke could operate a 140/180cfm and out perform a novice on a 300cfm with efficiency media and derv wise plus the visors that's likely to be used up quicker with less skilled bloke. Basically the better you get at it the more you will save good luck I personally started with a 140cfm and upgraded to 180 around the 2 year after mark then 3 or 5 year after thet I'm on a 260 and find it to be perfect for me but if my driving was any less skilled I would definitely be picking 180 as these can be moved by 1 man well kind of 260 is a 2 man job if your driving is a little poor haha

@@Mobileblaster Thanks for the reply. Will help me make a choice.

I price per job as I know how many hours a job will take me to complete.💞

@@Mobileblaster what did you charge for that job

@@johncarroll4448 for inquiries please email info@mobileblasting.co.uk Regards Mick

I was in a celler in a funeral parlour to expose some steel structures. When I had to stop to let a funeral take place above me 😵

125psi @ 260cfm 👍

I tend to disagree hears my reasoning, If I did turn it up I would have wasted media yeah it would be a little quicker but wasting 60/70% of the extra media (with rebound hitting the stream) when im the 1 buying the gear I find a happy medium with derv(air consumption) and media(coverage) I find if the nozzle sounds like a whistle its too low and extra media could be added if it sounds like a train chu chu chuc etc its way too high anywhere in this range (with out theses sounds) is ideal for me. I find lower media more air makes a better profile as the air has more chance of pushing lower volume of media at higher speeds than big lumps of media thats going to re hit the rebound. I like to try and be in the optimal range :)

Thx it's appreciated 👌💞 what's you location plz if your outside the UK I have no idea 😂

@@Mobileblaster Manchester 😂 ( U.K.)

Ideally you need to do some sort of training from a blast suppliers their is no set rule that you need to but for your safety and other around you I did 😊 then you need to get insurance in place boom your in business 😉 I will just add I do make it look alot easier than it is just like any other trades person that's decent at their job plastering springs to mind it looks easy but I've tried that and it's not haha. I wish you the best of luck tho and if I can help in anyway I will 👌💞

@@Mobileblaster yeah I’m not the type to jump into something lol, defo don’t want to be all gear no idea 😂. I will do some more research on it, thanks for your reply I appreciate it. 👍

@@Rickym403 If I could speak to a younger me I would say listen and learn at school so you don't end up getting covered in shite for a living 😂🙈💞 its definitely not for everyone you may be better trying to find a job doing it 1st and seen if you can cope with the helmet 8 hours aday and the dust all over you every day 👌

Pressure pot any will do the bells a whistles are you to you and your workload 👍

Yes I have the ability to dry/ wet mix at nozel or fully saturated in the pot. Wet on this would be near impossible unless I wanted to get a mortgage to cover the cost of the visors I would need 👌

Thx it's appreciated 👌👍💞 and sorry I don't know I've downloaded it from the youtube studio and I have a small selection I like off that 👌

Sorry not at the moment

Hello and welcome to the party :)

For all business enquiries please email info@mobileblasting.co.uk Regards Mick

Hi its a doosan 260cfm my go too media is crushed glass from dust to medium I think this was fine + and 125psi so around 100psi at the nozzle 🤙

Thx it's appreciated 👌💞 but I'm no painter 🙄 I wouldn't recommend anything I don't use or know much about 🙈

Epoxy primer is the industry standard for shot blasted trailers. It is a good thick coating that goes on before adding a colour.

@@mycarprobs6688 Yeah I've heard my brother mention something like that before. This guy was going down the DTM paint root (direct to metal). Its a all in one other names ive heard people say is rain coat/ one coat, loads of different names but its all the same thing I don't know if it's any good like I say I take paint off not put it on :)

No this was painted in place 👌👍

😂😂😂 funny you mention the van I'm just as we text having a little brake and finishing removing the stickers so the next time you see the van eva sticker free or new design I plan on doing these myself I don't know no if to do a video what you think?

@@Mobileblaster Definitely .. a DYI decal application ..We had our M-B vans professionally vinyl wrapped , but that would make excellent video content 😍

@@angeldawnmorningstar only 1 problem I have no idea what I'm doing 😂😂😂

Crushed glass 👍

Not really as this is 1 x hit possibly 2 x but after the 1st hit it brakes up so I wouldn't get a uniform finish. I could use a different media to last longer but the cost is up on that and then the productivity is down so catch 22 some areas it would pay some not so good. Everyone finds their own style and what works for them I add these costs into my price obversely and it seams to be working for me. :)

@@Mobileblaster yeh it makes sense bud, it probably ran through my mind in a logical way, but I chose to ignore it 😂, I used to paint that stuff a while back and the set up we had was a small warehouse where it would be blasted before the paint went on, and the shot was on the floor to be later swept up to be used again, so I do see the point👍 very therapeutic

@@Amac-uz9hm yeah sometimes on the right job and location it would pay to do it that way :)

Saves alot of man hours sanding 😊💞

@@Mobileblaster do you ever get cars in for blasting or is it more industrial sized stuff

Yeah I've done quite a few just that I've not had any crop up since doing the youtube channel 😳 maybe 1 or 2 on my channel but nothing with fairly decent editing 😂

@@Mobileblaster Oh nice, what kinda money would you usually charge to do the underside of a car ?

