Replacing The Front Bearing on Mercedes Benz W202 (Same as W124, W210, W208 and more)

Рет қаралды 12,511

4 жыл бұрын

This time we are here with a new video on how to change front bearings on w202, w208, w210 or w124 (Possible on more chassis with this kind of system). Why this car needed a bearing replacement and how did I know it needs to be replaced? One day I was trying to do donuts on both sides - that was when I realized left shock absorber has gone bad. When I tried to spin a donut on right.. Left wheel started to jump forward and that ended the bearing. On a way home there was a noise and vibration on the left wheel that could be felt on steering wheel. These type of bearings needs to be set with a special tool to measure how hard it needs to be tightened, but we just tightened it in the spot where the hub did not move anymore - make sure you do not over tighten it because that will destroy the bearing and you will need to replace it after a while again. How to know that you tightened it too much ? - After a drive your hub will be really hot. Be careful how strong you tighten it! And stay tuned for more videos!
Latest news are announced on our instagram page - / garagify
Instrumental produced by Chuki. Check out his channel: / chukimusic

Пікірлер: 29

@juniorbeginnerbeginner1790 2 жыл бұрын

I just did mine today good trick heat up the hub and then put the races in the freezer they fall right in

@777xpressmusic 4 жыл бұрын

Good job👌🏽

@javierfalcon1141 2 жыл бұрын

Gracias amigo me voy a mi garaje a trabajar en mi Mercedes Que Dios te bendiga por compartir tus conocimientos ya me suscribí

@woodroblue8332 2 жыл бұрын

Thanks gotta do mines now

@YUSUF-zi6ri 2 жыл бұрын

Poryayı takarken çekiçle vurarak oturtmaniz gayet başarılı

@supercharged.c230 Жыл бұрын

Nice that seems easy enough but my car will have the.bearing locked in the hub and shit. Lol..thanks for vid..

@garagify4255 Жыл бұрын

Hammer and angle grinder will help you!

@donnymontreano9235 Жыл бұрын

hi how are you? i want to know if the steering knuckle rod can be replaced with a longer rod?

@trailblazer1281 2 жыл бұрын

Great video but everyone misses explaining the seal

@youngirab3913 5 ай бұрын

you forgot to put the seal on??

@TheDickMan_ 2 жыл бұрын

I like when a man lubes up his shaft!

@redeemernigoohaem9735 3 жыл бұрын

Did you tap the bearings in or just place them?

@garagify4255 3 жыл бұрын

Tap

@redeemernigoohaem9735 3 жыл бұрын

@@garagify4255 wait it didnt show you tapped the bearings . Only the races . I just put the bearings, the parts with the balls inside by hand . Seems fine . This is what I meant . I tapped in the races , not the other parts .

@garagify4255 3 жыл бұрын

@@redeemernigoohaem9735 Sorry, misunderstood you! Yes ofcourse only place the bearings in races. Make sure you dont overtighten the nut at the end!

@redeemernigoohaem9735 3 жыл бұрын

@@garagify4255 thank.you ! Btw my car is c180 1995 . Everything came off clean , except one rotor was stuck to a hub . Didnt have to hammer in the hub . Also the small race was not the same level . It had the placement outside leveled. Not deep like your model . Only the big one was 4 cm inside or like yours . The other was leveled on the surface . There was no more space to tap it .

@garagify4255 3 жыл бұрын

Do you have pictures of your work? Can you send them to us on instagram? So we can see whats going on there.

@alinazeer9774 4 жыл бұрын

Hii I owned Mercedes Benz e240 or u can say w210 station wagon 2001 rear shock absorber is hydraulic I want normal air shock absorber ???? Can I install plz can any one help me

@garagify4255 4 жыл бұрын

Yes you can! But it is not recomended.

@didzisbilinskis8312 3 жыл бұрын

Labs content un video kvalitāte arī laba. Ceru ka nepadosies uz yt😁 gaidisu vel vidakus

@redeemernigoohaem9735 3 жыл бұрын

My hub is stocked to the rotor . Any tips ?

@garagify4255 3 жыл бұрын

Try using a puller or a hammer to get it off. If inner part of the bearing is stuck on the hub - use angle grinder to get it off. Good luck!

@redeemernigoohaem9735 3 жыл бұрын

@@garagify4255 hey ! Thank you. I did it last night . I didnt see it right. The slope was part of the cover not connected to the shaft . That s why I was not making progress.

@redeemernigoohaem9735 3 жыл бұрын

@fupabox I took everything out . I have a problem . When I hammered the rings out there s some chipping there . On the hub . They are small but I'm not sure how it will play out . If I hammer the new bearings in , it will maybe bend n level.the surface Dont want to use sandpaper n the chisels r too big for it I'm.not sure what to.do. Second one I was more careful. But if I was to.tap it perfectly carefull it would have taken hours n hours. I.domt think it s possible to take it out clean only with screwdriver n hammer. Will it be alright if I fit in the new barings on it ? With these chips ? Or how to grind them ? Thank you btw

@garagify4255 3 жыл бұрын

If the chips are on the outer line just make them in level with the surface so they are not in the way of ring and use some lubrication to hammer it in easier.

@redeemernigoohaem9735 3 жыл бұрын

@@garagify4255 what can I use to make them level?