[Tutorial] Ondsel/FreeCAD VariableSet use for parametric design.

Рет қаралды 3,610

18 күн бұрын

#freecad #assembly3 #cad
Support my channel:
/ oficinerobotica
www.paypal.me/oficinerobotica
liberapay.com/oficinerobotica...
Download Ondsel/FreeCAD:
ondsel.com/
www.freecad.org/
This video sponsor:
www.justway.com/
Afiliate link:
www.justway.com/?from=Oficine...

Пікірлер: 26

@layer7io 16 күн бұрын

I found this to be an excellent introduction tutorial into Ondsel ES / FreeCAD. Thank you for your hard work!

@jc84com 17 күн бұрын

I do like the variable sets. Very impressive way to setup the document over sheets

@Improvement_gg 17 күн бұрын

I think you’re the best channel of freecad you helped me a lot

@daomingjin 16 күн бұрын

but the way people from finland speak so slowly and with their accent makes the video drag on. Not that i don't mind the accent, but i feel like the video is going way too slow as if i'm being talked to incredibly slow on purpose because someone assumes i'm retarded. LOL. good info though.

17 күн бұрын

Nice to see you again. Thanks!

@Skyliptor 15 күн бұрын

It's great to have you back, the video's great as always.

@AnthonyClay 16 күн бұрын

I've needed this so badly! I've actually had a really hard time dealing with variables to be shared across models (without resorting to multipart) in other CAD software. Usually, my go-to was to use excel spreadsheets to drive a design - but that had strange limitations. This looks basically like multpart, but does seem intuitive to use. Support for integer lists seem to indicate that configurations might be a *really* nice! I'm excited to try this out! Also: *finally* a linux CAD suite that's (maybe) ready for prime-time! I know freeCAD has been here a minute, but I just ...couldn't take the interface/breakage. Recent updates to Ondsel make me feel like it's (maybe) time to dive in - tutorials like this go a long way! Thank you!

@norsenomad 17 күн бұрын

Great video! I found this very useful. Please make more videos using Ondsel ES - its UI and workflow is on another level, the best next step forward for struggling FreeCAD beginners. Thank you for all the useful tips and good explanations, so far, and all time and effort you must put into your quality videos. Cheers!

@Gumball_W 10 күн бұрын

You can have pretty much the same UI if you apply OpenLight theme and a few non-default settings (like a tree overlay and TabBar workbench selector) to FreeCAD 0.22 dev (to be released as 1.0). Most features, including VarSets, are also available upstream.

@hanswurst9866 16 күн бұрын

finally a new video!

@oddlytimbotwillison6296 16 күн бұрын

That is handy. I can see a case both for variable sets, and for spreadsheet/alias. I can imagine a scenario where it is just easier to see all parameters in a single sheet and be able to navigate them without a lot of GUI clicking, plus the ability to use cells for notes or related information.

@haysoos123 16 күн бұрын

So this is pretty much a replacement for Dynamic Data? Really great that there’s a built-in solution now.

@jjdawg9918 15 күн бұрын

OMG! that ticking sound in the background

@OficineRobotica 14 күн бұрын

Yes, you are right, it was a issue with the background music audio level being way to low thus in some cases only the snares are popping out . I'll correct that in the next videos

@leroycasterline1122 9 күн бұрын

At about 7:00, you set the cube's color to orange. I can't get this to work in FC 0.22.38001 or Ondsel 2024.2.38021 - the shape just remains gray. Could this be caused by a preference setting? Or perhaps it's a regression.

@marcus3d 16 күн бұрын

Why have a separate entity like CubeProperties with variables instead of just naming the relevant constraints and refer to them directly, or if it's some property then refer to that directly??

@OficineRobotica 14 күн бұрын

Var sets are not only about Property.Length or Integer. VarSet can store properties like Color, Link etc etc so they offer a centralized place where to modify values across file/files. Also, imagine handing out your complex file to a customer that want's to make on the fly modifications. Intuitive naming of variables in a VarSet can make this operation a breeze instead of explaining where to hunt for all the values. Also, VarSets can be used headless. That extends to the freecad file format and would be a whole tutorial in itself

@marcus3d 14 күн бұрын

@@OficineRobotica Good points.

@g3i0r 13 күн бұрын

You said that VariableSets can be used to store values across files. How does that work? Isn't a VariableSet stored inside of a FCStd file?

@indigo0086 15 күн бұрын

given the updates to freecad with .22 and 1.0 coming, and with some of the yet to be merged features of linkstage, which do you think you'll be working with more: Ondsel, 0.22dev/1.0, or linkstage?

@OficineRobotica 14 күн бұрын

I'm plan on using Ondsel/FreeCAD going forward, as functionalities are being actively ported over from Linkstage.