How to Install K20 / K24 Clutch EP3 / RSX [step-by-step]

Рет қаралды 27,470

5 жыл бұрын

In todays video I show a few tips and tricks on my competition clutch install on my k24a2 ep3 civic. The process should be very similar with any K series engine in a ep3 or RSX.
JDModsgarage
SUBSCRIBE for awesome weekly car videos! Anything from how-to videos to racing to vlogs!
* We are not certified mechanics. All projects show in our videos are done at our own risk and we do not recommend repeating them without consulting a professional. We are not responsible should anything happen to you or your vehicle if you choose to repeat anything seen in our videos.*

Пікірлер: 37

@1_Bad_Z Жыл бұрын

Interesting. I took my 2005 Civic Si EP3 to my shop couple days ago. Was told that front suspension needs to be pulled to access clutch. I was @ around 10% clutch left. I'm getting an Exedy stage 1. Should get it back next week. Can't wait.

@Enkor528 Жыл бұрын

i'm in the same boat as you! also gon' roll stage 1's/

@anestiskariotis2728 7 ай бұрын

Great video bro! Just wanted to say thanks for the clutch bypass by bridging the leads of the connector! Been looking for this info and luckily stumbled across it in your video.

@steviemichelle7271 3 жыл бұрын

Take such and such “ewt”. Omg this makes me miss my Canadian friends 🤣😭😭😭 Thank you for posting this!

@YoungGearHeads 3 жыл бұрын

Thanks for the info, we are inspired to make a similar video as we need to do this job also.

@Slurpinsoup 3 жыл бұрын

You never showed where those bolts went for the Mount, but I believe I found it. Im doing mine as we speak

@UYC. 3 жыл бұрын

Great job

@eclxviimerx7588 5 жыл бұрын

Thank you so much I have to do this to my rsx this weekend now I have a way better idea this should be a breeze

@jdmodsgarage 5 жыл бұрын

Yeah is really not that bad just take your time and torque the bolts properly and you'll be fine!

@HHIVR4 2 жыл бұрын

You can realign the axle if the U joint seperates at the axle cup.Pretty easy.Just make sure the boot doesnt get torn.

@miguelnieves9915 3 жыл бұрын

Was it hard to remove the starter without removing the intake manifold?

@eslameddinghalebi1 5 жыл бұрын

Hey how long until the turbo pulls?

@reza_dc2 5 ай бұрын

did you have to remove the starter?

@AR-ep6ib 3 жыл бұрын

Did you need to bleed it up after??

@G1bson258 5 жыл бұрын

Any videos on how to replace the Slave cylinder or master cylinder on the ep3, drive one today clutch felt spongey

@screwdajuice 3 жыл бұрын

Remove your intake housing, unclip/unbolt the clutch line running above the transmission, remove the two bolts holding the slave cylinder. Undo the line going to the slave cylinder (10 mm) and replace it.

@honda123456g 4 жыл бұрын

Quick question, when pulling the transmission off do any of the dowel pins fall out or come off either from the bell housing side or the engine block side?

@jdmodsgarage 4 жыл бұрын

Nah they kinda just stick to where they are. They are press fit for sure

@mylessackett489 2 жыл бұрын

Hi mate, did you have trouble with the clutch travel with the competition clutch? I have seen forums of adding a washer to the clutch release fork ball joint to allow for a higher biting point on the clutch. I have installed 2 of these and the bite point is to close to the floor, even when the rod is adjusted to maximum travel

@jameswiedman8379 Жыл бұрын

I run a stage 2 comp clutch and it just failed. Was always squishy as hell from the install then on. And like you said had to be pressed too far to get it to disengage. Now mine won't disengage. Time to remove and replace.

@jemy1971ify 4 ай бұрын

2.4 on your si. Damn. I wanna do that to mine. I just don't know how

@YoungGearHeads 3 жыл бұрын

Dam man, where the hell do you find a phone book these days?

@VIPATOOB 5 жыл бұрын

Hello I was wondering if you can tell me how to fix my left head light, on start it doesn't turn on I have to drive it a while to start it has gotten progressively worse. I drive an 02 rsx base silver