RSX Type S Clutch Replacement ! (Step by Step)
Рет қаралды 41,969
4 жыл бұрынFollow me on IG @dennis_behrend98 👇
www.instagram.com
Stage 1.5 Competition Clutch 👇
www.kseriesparts.com/CC-8037-...
Competition Clutch Light Weight Flywheel 👇
www.kseriesparts.com/CC-2-800...
Honda Super High Temp Urea Grease 👇
www.alldiscountparts.com/oem-...
Honda OEM Throwout Bearing
www.hptautosport.com/products...
Honda OEM Pilot Bushing 👇
www.partsgeek.com/gbproducts/...
Feel Free to Comment Below!
@rudy5360 4 жыл бұрын
Best DC5 clutch video on KZfaq!
@jdmdennis9763 3 жыл бұрын
Thank you!
@Adam-kz8jn 3 жыл бұрын
Nice work man. Love the angles and love the walkthrough. I just got my rsx and I feel confident enough to tackle this job. Thank you
@nilssvensson3786 2 жыл бұрын
I have a 02 honda si. The stage 2 clutch that I hade on broke on me. I watched your video like a billion times and replaced it myself with a stage one. Thanks man fr!!
@Codi3000gt 3 жыл бұрын
Dude this video was super helpful. I'm about to put my trans back in.
@chadwickwicky67 2 жыл бұрын
Thanks for the vid man! definitely gives a diy a good idea of time frame and what’s needed + what should be replaced while doin the job that may be overlooked.
@dan8lim Ай бұрын
Super detailed step by step instructions. Makes me more confident on replacing my clutch if I ever have to do it down the road
@logantimberman3553 Ай бұрын
I love this video breaks everything and actually shows how to do everything very helpful and encouraging will be doing this my self soon thank you
@ALYang559 3 жыл бұрын
Yup oem throwout bearing is the best of the best.
@crz666 2 жыл бұрын
Awesome video. I will be doing my clutch this week. Thank you!!!! Subbed!!!
@Dear-_-Agony Жыл бұрын
How'd it go?!
@crz666 Жыл бұрын
@@Dear-_-Agony went great. Thank you, appreciate your video!!!
@JeffReams 3 жыл бұрын
That's a nice jack you got ... I got the same one :)
@mckoylach1622 3 жыл бұрын
Nice video,bro,thanks...
@broke2bewealthy616 3 жыл бұрын
You did great on this video it help a lot but in future reference try not you a hammer cause metal isn’t the best try to use a Mallet but once again this video was great much appreciated
@asdfasdf-rb3oq 2 жыл бұрын
clutch disk actually looks fine. The tolerance is the rivets
@jordan_.zx10r 3 жыл бұрын
Do you have a to oil the new main seal or just put it in?
@kongchan916 3 жыл бұрын
Oh man this is good stuff. Idk if u scared me off but Sheesh that's alot of damn work smh. Makes me wana pay someone now lol.
@C43Luis 4 жыл бұрын
Keep it up!
@jdmdennis9763 4 жыл бұрын
Thank you!
@randywardle4406 4 ай бұрын
Thank you! great video! What were the torque specs on the flywheel and pressure plate?
@dutchmenmodsandrepairs1427 2 жыл бұрын
Great video! Where did you get the clutch alignment tool? Do you have a part# for it?
@ChiicoK3lly 2 жыл бұрын
Thank you
@UYC. 3 жыл бұрын
Great job great content stay safe peace....
@Le_Papa 3 жыл бұрын
Just subscribed :-)
@masonmoua6833 4 жыл бұрын
Nice content
@jdmdennis9763 4 жыл бұрын
Thank you!
@McRib47 4 жыл бұрын
just a heads up i believe honda recommends when torquing down the flywheel bolts do it in 3 parts. JUST FYI
@jordan_.zx10r 3 жыл бұрын
What order?
@McRib47 3 жыл бұрын
@@jordan_.zx10r as in dont torque to max torque in the beginning split in 3 steps, 1st torque all 8 to 20ftlbs then 2nd time 40ftlbs and last 85ftlbs last round should be the heaviest as honda recommends according to the FSM. dont quote me on the number of ftlbs this was just a reference so go according to FSM.
@jordan_.zx10r 3 жыл бұрын
@@McRib47 I think it’s 90ft lbs for rsx I’ll do what you said
@angelmonroy9644 Жыл бұрын
@@McRib47 why
@gioraya9094 7 ай бұрын
By any chanse you have the part # for oil seal bearing!! Thanks!
@josebenitezlopez8802 Жыл бұрын
what’s the clutch alignment tool kit for?
@yoshihd326 Жыл бұрын
Did you say 19lbft or 90lbft for the torque wrench?
@prcc8793 2 жыл бұрын
Nice video,im planning to do this soon.what brand is the flywheel and how much is weight
@ryandownsbitch 3 жыл бұрын
Did you use a hoist to put the trans back in currently doing mine right now
@jdmdennis9763 3 жыл бұрын
Yea I used engine hoist to put my transmission back in
@josebenitezlopez8802 Жыл бұрын
where do you get all of the torque specs?
@xavieromar1123 3 жыл бұрын
give me the torque specification of each of the parts?? Please
@Zaberdutton Жыл бұрын
The one part I came to see was the only part that was skipped over and that's getting the transmission shaft back in and aligned properly...
@TheMigs87 Жыл бұрын
Do you still have the CC Stage 1.5?
@Nikko-zi3ti 2 жыл бұрын
when the pilot bearing is seated should it be able to spin or no?
@masumoto007 Жыл бұрын
Supposed to stay seated😉
@joshuapohl2990 Жыл бұрын
What did you use the Jack bar for the big breaker bar?
