U-Joint Comparison - What to Know!
Рет қаралды 1,547
4 ай бұрынCheck out my new website for car parts and merch that I am selling - krusebuilt.com/
Parts reviewed (I recommend Spicer units):
1310 U-Joint; Amazon Link - amzn.to/47XiXcB
1330 U-Joint; Amazon Link - amzn.to/3w2gArR
1350 U-Joint; Amazon Link - amzn.to/42sn6UL
1310 x 1330 U-Joint; Amazon Link - amzn.to/47ZrrQz
The car is a 1966 Mustang Fastback with a 347 Stroker and T5 transmission.
Shot with GoPro Hero 12 with the Media Mod, edited on Davinci Resolve 18.
Gear I use:
GoPro Hero 12 Black - amzn.to/48oeFw3
GoPro Hero 9 Black - amzn.to/3ZCTpP7
Media Mod for GoPro Hero 9 thru 12 - amzn.to/3CPKOi2
Rode Wireless Go II mic kit - amzn.to/3iJrj4c
GoPro Hero 8 Black - amzn.to/3QLpj7V
Media Mod for GoPro Hero 8 - amzn.to/3ZCAeoA
GoPro Hero 5 Black - amzn.to/3XuKMUQ
GoPro Karma Gimbal for Hero 5 - amzn.to/3GIWa8P
Want to help support this channel, you can "buy me a coffee", check it out! www.buymeacoffee.com/krusebuilt
Credit for the music in the video:
::::::::::::::::::::
Epidemic Sound
Try it today! www.epidemicsound.com/referra...
::::::::::::::::::::
#krusebuilt
#kruseview
#Mustang
#1966
#fastback
@SmackeysGarage 4 ай бұрын
Good quick tip. I'll be using this!
@AndyKruseChannel 4 ай бұрын
Thanks!! :)
@5798Mike 4 ай бұрын
Nice information Thanks
@AndyKruseChannel 4 ай бұрын
Thank you! :)
@IvanCRF 4 ай бұрын
Thanks Andy. I'm changing my inline 6 3 speed manual 1969 mustang to a V8 with a C4. Interestingly, my original driveshaft fit the 8 inch diff I upgraded to. I also found my original driveshaft fit into the C4. The autoparts store suggested I remove the u-joints and bring them in to match them so I can be sure
@AndyKruseChannel 4 ай бұрын
That's probably not a bad idea. :)
@goldysgarage189 4 ай бұрын
Everyone in the hobby needs a digital micrometer to accurately measure what they have. This little tool is indispensable
@rustybritches6747 4 ай бұрын
I have a mustang with a 8" rear end and a drive shaft out of a 94 mustang nobody can seem to figure out what u-joint I need if anybody can help me I would appreciate it. I've tried asking parts stores and taking measurements, still can't seem to find it.
@AndyKruseChannel 4 ай бұрын
Just measure it and select the u-joint that fit the dimension of your driveline and third member. :)
@SlowInFastOut1776 4 ай бұрын
Andy over here spending money just to educate us! Great breakdown.
@AndyKruseChannel 4 ай бұрын
Sacrifices were made...... :)
@davevan8864 4 ай бұрын
Good basics
@AndyKruseChannel 4 ай бұрын
Sometimes it's the simple stuff that helps navigate through this hobby. :)
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 1,5 МЛН
Tinkerer's Adventure
Рет қаралды 3,2 МЛН
Nersva
Рет қаралды 5 МЛН
agro_fermer116
Рет қаралды 4,6 МЛН