Here's raw on site footage of how to plaster a ceiling and wall. Part 2 of 4 Enjoy watching and keep yours eyes peeled for more. For all your building material and tool needs pop to. www.tommysyard.com
Пікірлер: 35
@tj93827 жыл бұрын
Great videos mate. At last someone who shows how to do the corners. Top man 👍
@sevensurvival7 жыл бұрын
Nice job, thanks, respect
@michaelanderson66259 жыл бұрын
Good job!!
@VidzMisc9 жыл бұрын
good stuff lads
@zeljkodzakic37877 жыл бұрын
in my country we have white plasters... nice job!
@donaldneilanderson68708 жыл бұрын
HI TY , Thanks. I will check out your website for the materials. I am so glad I found your website. I will spread the word here in Brussels. Neil Anderson
@sharondouglas99457 жыл бұрын
Donald Neil Anderson
@maher86537 жыл бұрын
the best Vidio Isaw thank you very much
@stargateproductions7 жыл бұрын
Hey, great video guys, where I'm from we don't coat the entire ceiling just the joints and screws. I learned a few things though! We coat 3 times, the last being a scratch coat or skim to get additional fine scratches or damage! Cheers!
@EppingForest3049 жыл бұрын
very good
@tspirit997 жыл бұрын
"yeah, go make some tea" LOL
@CascaNaiobi7 жыл бұрын
How long do you wait before flattening in? Are there any signs to look out for?
@jaycutts80548 жыл бұрын
Have you tried the Speedskim yet? Flatten off in seconds , from Romford Tools, good vid. Jay , Margate
@gamblemadman8 жыл бұрын
Top lads
@TheLondonForever008 жыл бұрын
How long do you leave the first coat before smoothing it out. (sorry for the stupidness but never plastered before, I'm a chippie and decorator).
@Ollyop657 жыл бұрын
Hi lads, great videos. I want to re skim a bathroom wall that was tiled. I have removed tiles and adhesive and wall is clean. Do I PVA the old plaster first? I also want to do the ceiling which is painted do I PVA this as well? Cheers
@elsewho7 жыл бұрын
Ollyop65 you will need to PVA the old plaster first as it removes dirt/dust and creates a adhesive bond for the plaster. It the wall is anyway not even I would apply bonding before plastering. Can only imagine you are re doing the ceiling because of cracks or its stippled. If it's cracked you will need to solve the reason it cracked in the first place, e.g loose ceiling joists or slabs not correctly put up first day. If it is stippled remove the slabs, put up new slabs and plaster. Remember to plaster ceiling first and then walls. All the best.
@donaldneilanderson68708 жыл бұрын
I really enjoyed the batten and drywall videos and of course the plastering. I have an unfinished garage, can I simply plaster the inside walls (building block) ? Many thanks... Neil Anderson
@TommysYardchannel8 жыл бұрын
+Donald Neil Anderson Yes you can, first of all you will need to apply an undercoat plaster "hardwall" or "sand and cement" to the block work first, allow to dry and then apply the finish coats of plaster afterwards "multi finish"
@andygollings46498 жыл бұрын
sweet what size is that trowel?
@rocketagro647 жыл бұрын
just wondered if can put subtitles for deaf to see how it done
@dougwilz7 жыл бұрын
Can you plaster this on to sand cement render
@DrumRoody8 жыл бұрын
Reckon these blokes wouldn't mind a pint.
@dotdash65997 жыл бұрын
i'm not a plasterer, but i plastered every room in my house before i rented it ( i'm good with a float ) its ok not professional but it did the job, i only used one coat !!!! but if my one coat went from mini mesh to mini mesh i cant put a second coat on ??? anyway good video
@DeathWish927 жыл бұрын
Kevin webster PVA your already plastered walls about 70% pva 30% water and plaster again good luck
@rickvondelius74227 жыл бұрын
10+
@ouide0077 жыл бұрын
What is the benefit of all that plastering? I have seen some just doing the joints and it was ready for painting.
@ExtremeEn3rgy7 жыл бұрын
thats tape and joint, plastering the walls will last longer and look better overall than what you said, also better insulation in the room
@bobsieshow8 жыл бұрын
hey i have skimmed my ceiling but run out of multifinish cant get any until tomorrow so my first coat will be dry....what should i do...as the first coat is pretty rough
@TommysYardchannel8 жыл бұрын
+bobsy bobsy you should flatten it in as best as possible and then you will need to re apply a coat of PVA glue and then start again. There isnt any short cuts to a nice finish
@bobsieshow8 жыл бұрын
+Tommy's Yard omg ...all i can say is ...you plasterers have it a lot harder than i could imagine....its tough work..thems your plasterers...ha ah thanks mate just gonna have to face the music ...and get to it...
@Maghanashi7 жыл бұрын
It's true. Good plasterers make it look easy, but look at Brad. He's a bald stallion for a reason.
@nonyadamnbusiness98878 жыл бұрын
A 'mil' and a 'millimeter' are two entirely different measures. This guy is using them as if they are the same thing.
@lukepowell21738 жыл бұрын
A mil and a millimetre are definitely the same thing, UK adopted the metric system years ago, mil might be an old imperial measurement but in UK trades, mil is an abbreviation of millimetre. At least thats how I know it....
@paulshipp237 жыл бұрын
There is also a US English specific term, mil but it's not used outside the US and maybe Canada: "A unit of length equal to one thousandth (10-3) of an inch (0.0254 millimeter), used, for example, to specify the diameter of wire or the thickness of materials sold in sheets." But in the UK we use mil as an abbreviation for millimetre, nothing else.