@@bendude6748 totally depends on age of car etc if your in Yorkshire send photos to info@mobileblasting.co.uk and I can get you a quote 👌 Regards Mick

What the shell? Or chassis?

Only a bit of dust 🤗

@@Mobileblaster i don't think so)

@@verossavr3027 it gets alot worse most other days 😂 I'm just on with editing another video and I show a clip of the van getting washed its unrecognisable until water hits it 👌 should be on today at some point I hope 😀👍💞

😂 I can say 90% of jobs I do say it 😂

@@Mobileblaster lol .. I'm a long haul trucker. When in Penrith a few years ago, the "Can you just drop that at Carlisle, it's just up the road" without understanding the truck does 4 miles to the gallon and costs £4 odd a gallon. And expected to the job for nothing... "Can you just" lol

@@stelsewhere11 😂 can you just... lol

Hi sorry I'm not setting on just yet 👍

😊🤘🤙their is no set way to blast. I will do a tips and tricks video soon as to why I blast like this and the reasons my change how you may think. Keep an eye out for this video soon 😊

Yeah its recycled bottle glass. It could be reusable again but for speed of the job I don't reuse the media. Plus once its been used it brakes down and don't leave a uniform finish if its used more than once.

@@Mobileblaster thanks for the information! What about the broken/ worn-out media? It is hard to recollect as it mixed up with soil and therefore contaminating soil or is is recycled into glass again? Anyway great to see your work and even greater was your prompt reply! Cheers 👍👍👍

@@ravindernegi7419Thx it's appreciated 😊💞 the media could be used again but I don't for the speed aspect of things. It wouldn't affect the soil/ground as its none carcinogenic and the paint was water based so biodegradable 😊

@@Mobileblaster thanks indeed 👍👍

Yeah I use nova 3 👌 gloves they are only for when it's cold? 😂 I definitely wouldn't recommend it but I know this is no excuse I have alot of experience with my rig and feel confident enough not to blast areas that don't need it ie my digits😂

Non c'è bestiame in questa fattoria, coltivano patate. usano il fieno per alimentare i bruciatori :) No livestock is on this farm they grow potatoes. they use the hay to fuel the burners :)

Yeah he sorted me out on the extra bits 😊 the hay was only used as fule for the burners he was running it wasn't animal feed 👌

Not at the moment buddy but if you follow my Facebook page mobileblasting.co.uk I put it on their 1st when I am 💞👌👍

If the Nozzle wasn't supposed to be held why has it got nerling on for grip? The job sheet on this was to do the face's none of the underside 👌 the media used won't damage the threads just clean them out I'm able to blast wires and airline's with out busting or cutting through them I know they will be fine 👍 to make a complete perfect job it would need stripping to an inch of its life have it over a pit etc but the man hours alone would value the trailer as scrap all he was after was a tidy up so the old bill don't pull him over as he moves it from 1 field to the next. With it been agricultural it don't need MOT (UK tests to say its safe for the road) same again it won't be pulled any faster than 25mph and a maximum of 1.6km from his farm or land 👍 he just wanted it to look fresher than it did 😊 please have a snoop through my other videos 😊

Understood bro. I’m just extremely fussy. 👍🏽

I’ve seen nozzles come off not a pretty sight. Holding the hose also makes for better control as you can make it do the work for you. 😀

Thx it does look easy but the is more to hit n hope haha. I can answer any questions you may have on hear that way it will help the channel out with other people may have similar questions I don't want to keep repeating myself 💞👌👍

@@Mobileblaster I've been happing trouble with my compressor , compressor oil going in the air lines? I'm after another compressor if you know for any for sale

@@rhyslewis2062 What compressor is it? You can easily fix that issue no problem swap out the air oil separator buy a service kit for said unit change the filters and oil should stop that issue 👌💞

@@Mobileblaster atlas copco 180cfm mare.... I seen you might be selling yours buddy

@@rhyslewis2062 no mine is not for sale 180 is about the best all rounder I would service and keep using that.

😊👌👍

What's that?

@@Mobileblaster sand blasting process is very dangerous for lung health. Because of lung ca

Not in the products I use. I use a media that's none carcinogenic and the paint removed is water based paint. I wouldn't recommend breathing it in but it is clean dust 👍💞

😊 hi fellow blaster 👋 it's how we keep the lights on I suppose 😂👍

@@Mobileblaster عزیزم لاتین بلد نیستم😇🤣

😂 worlds apart 😊 but we are in the blasthood together 👌👍​@Naserallh

🤘👌💞

How would you switch things up bit?

@@Mobileblaster it's a job in which you have to develop yourself, and I'm still learning))) it's perfect when the iron is the same gray, for example, perfect clear ,good luck perseverance )))

@@valterunger4141 I kinda want to get better at explaing what I'm doing, how I'm going to go about it and why but I totally get soaked into the job I forget about the camera :/

Best rust inhibitor man has invented 😏