NC's are the real sleeper Miatas imo. Great performance platform!
@Nasonix2 Жыл бұрын
Absolutely. They have much more potential for a competitive track car than the earlier ones. I can list some features off the top of my head. - Multi link rear suspension opens up anti dive and anti roll geometry. - can fit MUCH larger wheels and tires without even rolling the fenders. - 10x17's fit with minor fender roll. No need for cutting and adding flares. - much superior engine. All aluminum, handles a decent amount more power than the earlier cars. - fully stock engine, stock cams and valve springs can rev to 8,000RPM for extended periods reliably. - always comes with vvt-i. - NC 6speed transmissions hold more torque than the na/NB 6spds. :) - beautiful forged aluminum front control arms. Don't have to worry about rust as much. - much more rigid chassis. You can literally add every chassis bolt on for the na/NB that's available. Roll bar, frame rails, frog arms, butterfly brace, diff brace, etc and guess what... The NC will still be more rigid AND at that point, it will be lighter. lol - power retractable hard top as an option. Nuff said ;) oh and heated seats IN A MIATA! - traction control on/off button. - ABS brakes standard. - OEM radiator is a cross flow design. You know how much it costs to get a cross-flow radiator in an NA/NB? Just look at supermiata's cross-flow radiator. Thing is costly!! - the ability to tune/flash the stock ECU. Saves time and money from needing to use a standalone ECU. - the NC also comes with a wideband sensor from the factory. More cost savings. - lighter wheels, less unsprung weight. - the timing chain is self maintained by oil pressure. Never needs replaced. - the oil pump is different, doesn't need to be upgraded to avoid splitting gears. - 2.0l aluminum block > 1.8l iron block. Lighter, better cooling, and last but not least. The rotating assembly is strapped down with a crank girdle plate. No more individual main caps to split when spinning high RPM or high boost. Now folks those are just some reasons off the top of the head for why the NC has the most potential for a competitive sports car. The NA/NB will ALWAYS be amazing in its own way. It's probably the most enjoyable car to drive from a pure enjoyment standpoint. Lighter out of the box, extreme aftermarket support in every category, theyre great cars. classics. Not trying to take anything away from them. I'm simply saying the NC is no boat haha. It's actually the opposite
@Rust-eze9992 жыл бұрын
“Gettin real good at this gonna come in handy later” 😂😂
@vlenhoff Жыл бұрын
Check the state of your clutch pedal assembly. Mine cracked after my stage 1 clutch and light flywheel install. I love the results, but that cracked pedal drove us nuts.
@pattyboi2 жыл бұрын
Planning to do a roll bar in the future? Probably picking up an NC with PRHT and am interested to see you handle the process
@ZentRose2 жыл бұрын
Yeah I think we only have one option though. Have you done any research?
@pattyboi2 жыл бұрын
@@ZentRose Yeah there's one Hard Dog on Flyin Miata for a PRHT that let's you keep a lot of the interior/roof functionality, doesn't have the angled bars for more support though. I have another Hard Dog on my NB and the fitment was great. Hopefully this is good as well, was probably planning on doing that in the future.
@ZentRose2 жыл бұрын
Sweet, I'll take a look at it. It's probably a lot better than the factory hoops
@TheCorington2 жыл бұрын
dont get a prht if you plan on making it a track car. the rollbars are lower. Will be okay for HPDE but not for any SCCA/NASA competition. It's also heavier by about 100lb.
@paulbfields82842 жыл бұрын
More smiles per mile in an NC.. with goodies..
@jackandcoffee11452 жыл бұрын
You should look into doing some 'make sure you enjoy your car' merch. I'd buy a shirt and/or stickers.
@ianfairbanks13182 жыл бұрын
Absolutely. I'd buy RN
@printedprops87302 жыл бұрын
If you havent already, put Ford motorcraft tranny fluid in it. Did that on my NC and shifts smoother! I also used to have an issues sometimes going from second to first, not anymore.
