Thank you.

Yes! Please do this

They will be getting ported.

kzfaq.info/get/bejne/ZqygaZp4stzSZJs.html

Most cost effective option for sure.

@@dynojoemods2764 13200 RPM MAX IS OK 372 XP OE?

I used the Echo top handles in the past and they were good units, The Stihl is also good, it does have more power and built a bit better in my honest opinion, I am not biased. I never tried the Husky top handle but I do have several 372xp saws and I like them.

Nothing wrong with that at all

Very popular top handle.

Thank you

Ported 2511 is pretty much where these bigger saws are stock/muffler modded. Just a touch less tq

Why does everyone port saws there ain’t going to be no good saws left they all are going to be hacked up

Thank you!

Appreciate it

I agree Doug!

Will be fun to see the gains!

@@dynojoemods2764 @Paveen Raj my 355T absolutely rips! Jereme Bell did mine. Tube type muffler mod, ported, and timing advanced. You can see on his KZfaq channel my saw versus a 201T a year ago.

kzfaq.infohistory

@@dynojoemods2764 kzfaq.info/get/bejne/ZqygaZp4stzSZJs.html

kzfaq.info/get/bejne/ZqygaZp4stzSZJs.html

That is what I have heard. I will try and get all the "brand new" ones next time. These seem to be the most common ones used today. But can still be tough to find

Might have to try sometime

@@dynojoemods2764 yes please do this. I want to know how much power the new electric saws have

Definetly the Echo rear handle battery saws. They feel way stronger than husky and stihl.

Thank you. That is the plan to get them all ported and back on the dyno

@@dynojoemods2764 That's a boy! Merry Christmas to you and yours.

@@Andyshine77 Thank you Merry Christmas to you and yours as well

@@Andyshine77 kzfaq.info/get/bejne/ZqygaZp4stzSZJs.html

Thank you

I'm also curious to see how a 435t sizes up since that's the one I use every day at work

I'll have to see if I can track one down. Hope you and your family are doing well. Glad you found the channel, hope it can help with saw performance info.

@@dynojoemods2764 I have one you could test if you can't find one. Same to you and your family!

@@jaredeberly9724 I have 3 that I ported they will out cut my 540s. Can't do whole lot with compression. But little goes long way. And lots of room for improvement on transfers and exhaust port. Just don't raise the exhaust at all. I widened and reshaped the intake and rased the bottom few numbers. Its mind blowing stout. I port matched the exhaust to muffler.Closed of the tube. I use cut off deep well sockets on my custom exhaust so I can change the diameter and found 11 mm is the ticket! Cut whole in plastic have exhaust come out under the bar.

Thank you. I will try and keep a steady flow. I do have a few other things I want to incorporate along the way

Yeah that would be awesome to see that testing done with 572xp an 462cm I can't wait to see results 😊

I agree. The last few saws I have had dropped off were from tree guys, and already muffler modded. I will get 100% stock versions eventually. These were all simple diy type mods.

I will certainly give that a try on the next video showing more than 1 saw.

I'll try that sometime

No fuels tested yet.

Could be a possibility. Not sure what would happen to the plastic around that area

20g mild and also offer a 20g stainless

Thank you. Appreciate the help I really should dial in a content schedule. But I tend to get side tracked and hit left field really quick before getting back on track... I did see a cheap Subaru in town the other day.... hmm....

It’d be fun watching 😁😆😂😜

Soon. Need to dig the equipment out and make sure it still works and if I remember how.... It's only .120/3mm wire and 600 amps. But plenty toasty

Thank you. I like Amsoil Dominator 40:1 That is what I have been using the last couple of years.

@@dynojoemods2764 thanks joe for the reply !! Ive been wanting to try something new for 2022 and i think amsoil is going to be the ticket ive heard about saber but im not so thrilled about the 100:1 ratio ! If dominator is what you like then who am i to argue you're the one with the dyno !! Thanks again joe you rock man 🤟👍👊👋

@@elbenny805 Most all of the newer synthetic oils work well at 40:1. I just like what I have seen from dominator I'm these saws. So I stick with it.

@@dynojoemods2764 that's a big 10-4 there partner 🤠 not only do you seem real knowledgeable in this area but i can tell you're the real McCoy when it comes to your stuff ! speak of it no more joe 40:1 on amsoil dominator it is right on the edge of lean thanks again joe i greatly appreciate your time ill be setting that lil bell 🔔 till the next video drops keep em coming partner 👍👊👋

Should be very close. I think the 620 is heavier though. Ported all out, the 361 may be a touch more power but it should still be close.

My 362 stock blows my brothers stock 361 away. I was 😲, maybe I should give it a closer look when it’s on the bench for maintenance.

I have an old Super 2. Still has great compression. I should try to get her running some day.

No, I have not. Actually not ever seen an 009. Sorry.

Testing the durability I see.... The one I have may have come from your company lol. Appears to have hit the ground a couple times.

Lol they can get aggravating. I don't even pull it without choking it anymore. 🤣

Each to his own I guess. I would like to try one of those Echo 2511t saws though just for the reduction in weight.

@@treemerc101 Ported 2511 is about the power of these bigger saws stock and I believe about 2+ lb lighter.

@@dynojoemods2764 2 lbs is a lot less wear and tear on the body over the years. I really appreciate you putting the numbers out there for us. Keep them coming man

It was a touch fat at the beginning. These small saws I have to apply the load slow, otherwise it will catch and bog them out.

Probably not 100% fair. But all were simple 10 minute muffler mods. The husky was probably a 30 second mod. These were all just simple deflector/outlet mods.

I know what you mean, my friends husky 359 has a cat and we bypassed it and it really work up big time. Felt like it had an extra 30% more power.

What is crank walk?

It is coming. Before 2022. That is a hand full of saws to aquire. They are rolling in though.

@@dynojoemods2764 have you dyno'd a 462 with the Red Beard foam filter vs stock airfilter?

@@chrisp556 I did one of those, I think it was a 462. They did improve over stock.

@@dynojoemods2764 thx. I have a Straight Shot and bn wondering if the foam filter showed an improvement on the dyno. Awesome channel Joe

I kind of know how it's going to go with 572xp and 462cm comparison 572xp has more grunt down low other then that they real close I have a heavy muffler mod on both does real nice getting heat out an power gains can't wait to see the results

4.14 kg for the echo 4.28kg on the other 2

@@dynojoemods2764. I actually meant in real time on the videos if possible. Loving your work and the channel. Growing nice and fast.

@@Alan_Hans__ Thank you. I will try and do that on the future videos. Or at least put the conversion up in text format. Thank you for bringing it to my attention. I often forget this is a worldwide platform

That was smoking bar oil. The exposed muffler on the bottom of the 540 was smoking on the rubber pad.

@@dynojoemods2764 ok that makes sense! Wasn't trying to offend just seen smoke and the rest of the saws didn't as much ha ha anyway great work thanks for the reply

It has some use for sure. I plan to get cash models and the 200t and do the test all stock

Also the discolored plastic around the clutch, I'd like to see another test with a fresher one. The reason I bought mine a long time ago was it beat the 201 stihl hands down before stihl was m tronic.

Stock the 2511 dosent hang with these bigger saws in power output. But ported 2511 is right up close to this power level and a few lb lighter saw

I'll have to pick one of those up.

Only a few tanks through the echo 6-8 through the 201 and looks like a lot in the 540.

@@dynojoemods2764 Thanks! In your experience, do saws that are broken in gain some power?