Here are the torque specs from the service manual: Bushing clamp (2) - 22.1 ft-lb Endlink (2) - 28 ft-lb Lateral link 17mm - 59 ft-lb If you don't torque correctly, it will CREAK !!

Been following your building since day one, you are definitly making me want a '15 wrx even more. Great videos!

From the Whiteline install PDF Caution: Always start with softer setting rather than harder. - Always use new hardware if supplied. - Tighten all fittings with the vehicle at ride height

Pull the end links off with the sway bar if you're going to be replacing them. They can be a pain to remove if you have some milage on the car. Also, this should be done with the rear suspension loaded at your planned ride height. Back on to some ramps... It works really well, just make sure the ground is even.

This video was amazing in detail, thank you!

Finally got mine installed on MY16 today this video was great thanks alot

Thanks for the video. Was really helpful every step of the way

The Y pipe (exhaust) can get in the way of the rear Whiteline Sway Bar. You may need to remove it, easier if you have an Invidia installed. The stock might be a PITA.

Great video, very professional!

Nice looking bar

Another awesome video!

I have this set up on my 08 sedan wrx and boy it really keeps you glued to the ground.

Sorry if this was covered, I didn't see it in my scanning. But aren't you supposed to put the weight of the car on the suspension to settle the bushings before you tighten and torque them?

Do you guys have a video on how to put on the front strut tower brace?

This is 1,000,000 times easier if you drop the exhaust like SubiSpeed did.

also, what is the torque spec for all the hardware?

I noticed you install what appears to be new bushing brackets. I'm curious what brand they are or if they come with the bar kit. The current kits from whiteline (bsk018 specifically) doesn't appear to come with those new bushing brackets.

how much torque is required on those bolts? same goes for the strut one. Just curious if it's a certain amount, of just by feeling

If I install these front and rear sway bars/end links. Along with coilovers, dropping 1.5”. Do I have to change the length of the end links? Or keep them the same length as the oem

when you're installing the rear sway bar/end link does the car need to be on a loaded suspension? or can it just be up on jackstands?

is it ok to fit coilovers first and then fit everything else after wards? or get everything together then align?

Is this the best option for the WRX to experience more oversteer than understeer? Thanks!

In this video is that a 22mm sway bar? I know Whiteline now has several versions you can get.

what are the torque specs for all the bolts? also shouldnt they be torque with the car with load?

What size sway bar did you use?

Hello do you have to remove part of your exhaust? Thank You

Do u need an alignment after installing?

Has anyone tried the soft setting on these bars? If so what was the reult?

How does the medium setting compare to stock ??

What size sway bar is that? 22mm or 24?

would this be fairly similar to the 2008 sti? i'm assuming so.

That compatible with my Subaru forester XT 2015?

did you take them apart and put grease in the links?

Can you install the rear sway bar with the car sitting on the ground?

will this fit a 2015 forester xt

did you guys buy the base model wrx?

Are the bushings really greaseless? I've read that they now require grease because of noise after being installed for a while.

Where is is the link to the end link on your website?

Should have held both ends stationary and adjusted endink with the gold adjuster. Equal threads.

Can anyone tell me what size those bolts are? Lol I can’t find it online and need to replace one of mine. Thanks

can one install new bar on ramps or is it recommended to with suspension unloaded say using jacks?

Bro, you wear your watch while working on the car? I'm surprised the watch band isn't covered in black grease yet! 😅

Nice crown and buckle watch band! hahah

Why does no one talk about the booklet instructions from whiteline showing that spacers must be added together in order to shift the centerline at the LCA side of the end links? In theory not doing so would apply a partial lateral load on the LCA instead of just perpendicular. Am I the only one overthinking it? It would be really hard to shift the end link center bolt sleeve, pretty much requiring a bushing press every time you want to shift between Low,Med,High levels. Has anyone had issues because of this in the long run? 🤔

This video was my savior! Thanks! they include a bunch of Extra washers…what are those for!? I didn’t see this video use any so neither did i

The little side locks you guys added at the end was that included in the sway bar kit or is that sold separately?

What are the torque specs for this install?

Is it

Is there a difference between the WRK and the STI sway bar? I understand there was quite an improvement in the suspension of the '15 suspension and I'm wondering if this will really be necessary for my STI Launch Edition.

Is the Whiteline end link really necessary if I don't do track? And if I'm only using 20mm? (just trying to save some $ if it's not necessary)

does all this come with the sway bar on your website or are they sold separately?

What do those red pieces of plastic on the endlinks do? Are they just a protective cover for the rubber? I noticed you installed without them.

I still wish you were the guy that does the install videos. Easier to go point by point on ur explanations

does the softer setting give you more or less oversteer?

where can i get the gold support bushings for the endlinks? i cant seem to find them on your website

What are the torque settings for each bolt?

Somehow my endlinks didnt come witha 14mm bolt, so when I try to put the 17mm on it just constantly spins...wtf

Could someone assist with the torque specs. Thanks!

Is the softest adjustment for the Whiteline more stiff than the OEM?

I seemed to miss but, what is the mm of that Whiteline rear sway?

what size are the bracket bolts and endlink bolts? I really need to find the correct bolts in order to install the bar

Hey what kind of wheels are those?

What is the purpose of brace??

What wheels are those??

Man those Rs3's are bald

C as was

Them tires are almost gone lol

Change those tyres while you are at it dude.......

Tires looking kinda bald there

Put some goddam grease on your threads ! ;-)

I just took the entire bar off with the endlinks still on the bar LOL

Another video with no torque specs...

Or you could just put a small load on the suspension by using a jack so the end links aren't maxed out... but, I know, fuck me, right? lol Seems too simple...

No torque specs, no grease on bushings, no measurement matched endlinks, not even correct procedure to avoid pre load. Horrible tutorial.