This video is the main reason I did my clutch install by myself without paying a shop. Thanks man you saved me a ton of money.

Saving us all money as usual brother , your videos have literally saved me over a grand due to showing me how to do my own work in easy clear concise steps ...helping us all 🤙

Glad to know what I am gonna have to do to my RSX when I have to replace the clutch.

Hey man that's a great video. I like the way you explain and find the best way to complete a job... thanx.

I'm about to replace my clutch and had no idea that the subframe has to come out definitely saved me some time and headache lol thanks man!

I just got an 05 RSX and in the future I’m sure I’ll be changing it so thanks bro

thank you sir , u save my bucks and build my confident doing the clutch job !

Hey Serge good stuff keep'm coming. Get a shop led flood light that sits on the floor which you can direct.

Good how to video on doing the clutch.

Comp clutch or Twin Disk The way to go for great gab daily & race.. #Respect 🙊🙏

"Stick to using bread... Or you can just use the right tool." Haha.. I've been using the bread method for many years. Always worked for me.

Use the socket to hit the bush in from the start, so if you dont hit exactly flat, it won't matter, the socket WILL be flat on the bush and you wont create any burs on the soft metal. Hydraulicing them out with bread or grease only works when you have a mostly complete seal, an open socket can't work with an escape route down the middle. a bolt slightly smaller than the ID works, a machined rod is perfect. Good job man.

my ep3 si clutch finally went out today i just order all the parts i will be removing the subframe an trans while the parts get here its my first time doing a clutch i will pick up some engine degreaser a torque wrench at my local O Rielys

What would you say is the hardest step when doing this on your own? Reinstalling the subframe?

Sweet vid I feel like I can do this now

Thanks for the video bro! I just did mine a few days ago and now the car won’t start. any idea of what could of happen? car was running fine before replacing the clutch

I'm having a hard time taking out the ball joint from the lower control arm

Sticking bread up your car holes was the ultimate DIY advice.

Getting this done on my 2005 Civic Si EP3. My shop told me that the front suspension has to be dropped to access the clutch and replace it. I'm getting an Exedy stage 1. Should have it back in about one week.

I have an 02 rsx and I need to do the same thing to it. But for some reason my clutch pedal is set up high. Is there a way I can adjust it to make it release sooner?

I have a 06 rxs base with a type s trans in it before I replaced the clutch it was hard to shift and it wanted to die when I pushed the clutch in. So I replaced the clutch pressure plate and throw out bearing shift great now but the car still want to stall when pressing the clutch it. Im lost on what it could be

When I’m done installing , do I need to add brake fluid to the clutch reservoir?

Im really on the fence about doing this myself. will be the biggest undertaking for me mechanically. Oh well gotta replace my valve cover and vtec solenoid gaskets first then will think about this.

If you’re rebuilding your transmission do you have to drain all the transmission fluid?

Instale el flywheel 11 libras y el clutch competition stage 3 pero mi carro no acelera solo acelera a las 3 rpm no se que hacer

Is getting new flywheel bolts not needed ?

So I did evey step and wen I got it back together it won’t engage

Did you take the starter off ?

Muy bueno el video hermano

I have a question

If you toast the bread will it work better?

Do you still work for customers

hey can you do an install video. step by step for the skunk2 pro series intake manifold and throttle body install

Where are you located bro??

Dope music

Cool !!!

Great video, Maybe you can help me out. I've been trying g to help my nephew put a trans in his 2003 rsx...but it feels like it doesn't want to go together with the motor. We did use alignment too when putting in. I was thinking, the Intermediate shaft is still on motor and we're trying to line that up plus bolt trans to motor....should we just take that off and put intermediate shaft on after trans is bolted up? Thanks!

Solid video. I just had my clutch replaced in my type-s and there is more travel in the clutch petal (petal goes all the way down to the floor now) Is this how its supposed to work with a new clutch?

Question I just did my clutch now my rsx cranks but no start what can it be

Good video skips every hard part of the job

I want upgrade my clutch and fly wheel but my mechanic says I have to reflash my ecu for make it work, is it true?

Simple question do you have to adjust your pedal clutch engagement after you install FX 300 clutch master I just replaced my clutch few days ago and it engages at the very floor when you’re trying to release is it normal? it doesn’t feel like it’s a OEM or close to OEM

Hey, so I just got my flywheel resurfaced and they said one of the dowel pins broke in the process. It is the stock flywheel and I was wondering if it is fine for me to use. Or it's risky. The car is a daily driver and I am putting in a stage 1 and probably will be doing light racing.

How long does this job usually take solo?

How hard is it to find a K20A and 6speed in good shape want to I install in my base

Bro hook the guy up with some wheel cleaner lmao it pretty bad down there

you did not show us which bolts/nuts to work on... we just learned that you already put down the transmission

that bread part, you didn't show that it got remove... you cut the camera then showed us it has been removed already... why is that?

Got a clutch and flywheel replaced but now a trans light came on, have you ever gotten a trans light after replacing a clutch/flywheel ever?...thanks in advanced

Bread .. who knew

Bro you should get full cat back toda and headers🤓🤓🤓

You did a lot of stuff you didn't have to do bro. lol I should've made a video of my Exedy Stage II install.

Can u do mine

Damn you didn't change the rear main seal when you're in there?

can we use something other than bread? My car is gluten free.

Can you do my clutch for me

Re: "... I'm pretty much an hour sex guy... " on index 25:36, is that what you said?

Too complicated lmao, I rather pay a shop