How to Replace Front Window Regulator Assemblies 2003-2007 Honda Accord

Рет қаралды 19,947

9 ай бұрын

Buy Now!
New Power Window Motor & Regulator Assembly from 1AAuto.com 1aau.to/ia/1AWRG00558
This process should be similar on the following vehicles:
2003 Honda Accord
2004 Honda Accord
2005 Honda Accord
2006 Honda Accord
2007 Honda Accord
Tools you will need:
• Phillips Head Screwdriver 1aau.to/obsb/1AXAA00013
• Pocket Screwdriver
• 10mm Socket 1aau.to/obkY/1AXAA00017
• Trim Tool Set 1aau.to/oaim/1AXXX00006
• Ratchet 1aau.to/obJI/1AXAA00016
• Socket Extensions 1aau.to/obGp/1AXAA00015
• Duct Tape
• Gloves 1aau.to/oap9/1AXSS00048
• Painter's Tape
• Safety Glasses
• Floor Jack 1aau.to/oadb/1AXAA00068
• Jack Stands 1aau.to/oZN/1AXAA00065
• Pick 1aau.to/oTa/1AXAA00037
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 17

@TRQ 9 ай бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@michaelduenas1364 7 ай бұрын

What if my window doesn’t roll down at all 😪 how do I get to the bolts

@nogal2002 Ай бұрын

For those wondering how to get the bolts out in between the two holes without using the window switch to lower the window, I just manually lowered my window by hand and put tape on the window to hold the window in place so I could access the bolts. You should be able to freely move your window around to see the bolts

@timowens5870 2 ай бұрын

The whole purpose of the video is to change out the defective regulator. How do you expect someone to roll the window down to access the 2 10mm bolts?

@josephoneill3197 17 күн бұрын

One of the best "how to" videos on KZfaq. The contributor was very thorough and clear on what to do and how to do it. His instructions on reassembly, often missed in other video repairs was concise and helped in not allowing missed assembly and ensured the proper hardware to be looking for.

@billtracyanderson1372 Ай бұрын

Great video! Gave me the confidence to order the part and do it myself. Ours was siezed in the fully up position; we undid the bolts holding the regulator to the door anyway as well as the motor bolts. Once everything was a little freer to move, we were able to get a side-cutters in there (through the hole over the speaker) and cut the cable leading to the top so the window would drop. Just a little help in case anyone else runs into this problem.

@BatMan-hu9qu 21 күн бұрын

Window doesnt go down with a dead motor. Here’s how I fixed mine. With my window stuck in the up position I could only push it down a couple inches. I removed the rest of the bolts to the motor and was able to push it down far enough to reach one bolt. I used a small 10mm combo wrench I was able to feel the head of the second bolt and reach it with the loop end of the combo wrench. Although I could only make 1/4 turns, once it was loose I unscrewed the rest by hand. Careful not to drop the wrench or bolt inside the door 😅 After that everything else went well.

@OutcastCentral 4 ай бұрын

I installed the new regulator exactly as instructed, the window will roll up & down when I press the button, but eventually it'll just stop working, I originally thought maybe the window gets caught on something when going up & down, which it was at first but once I fixed that, I was testing to see if the window worked & it did for a few seconds than it just stopped working again. I'd unplug the regulator & plug it back in & it would work again but for a few seconds...maybe a defective regulator?

@jonathanbradley268 5 ай бұрын

Great video! Couldn't have asked for any clearer instructions. My son had been using duct tape to hold his window up until the part came. It took more time getting the sticky residue off than the installation. Thanks again!

@jameslee9191 5 ай бұрын

Best video instruction ever! I’ve watched many

@nikstah1232 Ай бұрын

Nice video man, me and my mate managed to swap my regulator for my Jdm cl7 euro r in about an hour and half, had its moments . But made it there in the end…