@CitiZen1.0.1 27 күн бұрын
On the crank so it doesn't spin on the other side while he torqued the flywheel bolts. (I think)
@87emagdnim 3 жыл бұрын
What did you use to keep the engine level
@timetokillslapp 2 жыл бұрын
I'm doing it right now bottle jack with a piece of wood on oil pan
@aycarambas 3 жыл бұрын
Aw man you left out the best part how to reinstall the transmission. I used a jackstand but it was a bitch trying to line it up. Very labor intensive!
@droptopp3479 3 жыл бұрын
yehh i thought the same too lol, i did mines 2 months ago and man aligning the transmission back in was a pain. Took me and 2 other ppl 1 whole hour while bench pressing tht thing cuz jack wasnt angling right.
@aycarambas 3 жыл бұрын
@@droptopp3479 Whats your secret? Any tips? I just kept wiggling with 2 people above and a jackstand underneath until it slowly lined up with the guides. Took like 30 tries. But it was such a pain no joke for a minute I thought about junking it and getting a new car.
@droptopp3479 3 жыл бұрын
@@aycarambas lol well first dont mke the mistake i did, which was if trans doesnt go in then try sticking the alignment tool back in to see if it actually goes in smooth. So after like 20min it didnt work so i tried tht and saw tht the alignment wasnt too straight so i had to redo align and straighten up the middle by pilot bushing. Then after tht, we just pushed it in while hving 2 guys under the trans bench pressing it and one on top to push and align the trans. After wiggling it counter and clockwise for 10-15min it finally went in. Using cherry picker wouldve been the easiest way i see but i didnt hve one. Definitely do need 2 extra ppl to mke it easier on yourself tho. I didnt want to work on the car the next day so we had to get it in no matter what but yeh it was a pain in the ass.
@jdmdennis9763 3 жыл бұрын
A G Using engine stand and Jack really help to align the transmission back in. That’s what I did!
@Mrsmith1082 2 жыл бұрын
You can always throw that pilot bushing in a plastic bag with some lube in the deep freezer the night before and it will go in easier..because science.
@joel-je2bv 2 жыл бұрын
hey man, gonna start working on my rsx very soon gonna use this as reference hope i don’t fuck sum up
@papoportillo1019 3 жыл бұрын
What are the torque specs for bolting the trans back to the engine ??
@kristianjon4014 4 жыл бұрын
First
@ReefyBmx 5 ай бұрын
Lets do a rsx type s meet again.
@dropperknows3390 3 жыл бұрын
wow that oem clutch looks bad! How many miles did you have on the car before you changed it? I currently have 82k on my 2006 type s & nothing feels wrong with mine at all. Just want a lighter flywheel and stage 1 clutch
@Kseriessuck 3 жыл бұрын
Stock one isn’t really all that great tbh, im on og clutch at 110k with fbo, reflash and it’s locking me out of gear and slipping, ill be putting in an exedy stg 1 with lw flywheel
@bobbutler1240 3 жыл бұрын
Does the starter need to be removed
@seanneuhaus8115 3 жыл бұрын
No you dont
@urielortiz3667 4 жыл бұрын
Why did you choose this clutch kit over the exedy? Also, can you explain why yo i replaced the pilot bushing and the throw out bearing? I’m replacing my soon and can’t find any info if those two parts are needed to be replaced while replacing the clutch
@jdmdennis9763 4 жыл бұрын
I choose competition clutch because my buddy has one and it felt great. I replaced the pilot bushing and throw out bearing because over time it gets worn out. I highly recommend replacing them while you are at it or you might have to take the transmission out again. If you need those parts I would go to your local Acura dealership and get it there, it wasn’t that expensive. Also both competition and exedy are great brand I would definitely recommend either one.
@urielortiz3667 4 жыл бұрын
Dennis Behrend oh ok, thanks for clearing those things up for me definitely going to swap them out while I’m at then
@urielortiz3667 4 жыл бұрын
Dennis Behrend Thank you. I ordered and got every thing that you recommended. Definitely excited to see how it is after the swap!
@jordan_.zx10r 3 жыл бұрын
@@jdmdennis9763 is the CC TOB not good?
@jdmdennis9763 3 жыл бұрын
JCBR600RR Always use factory, OEM throwout bearing. I heard from lots of other people that their competition clutch throwout bearing has failed.
@lunser9098 Жыл бұрын
My clutch just shit the bed, let’s see if this will give me some insight
@jimmyle4862 3 жыл бұрын
Nice video Dennis, what brand was your old OEM clutch kit?
@jdmdennis9763 3 жыл бұрын
Yea the old one was OEM
@jimmyle4862 3 жыл бұрын
Did you have to adjust your clutch pedal for travel?
@jdmdennis9763 3 жыл бұрын
Jimmy Le no I didn’t. I like low biting point on clutch.
@jimmyle4862 3 жыл бұрын
Cool, thanks man!
@Coldology 3 жыл бұрын
Why you’re intake look like mine the same exact even the ugly ass intake filter lmao 🤣
@jordan_.zx10r 3 жыл бұрын
Do you need to mark the subframe bolts removing it?
@JeffReams 3 жыл бұрын
The tech manual says that you are suppose to mark them, yes.
@jonathanlopez2338 2 жыл бұрын
you really gotta put that much grease ?
@steveswanson2294 2 жыл бұрын
Dude, a claw hammer to put the pilot bearing in? Lmao
@TheShangralaaaa17 2 жыл бұрын
slave cylinder.....its a slave cylinder
I Do Cars
Рет қаралды 197 М.
AHC Garage
Рет қаралды 21 М.
Мотомалышка Алина
Рет қаралды 6 МЛН
Thoy Chomnan
Рет қаралды 12 МЛН