@Johnkillaman2 жыл бұрын
I just put in Royal Purple Gear Max and I'm having great results compared to the 3 year old motorcraft fluid
@andusensei2 жыл бұрын
I just bought this clutch kit cause I'm on a budget, and I'm now just seeing this video. Thanks for the video, my fears of it being a horrible ebay clutch are quelled haha. I wanna diy it but I'm wary.
@ZentRose2 жыл бұрын
This would be the car to learn on for changing out a clutch. It is not a bad job if you have the extensions, transmission jack and bearing puller. Also, with the ebay clutch kits I have had the bearings fail within 10,000 miles so I like to buy OEM bearings. Good Luck
@Birb_of_Judge7 ай бұрын
Honestly, the only bearings i would buy with confidence are SKF
@fillj2011 Жыл бұрын
Am I the only one who got chills seeing the absence of jackstands???
@fillj2011 Жыл бұрын
Just saw them 😆 good and informative 👍 btw
@wurstschnecke77309 ай бұрын
did you have to loosen the starter to get the transmission in and out?
@tylermiavlogs5441 Жыл бұрын
I have a miata nc the platform is amazing but aftermarket support isnt there….. yet
@brian-wk4yr2 жыл бұрын
What clutch kit is it?
@adamwest5192 жыл бұрын
How well has the clutch fared? Debating going ebay + oem or high quality aftermarket bearings but unsure
@Dyltheboy7 ай бұрын
Have you decided? If so how’s it going?
@adamwest5197 ай бұрын
@@Dyltheboy I used a flyin miata stage 1 kit. Worked good for about a year until I wrecked the car. OEM feel and bearings were in great shape
@Dyltheboy7 ай бұрын
@@adamwest519 damn, how’d you wreck?
@adamwest5197 ай бұрын
@@Dyltheboy deer jumped out in front of me, I swerved and hit a guardrail head on
@gz617 Жыл бұрын
So there is so much debate about clutch chatter online. I got an Exedy Stage 1 clutch installed with OEM flywheel along with OEM everything else and the chatter at low RPMs in all gears is awful. Some say lighter flywheels cause this, others say not getting the old flywheel machined is the problem, etc. etc. I guess my question is did you experience any chatter with this new setup? Without applying any throttle, in first gear or even reverse for that matter, if I slowly release the clutch there is so much chatter and it really doesn't seem to like it, everything starts shaking before the car gets enough speed for me to completely release the clutch.
@ZentRose Жыл бұрын
Gear chatter or engagement chatter? This clutch was pretty terrible with chatter, I switched out for an ACT disc when I swapped the engine and it's all good now.
@gz617 Жыл бұрын
@@ZentRose Well it will chatter as I am trying to engage as well, but even at low RPMs on higher gears I hear all the way up to maybe 2-3K. As RPMs increase it goes away, its most noticeable at lower RPMs, and especially if I attempt to release the clutch without any throttle. That is when it makes the most chattering sound (basically lowest RPM possible). I recall being able to get cars into first gear without any throttle just slowly releasing the clutch but with this car I don't even risk it because the chattering/shaking gets so bad
@paulhughes39612 жыл бұрын
I'm slowly upgrading my NC but for some reason I'm not able to find a chrome gas cap and trim ring for mine. Where did you get yours at and I would appreciate a link. Thanks!
@ZentRose2 жыл бұрын
It came on the car but I think if you search "nc Miata chrome fuel door" you will find one
@2boosted3852 жыл бұрын
Do you have a product link list? I’m in need of this whole system
@john_dee14312 жыл бұрын
Thanks! About to do this too. When dropping the transmission, did you need to support the engine? Haynes is saying to but I don't find that advice anywhere else.
@ZentRose2 жыл бұрын
No need to support the engine but definitely support the transmission when unbolting the power plant frame! Wobble extensions and the pilot bearing tool made this job super easy. Good luck!
@john_dee14312 жыл бұрын
@@ZentRose Appreciate it and good luck on the track!
@gunny14022 жыл бұрын
Great video, thanks! So did you keep your old lightweight flywheel or did you use the new Ebay one? Whenever you get a chance, can you please make a list of the pilot bearing puller and the clutch kit you used for the video? It will certainly help. I'm about to tackle this job for/with a friend on his 6 speed NC and when I mentioned Ebay sets he thought I was joking! Thanks!
@ZentRose2 жыл бұрын
I used the ebay flywheel. www.ebay.com/itm/133337525966?hash=item1f0b892ece:g:e0UAAOSw2bReS5hq The bearing puller is from harbor freight: www.harborfreight.com/slide-hammer-and-bearing-puller-set-5-pc-62601.html
@gunny14022 жыл бұрын
Thank you for the quick response! Please keep us posted and don't forget to make a follow up video on how the set performed, if anythinh changed, broke, etc. Your videos are super cool to watch, keep up the great work and thank you again!
@davidgori66402 жыл бұрын
@@ZentRose Hi, I am italian and I have a 2.0 NC Miata, I have seen this video and I subscribe your channel cause is very useful. I have a workshop so I will make this work myself. I only would know if the clutch is good or not. I would buy a stage 2 (heavy duty spring) clutch max and a lightweight flywheel from the same seller on ebay (clutchamerica). Is it worth? or OEM Exedy clutch is better? I would buy an OEM (or SKF) thrust bearing instead mounting that one in clutchmax kit, is it the right choice? I have seen another little bearing in the kit, i think is impossible to find out of a clutch kit, should i replace it with it (in the clutchmax kit) or searching something oem or better quality? Thanks a lot for your attention, you're tips would be definitley useful! Thanks again and best regards from Italy.
@ZentRose2 жыл бұрын
@@davidgori6640 I would use oem bearings for the pilot and throwout bearing (I just ordered them through the Mazda dealer). If money isn't a problem I would recommend to use an ACT clutch. The eBay clutch discs sometimes have a bit of clutch judder.
@davidgori66402 жыл бұрын
@@ZentRose Thanks a lot. I have searched an alternative to Exedy OEM kit also because of the price (here 410€ for that). ACT kits seems expensive too, surely very good quality. Thinking that ebay stage2 kit has a stronger reinforced pressure plate that maybe avoid judder... I don't know, never tried these kits. You have tried the stage1 (like OEM) and has it judder?
@phaselaser2 жыл бұрын
what tool did you use to remove the pilot bearing?
@ZentRose2 жыл бұрын
Harbor freight slide hammer bearing puller tool
@Kamal-me5cx2 жыл бұрын
Great job ! However no break in period before reving to redline ?
@ZentRose2 жыл бұрын
I just avoid launching and clutch kicking when breaking in the clutch
@sdlausen12 жыл бұрын
How do you go from an s2000 (multiple at that) to a Miata? Isn't that a huge downgrade?
@ZentRose2 жыл бұрын
To me they are very similar cars. I prefer the NC chassis, brakes, steering, suspension geo, curb weight, convertible top and daily drivability. The S2000 has a better engine and interior.
@sdlausen12 жыл бұрын
@@ZentRose Interesting! I finally drove an NC on track last year. Only mods were coilovers, slight drop, and wheels/tires. I admit it was slower but WAY more fun than my ap1 + s2k. So... an F series swap into an NC would be the perfect roadster?
@ZentRose2 жыл бұрын
Yeah, the NC really needs more power. I plan to tune it to see how much I can get out of it but an engine swap would probably be the best bet. Enjoy the AP1!
@H3LPIV3FALL3N2 жыл бұрын
Was that a stock clutch you replaced?
@ZentRose2 жыл бұрын
it was an aftermarket exedy with light flywheel
@atotalpro2 жыл бұрын
How is the Clutch Max clutch holding up?
@ZentRose2 жыл бұрын
it started chattering after 10k miles and a lot of abuse... so I threw an ACT disc in there with my last engine swap.
@ianfairbanks13182 жыл бұрын
and because of this video, i have subbed. I too have an NC. thanks for the content bro. Suggestion- the head cam makes me seasick...
@ZentRose2 жыл бұрын
Thanks for the sub!
@aeirsone904515 күн бұрын
Left cat for the environment? Down thumbed and no sub